Is there a regulation for the size adjustment of the steel band of the watch?

There are no clear rules for the adjustment of the size of the steel band of the watch.

The size adjustment of the steel band of the watch needs to consider your own comfort and safety.

There are several aspects to consider: (1) the material of the strap, (2) the quality, size and thickness of the watch, (3) the shape characteristics of the wearer's wrist, and (4) the wearer's work type and habits.

Method steps.

1.Some people have very slender wrists, especially women, which requires truncation and removal of a lot of strap knots, and for discounted "metal straps" (butterfly clasps), it is necessary to consider the problem of left and right symmetry when truncating. The metal strap with a shell and some more "plate" straps (such as integral ceramics) will become more curvature after being truncated, which is easy to break the surface of the strap, and the length of the strap section is relatively large, which is more ugly to wear after being shortened, that is to say, such people should try to choose brand watches with leather and rubber straps.

2 .Some people have very strong wrists and may need to lengthen the strap to wear, but the general principle should be symmetrical so that the closed strap discount is in the center.

3 .The more troublesome is the person with a thick wrist but a relatively large taper, so it is not easy to find a suitable length, the watch is not easy to stay on the wrist, tight up and down and loose, such a person is more suitable for watches with thin and belts.

Precautions: Generally speaking, after wearing the watch, a fingernail (except for the thumb) can be stuffed between the wrist and the strap. When the diameter of the watch is relatively large and heavy, it is suitable to use a thickened leather strap or a solid metal strap, so that the watch can have a support control.

Nowadays, watches tend to grow larger and thicker. For larger and heavier watches, the position should be slightly higher than the wrist to prevent the handle from scratching the back of the hand, or to wear the watch towards the palm of the hand. Like people who usually exercise a lot, they should adjust the strap to be tighter properly.

There is no rule for this, and it can be used flexibly. Manufacturers will have their own strap size range, but it can also be adjusted according to your individual wrist size.

How to adjust the strap of a steel strap watch:

1. When you want to adjust the strap of a braided steel band watch, you must first prepare a flat-headed gadget, which is generally brought, and then use the tool to open the safety buckle on the strap.

2. After opening the safety buckle on the braided steel strap strap, use a small tool to pry open the small panel used to fix the position.

3. After prying, the small panel can be slid back and forth, and at this time, you can adjust the strap to the position that suits your wrist size.

4. After adjusting the size of the strap, it is necessary to buckle the panel to fix the position.

5. Then buckle the buckle of the braided steel strap on the other side to the small crossbar under the small panel, and then close it.

6. The last step is to cover the safety buckle on the braided steel strap and it is completed.

1. Adjust the position of the strap.

Before preparing to disassemble the strap, please carefully look at the arrow on the back of the strap, the downward arrow of the general watch chain is the bottom of the large and the top small, put the strap into the slot of the watch mixer, according to the aspect of the arrow, align the direction of the watch chain buckle nail Confucius.

2. Take out the meter adjuster and place the strap vertically in the gap and fix the corresponding position.

3. Take out the dialing needle for adjusting the meter, align the gauge with the pinhole, and take out the small hammer.

4. Then use a small hammer to gently hammer in the vertical direction.

5. Use pliers to pull out the pin in the strap and adjust it to the appropriate position as needed.

6. After removing the excess strap, finally knock it back with a small hammer.

Steel bands do not have holes to adjust like leather straps, and you need to use a meter adjuster to adjust the length of the strap as follows:

1. First of all, you must measure the strap, loop the strap around the wrist, see how many sections overlap together, and add a section on this basis to remove the number of strap sections.

2. Look at the arrow on the back of the strap clearly, the downward arrow of the general watch strap is the lower big and the upper small, put the strap into the slot of the meter adjuster, and align the direction of the buckle nail hole of the watch strap according to the direction of the arrow.

3. Loosen the handle of the gauge adjuster, put the strap into the gauge bar, and keep the steel of the gauge aiming at the pinhole of the gauge strap, and tighten it gently, and the steel needle connecting the strap will be ejected.

4. Remove the excess strap in turn, if the strap is longer, it is recommended to remove the same number of sections on both sides of the strap to ensure the balance of the watch when wearing.

5. Finally, connect the two ends of the disconnected strap, insert the buckle nail in the original head and tail direction, and put it into the meter adjuster to reverse rotate the ejector back to the needle buckle.

Note: The thimble of the meter adjuster must be aligned with the latch of the strap, otherwise the meter adjuster may be broken.

Do not twist the handle of the meter adjuster into the dead force, otherwise it may lead to the scrapping of the meter adjuster.

If you want to adjust the steel strap of your watch, you need to use a professional adjustment tool, you can buy a tool to change the watch bracelet online, of course, you can also send it to a special watch repair shop for adjustment.

1. First of all, unscrew the handle of the prepared meter adjuster, there is a thimble inside, and you need to take this thimble back.

2. After putting it away, first align it on the card pin of any section of the strap, and then screw out the thimble by adjusting the switch of the gauge, so that the watch steel belt is opened.

3. You should know that the steel band of the watch is connected by many small card needles, and you can disassemble the excess according to the actual length.

4. At the same time, we should also pay attention to the direction and position of the watch steel band into the meter adjuster, and also pay attention to the method, we can not push in from the side of the slot.

5. After adjusting the length of the watch band, we can press and hold the opposite direction of the arrow, install the needle and the strap, and restore it to its original state.

Hello dear! We're glad to answer your questions! How to adjust the length of the watch steel band is as follows:

Dear, the steel strap watch can be adjusted directly according to the thickness of the wrist after using the meter splitter to eject the small card pin. 1 Open the meter splitter, unscrew the handle of the meter splitter, and return the thimble to the side parallel! 2 Eject the small card pin Aim at the small card pin between the strap to be removed, screw the handle of the meter dismantling and eject the small card pin.

3. Put the strap into the belt slot, put the strap into the "belt slot" of the meter splitter (the needle steel bolt has two ends, one end is flat, one end has a slotted slit, and one end has a card position, so the sharp needle should be pushed from the flat end to the top not from the top of the slotted end). Hope it helps! Look! Kiss.

The method of adjusting the strap of a steel band watch is:

1. When disassembling the bracelet, the first thing to do is to remove the stud from the bracelet through the gauge. You can slowly rotate the watch handle to push out the "buckle peg". Finally, when installing, you can reverse the top back to "buckle the nail".

When you open the strap, you can use a special watch regulator that matches its shape. Place the strap in the "watch removal slot" and remove the bracelet by ejecting it firmly according to the stud interface on the gauge controller.

2. The bracelet and the back cover are connected by a tight fit, which is commonly used in old-fashioned watches and women's watches. The repairer can use appropriate tools to rotate the handle of the gauge to the outermost edge, align it with the "strap attachment button" and slowly rotate the handle to eject the "buckle button". Finally, when installing, you can reverse the top back to "buckle the nail".

If not, you can pry up the back cover in a position where there is a large gap between the stud and the bracelet, preferably in a symmetrical position, to avoid damaging the back cover.

3. Special reminder to remove the disassembled watch section, re-nail it with a bracelet nail, and use a small hammer on the side of the rubber head to avoid hammering it on the watch by mistake.