How to deal with the ground subsidence of the plant? How to deal with the subsidence of the factory

How to deal with the ground subsidence of the plant? First of all, we need to figure out one of the most important issues, that is, only the ground subsidence, or the plant structure has also subsided, if the former can still be handled, the ground can be reinforced, and the reinforcement measures of piling can be adopted; If it is the latter, the plant structure has also settled, especially the uneven settlement, it is recommended to rebuild as the best policy, even if the treatment cost is very high, it is better to choose a new safe plan.

This general restoration is only temporary, and it is necessary to rebuild it for safety reasons.

If the ground of the factory sinks, I think the previous foundation is not very good, and if you want to be able to deal with this matter better, you can also re-stabilize the ground after planing, and then re-cement the floor.

Just read your question. If the plant is not demolished, someone is willing to repair it. I'm afraid it's unreliable.

The ground of the factory is sinking, and my suggestion is to drive piles and support the plant with channel steel. (when beams). Find several important support points in the workshop and workshop, and the triangular brace.

Material costs, labor costs, (welders). It doesn't cost much.

According to the plant foundation sinking solution, finding a reinforcement company with structural reinforcement qualification can solve the above problems, mainly through the existing foundation reinforcement treatment measures to prevent the plant foundation from continuing to sink and restore the normal function of the building. In addition, if the plant is tilted, it is also necessary to carry out tilt correction and reinforcement treatment.

How to deal with the sinking of the factory floor under the ground of the plant? At this time, you can ask the ground to inject water, inject some water, probably the wind is empty, destined for water.

If this is the case, it is likely that the foundation of the plant is not strong enough, so such a factory cannot be in production, so it must be transformed.

Vertical shafts are drilled around the perimeter to reach below the foundation, drilled holes, and cement and fly ash are mixed with slurry.

Subject, because your factory is full of large-scale equipment, if you don't want to dismantle the plant, you can only choose foundation reinforcement. The damage to our factory was much worse than yours, not to mention the shutdown at that time, and there was no place to place the large equipment in the factory. The whole construction period should not exceed 20 days.

It is said that the warranty is as long as 20 years, but it is best to solve the problem now. Would you like to take a look? Don't forget.

(1) Chisel out all the floors with large cracks and settlements, use pile foundations to reinforce the foundation, and pour concrete floors in accordance with national standards.

2) Demolition of all walls and towering buildings built on the cracked and seriously settled floor, after the floor is re-poured in the masonry wall, the cracked wall that is not directly connected to the floor is reinforced with double-sided reinforced mesh cement mortar.

3) After the foundation treatment and settlement is stable, the waterproofing of the seepage roof is redone, and the permeable rust inhibitor is applied on the surface of the low structure of the seepage part, and the cracks should be repaired by grouting method when the cracking of the floor panel is serious. When the structure is reinforced, the original structural components should not be harmed as much as possible, and the preferential selection and stability problem of the floor foundation treatment scheme; deformation problems; Infiltration issues. The purpose of foundation treatment is to improve the bearing capacity of weak foundation, reduce the compressibility of weak soil, and reduce foundation settlement and uneven settlement.

The principles to be followed in the treatment of the foundation are: advanced technology, economic and reasonable, safe and applicable, to ensure the quality of the structure of the floor, the floor plate directly bears the ground load, the plate is connected to the main structure, and the floor plate also adopts the same foundation type as the main structure, and the overall deformation of the two is consistent.

Ground subsidence is caused by geological changes or human activities, which can lead to problems such as tilting of buildings, damage to underground facilities, and surface subsidence. For ground subsidence, we should take appropriate measures to deal with it.

First, monitoring and early warning need to be strengthened. The use of advanced technology to establish a monitoring system for land subsidence, real-time monitoring of surface subsidence and early warning, and timely measures to protect important facilities such as underground pipelines.

Secondly, grouting and other technologies can be used for reinforcement treatment. Grouting is to fill the soil gaps by pouring cement slurry and other materials to make the soil solid and avoid underground cavities and collapses.

Finally, and most importantly, the need to strengthen comprehensive governance and planning. Formulate reasonable urban planning, scientifically and rationally use land resources, strengthen infrastructure construction, realize reasonable diversion, avoid rough sources and avoid excessive exploitation of groundwater resources, and reduce the damage and consumption of soil and forest resources.

In modern urban construction, land subsidence has become a problem that cannot be ignored. Only by dealing with it through scientific means can we ensure the stability and development of the city.

The treatment method of building foundation subsidence is as follows:

1. There are slight cracks in the wall due to subsidence and there is no spreading, and the cracks can be filled directly.

2. The subsidence of the building affects the safety of the house, and the foundation needs to be reinforced.

3. When the building sinks obviously and the foundation is weak, the pile foundation can be used to bear the load of the additional layer, and then the foundation cap is increased, so that the two are connected, and the foundation settlement is checked.

Before building a house, it is necessary to survey the land where the house is built, and if there is no survey, the construction will be carried out, and then the foundation will easily sink, which will bring serious consequences. When laying the foundation, there is no calculation according to the actual brother or buried design of the house, which leads to the unreasonable form of the designed foundation, and there will also be sinking.

