The tiles of the new house are crooked, what should I do?

First of all, we must first rule out whether it is a problem with the tile itself, if it is not a problem with the product or a technical problem with the construction workers, we have the right to ask the workers to rework.

If the tiles are partially paved, you can use furniture to cover them; If all the paving is crooked, it is better to smash it and re-pave it.

The option to rework and retile will not be the case, and it will make your home more aesthetically pleasing.

1. Remove all the raised bricks, and then, clean up the bottom of the bricks, and then smooth them with cement, and then put the bricks on them.

Second, find a cutting machine, cut the warped floor strips, pay attention to cut the just warped, otherwise there is no cutting, lift up the warped floor, sweep it clean, and wipe each floor with floor glue and then glue it.

Third, the floor slag feast and burst, generally Bi Liang failed in the temperature of the rapid change drop cold or heat, the direct cause of the floor tiles and other building materials thermal expansion and contraction and squeezing and colliding with each other, mostly caused by improper decoration and construction and building materials quality.

It is recommended that when laying floor tiles, attention should be paid to the use of cement above 425 floor tiles, and the sand should be coarse sand filtered through dripping, according to a ratio of 1:2, and reserve 1 mm expansion joints.

Crooked wall tiles are a common problem that may affect the overall aesthetics and use of the wall. Here are some ways to deal with crooked wall tiles:

1.Reapply tiles.

If the tile is crooked, it may be because the tile is not flattened, and the tile can be re-tiled. First of all, all the tiles that have been glued are removed, the more accurate position is re-measured, and then reset and re-glued with cement. Although this method takes a long time, the effect will be better and will not affect the use.

2.Cut porcelain. If the wall tiles are not flattened, you can make a partial cut of the porcelain appropriately.

The specific operation method is that Qisheng first punches holes in the crooked tiles, cuts the porcelain with special tools, and then re-applies the tiles. This method requires professional tools and experience to operate, and it is not recommended to operate it yourself.

3.Adjust the base layer.

The tile can be crooked and poor because the base is uneven, you can adjust the base layer first to make it smooth, and then paste the tile. The specific operation method is to first scrape the base layer flat, fill in the dislocation part, then beat to smooth the surface, and finally re-apply the tiles. Although this method is time-consuming, it can avoid the recurrence of similar problems.

4.Use sewing cement.

The gaps between the tiles may cause the tiles to be crooked, and can be repaired with seam cement. The specific operation method is to fill the gap in the tile with cement, if the gap is small, you can use a special sewing agent, and then use a scraper to scrape the excess cement flat. This method is simple and easy, but the effect is limited.

In general, there are many ways to deal with crooked wall tiles, and different ways are suitable for different situations. Heavy tiles and porcelain cutting require certain professional skills to operate, it is recommended to find a professional to help quietly. Adjusting the base layer and using sewing cement can be operated by yourself, but the effect is limited, and you need to pay attention to the follow-up maintenance.

If the floor tiles are 8 cm crooked, they need to be re-laid to solve the problem. Here are the steps:

1.Clean the floor: First of all, you need to clean the original floor tiles, cement and other materials to ensure that the ground is clean and tidy.

2.Bottom layer: Lay the bottom layer on the cleaned ground, use Hu to make cement or floor tile binder, pay attention to soak in water before paving, reduce water absorption, and avoid excessive water absorption resulting in air infiltration, affecting the adhesion. Refers to the ruler.

3.Laying floor tiles: Lay floor tiles on the bottom layer, pay attention to the use of levelers, to ensure that each floor tile is the same flatness. At this time, it is necessary to check the flatness of the floor tiles, and only use partitions to separate the floor tiles.

4.Knock on the floor tiles: Knock the laid floor tiles firmly to ensure that the floor tiles are tightly bonded to the ground and there are no air gaps.

5.Caulking: After the tiles are laid, the gaps between the floor tiles need to be filled, and these gaps can be filled with special tile glue or cement joints.

6.Pre-use inspection: After the floor tiles are laid, it is necessary to repeatedly check the flatness of the floor tiles to prevent the recurrence of crooked paving, and at the same time, it is also necessary to wait for a period of time to ensure that the floor tiles are stable after the laying is completed.

The above are the specific steps to solve the crooked floor tiles, and it is recommended to find a professional decoration company or worker to operate.

Sigh, I didn't meet a good worker. Problems that shouldn't be there.

Now there is no way, the only way is to dismantle the floor tiles and re-pave.

Note: Remove the floor tiles carefully (must be dismantled by a bricklayer, otherwise it will be troublesome to touch the waterproof layer.) ）。After demolition, (if the bricks don't work, replace it, and there is no more money).

Note: This re-work, in addition to the drainage slope should be done well (if the bathroom area is small, the slope is slightly larger, the surrounding area should be as horizontal as possible, and the middle should be the lowest).

Remind you: when re-laying the bricks this time, be sure to put the back of the brick with a plain cement slurry mixed with Lloyal (waterproofing agent). In this way, when the bathroom is used, not only will there be no water accumulation on the surface, but also the mortar between the waterproof layer and the bricks will not accumulate water.

I don't know if you did this surface waterproof layer before, if you didn't do it, this time you did it, it didn't count as a waste of work.

Don't worry, don't get angry, it's not a big deal, it's just a little troublesome.

Happy and happy every day!

Another: At the door of the bathroom, the door stone must be installed, which is 5-8mm higher than the ground of the bathroom, which is the edge of the water retainer.