How to clean the tiles with cement, how to clean the tiles with cement

If it is a relatively small amount of cement, toothpaste has a strong cleaning effect, and can play a good role in removing cement with small tile joints, and the operation is as follows.

Steps; 1. Squeeze the toothpaste on top of the cement tile and wait for 15 minutes.

2. Wet the towel with hot water and pour more water on the top of the tile.

3.Steel wire or sandpaper sandpaper to clean the gaps, be careful not to scratch the tiles, (easy to have marks) 4Mop it clean and pour the tile cleaner over the tiles that need to be cleaned.

5.Use a special tile cleaner and mop it all with a mop a few times to clean it all.

Just stick it with a steel wool ball dipped in water and brush it, the water can not be more just wet, and then wipe it clean with a wet towel.

If it is dry, scrape it with a spatula, and then use the above method.

Cleaning method of cement stained on tiles:

1. First wait until the cement is dry, and then soak it with grease. Then the cement loses its adhesion, and then use a shovel to clean the ball and rub it.

2. There is cement that has dried on the tiles, depending on whether the cement is thin or thick. Thin ones are lightly beaten with small wooden strips, and too thick ones are beaten with small hammers.

3. Use a professional tile decontamination cleaner.

How to clean the cement on the tiles:

Material preparation: dilute hydrochloric acid, toothpaste, rag, toothbrush, glass box.

1. Pour 10ml of dilute hydrochloric acid into the glass box (because cement is alkaline, hydrochloric acid is a strong acid, and the effect of removing alkaline cement is better).

2. Then squeeze an appropriate amount of toothpaste into the glass box (toothpaste has the effect of cleaning and decontamination).

3. Use a toothbrush to stir the dilute hydrochloric acid and toothpaste well.

4. Use a toothbrush dipped in homemade cleaning solution to carefully scrub the cement dirt on the tiles.

5. Use a rag to wipe the dirt on the tiles.

6. The cement on the tile has been removed.

1. You can use a small shovel to scrape putty first, and if there is still a part of the shovel that cannot be removed using hydrochloric acid or phosphoric acid solution, wipe it several times.

2. Because the glaze layer on the surface of some types of tiles (such as antique bricks and polished tiles) is not dense enough, or the surface is too rough (such as hemp bricks), after the cement caulking construction, some cement slurry will be filled in the small pores of the brick surface, causing the surface of the tile to be polluted and forming a cement mark.

In this case, it is necessary to judge whether the cement mark has penetrated into the inside of the tile, and if it has penetrated, it will not be able to be completely removed; If it is only cement mortar attached to the brick surface, then choose a professional tile cleaner (also known as cement mortar cleaner, concrete cleaner).

Cement is alkaline, to use acidic products to clean, but do not use oxalic acid to clean, that is a strong acid, will corrode the tile, once corroded, stains are easy to seep into the tile, it is more difficult to clean than the acacia. The cement on the tile can be cleaned with Yacaijie's descaler, keep the cement stain caulk stain without water when using, pour it directly on the cement stain caulk stain and wait for 1-2 minutes, and then wipe it clean with a pin digging steel wool ball or a hard brush, and rinse it with water immediately. Particularly stubborn stains should be increased or wiped several times to achieve better results.

Do not use a shovel, it is also easy to shovel the cement stains remaining on the surface of the tile, you can use the shield king descaling king tile cleaner to remove, it is specially to remove the residual cement on the surface of the tile, pour the solution, wait a few seconds, wipe it off, clean and clean, no negative effect on the surface of the tile.