Reasons for sinking

When the foundation is constructed, it is not carried out according to the drawings, or it does not meet the specification standards, and cutting corners is also a very important reason. If the area around your house is still under construction, then in the process of construction, it is likely to affect the foundation of your house and cause sinking. If you add it at will or pile it up in a large area around it in the process of living, it will also cause the foundation to sink.

In slight cases, cracks will appear in the walls of the house, affecting the overall aesthetics. Severe uneven settlement will cause the house to sink and tilt, and large areas of cracks will appear on the wall, which will seriously affect the stability and safety of the house. Floor subsidence is the most common subsidence phenomenon, as long as the cracks are controlled and there is no spread, the basic joints can be repaired.

The foundation sinking should be paid attention to, and it has potential safety hazards.

Whether it is a community or a rural self-built house, the problem of foundation subsidence may occur, the foundation subsidence will lead to the tilt of the building, the crack of the floor and the wall, and this problem has brought problems to the safety hazards of the building, if we live in the building foundation sinking how to deal with it? 1. What to do if the foundation of the building sinks 1If the house is built on the land with relatively soft soil and low load capacity, the bearing capacity of the pile can be increased in the second construction after the pile originally meets the specifications of the candid conformity, but this needs to be determined according to the actual situation of the pile settlement.

2.When the land for housing construction is good and the load-bearing capacity is high, if the foundation sinks, the subsidence problem can be solved by increasing the area of the foundation. 3.

If the house foundation is made of reinforced concrete, it can be reinforced by anchor static pile, if this foundation does not meet the situation of pile pressing, the foundation can be thickened and widened before pile pressing, and then the pile is pressed. 4.If the data of the geological survey of the house is not imperfect, it is because the site is too complex at that time, and the subsidence of this situation makes the Nai people need to re-survey the geology and find out the cause before it can be reinforced.

5.If the original foundation stiffness and integrity are relatively good, and with reinforced concrete ground beam, you can use the lifting beam or pick beam to load, and there is no need to reinforce the mu cavity foundation. 6.

You can also use the foundation to re-grouting reinforcement, when using this method, it needs to be noted that when the collapsible loess, filling soil and other grouting reinforcement cause the foundation to deform, it is necessary to add a quick-setting agent or an expansion agent. This is to avoid an impact on the house. Summary:

The above is the article shared for you today What to do with the foundation sinking, once the foundation subsidence occurs, you must immediately find a professional to deal with it, do not deal with it yourself, because some improper operations are likely to expand the potential safety hazards. For more related content, please continue to pay attention to Qeeka Home.

Summary. Kiss! Hello, happy to answer your <>

Pro, building foundation subsidence treatment method: one is the cement grouting reinforcement method, which needs to mix the water glass slurry and cement in a certain proportion and inject it into the soil, but this method can only inject the grout into a slightly larger gap. Another method of reinforcement is lime pile squeezing, which injects cement into very small gaps.

Finally, the surface can be filled with soil.

How to deal with the subsidence of the foundation of the building.

Kiss! Hello, I'm glad to answer for you. Pro, the building building void hail hall foundation sinking treatment method:

One is the cement grouting reinforcement method, which requires the water glass slurry and cement to be mixed in a certain proportion and then injected into the soil, but this method can only inject the grout into a slightly larger gap. Another method of poor reinforcement is lime pile squeezing reinforcement, which can inject cement into small gaps. Finally, the surface can be filled with soil.

It is normal for the foundation of the house to sink slightly, because the soil texture of the foundation is related to the dynamics, which is embodied in the cracking of the wall and the cracking of the floor slab. The main main structure is fine, because the frame structure is slightly sunken as a whole. The specific measures are as follows:

1. Observe the settlement of the foundation, determine the treatment plan according to the settlement situation 2, take measures for the foundation hail of the sinking bee position, such as pressure grouting, etc., control the further settlement of the foundation 3, set up the external foundation and the contact beam or add the ground beam in the structure to comb the existing foundation with the sail overhead, and change the force transmission path of the superstructure at the same time 4, observe whether the settlement of the foundation is delayed or end the bend, formulate the repair plan of the superstructure 5, repair the superstructure, and add a ring beam structural column to strengthen the integrity of the superstructure.

If the quality is unqualified due to the wrong construction plan, the foundation sinking is the responsibility of the construction party; If the design unit, the supervision unit, etc. also know that there is a fault, they shall be liable according to the fault of each other.

If the quality is unqualified due to the wrong construction plan, the foundation sinking is the responsibility of the construction party; If the design unit, supervision unit, etc. are also at fault, they shall be liable according to their respective faults. When the owner finds the problem of foundation subsidence, he must first ask the developer to reflect, and then the problem of the construction party, design unit and supervision unit.

After the foundation sinks, it needs to be reinforced. Before reinforcement, it is necessary to inspect the cracks to understand the development of the cracks, and then select the corresponding reinforcement method according to the degree of cracks. If the settlement occurs because of the uneven construction of the foundation, it usually has a great impact on the bearing capacity of the building, so it is necessary to repair the foundation by caulking or grouting, and after reinforcement and repair, the foundation can be used normally.

However, if the area of foundation subsidence is too large, and the sinking place is unevenly distributed, the building on the foundation is easy to tilt and crack, and this situation can no longer be used normally, and it needs to be moved to a safe place as soon as possible.