Can you use a black one when filling a color cartridge?

It's completely OK My home is an HP printer I used up a black original ink cartridge to know that I can add ink to this thing, but the original can't be refilled after the original is used up, so I started the idea of color ink cartridges When the color ink cartridge is only one-third left, I will add black ink to each hole Now the print is very good In my experience, I tell you that it can be added The ink I bought is also bought on the Internet A very large bottle is very cheap It's okay to mix with the original HP ink cartridge There is no other person to say that the card or anything like that It's just that the typing is magical, and it's going to be black with a little red or a little bit of blue, sometimes it's purple, and it doesn't have any effect other than that.

If you have an original cartridge, no. Because there is the original ink left in the old ink, if the two inks are mixed together, it will change color, at least the printed image will be flowery, in addition, the concentration of the two inks is not the same, which may cause a blockage.

If you are using a sponge-free ink cartridge, it is possible to install black ink as long as the ink cartridge is cleaned! But in this case, there is only a document, or black and white, there is no point! Unless the stamen on your cartridge is broken, you can try this method to type documents!

To put it simply: it will be clogged! Unless you're not ready to ask for it.

It depends on what kind of run-in you use.

The method of adding ink to color printer cartridges is as follows:

1. Remove the label on the upper part of the cartridge and see that there are five small holes under the label.

2. Distinguish the color, one hole is red, two holes are blue, and two holes are yellow (you can use a toothpick to insert a small hole to distinguish the color).

3. Spread a good facial tissue under the nozzle without falling off the confetti, so as to prevent the ink from bleeding from the nozzle. If it is a slight bleed, a few more color blocks can be solved (this method can be followed for the bleeding of the nozzle part).

4. Insert the needle into the small hole for ink injection, and inject an appropriate amount of ink.

5. Wipe the area around the hole and label it.

How to add ink to ordinary printers:

1. Remove the sealing patch on the ink injection hole first, and then press the steel ball in the ink injection hole into the box with the thin end of the bead pushing tool.

2. Remove the rubber cap on the ink cylinder, insert the short needle into the mouth of the ink cylinder and press it tightly.

3. Buckle the nut into the top of the ink cylinder first, then insert the ink cylinder into the ink injection hole, and screw the screw into the nut hole.

4. Rotate the screw and slowly push the piston until all the ink is injected into the cartridge. (Note: Two inks must be added at a time.) ）

5. Remove the ink cylinder, put a new steel ball in the ink injection hole, and gently press the steel ball with the thick end of the ball pushing tool until it is level with the orifice. Then apply a circular patch.

6. Attach the ink nozzle of the ink cartridge to the rubber key, and press the tail of the ink cartridge hard to make it snap into the protective clip.

7. Remove the short needle of the empty ink cartridge, insert the mouth of the ink cartridge into the rubber keyhole, and press it tightly. The anti-rotation screw springs the piston, sucks in the 2-3 mm high ink, and gently removes the ink cartridge.

8. Finally, take the ink cartridge out of the protective clip, wipe off the ink stain with a clean paper towel and install it for later use. At this point, the entire process of ink filling is over, and your printer can start working again.

Summary. Although in terms of color principle, it is also possible to get black by mixing other colors. However, the printer is printed with black ink by default.

Most printers will give an error as soon as one color cartridge is empty. Prompt: Ink is out and cannot be printed. Other words.

You can't even print a red piece of paper now.

No. Although in terms of color origin, it is also possible to get black by mixing other colors. However, the printer is printed with black ink by default.

Most printers will give an error as soon as one color cartridge is empty. Prompt: Ink is out and cannot be printed. It is also said that it is simple and void Zen.

You can't even print a red piece of paper now.

Why do black cartridges break.

Generally speaking, the printer cartridge is broken, which can be divided into two situations: one refers to the life of the ink cartridge that your printer tells your friend, and the machine cannot recognize the ink cartridge, in this case, there is no other solution except to replace the ink cartridge in the slip hall. Socks let Huai.

There is also a situation that the life of the ink cartridge has not reached but there is no ink, and in the case of no ink on the cartridge, individual models can be inked. But from the perspective of the industry, it is best not to add ink, because if you do not seal it well in the process of adding ink, it will burn out the nozzle of the opening printing machine.

Will the paper on the metal dots on the black cartridge fall off the black cartridge and the black cartridge will break.

To add ink to the color cartridge, first find or remove the color cartridge and remove its label. Once the cartridge is peeled off, you can start drilling holes for the cartridge. Once the hole is drilled, it is time to refill the ink using a professionally induced syringe.

Modern ink cartridges mainly refer to the parts used in inkjet printers to store printing ink and finally complete printing, and in the old days, it refers to the stationery utensils used by people to hold ink.

In general, ink cartridges can be divided into split cartridges and integrated cartridges. The one-piece cartridge is the integration of the printhead on the cartridge, and the split cartridge refers to the product that separates the printhead and the cartridge design.

Ink cartridges have a very important position for the entire inkjet printer, especially some low-end limb loss printers, which have reached the price of 2 cartridges equal to 1 printer.