How to put the rope of the absorbent potted plant, and how to pull the absorbent rope of the flower

Method 1. <>

1. Buy absorbent ropes such as cotton ropes and candle wicks.

2. Soak a section of the cotton rope in a glass of water, tie a knot at the end of the cotton rope, and soak in water.

3. When the potting soil is half dry and half wet, you can take the plants out of the pot, and you can use a gardening shovel.

Method two. <>

1. Put the soaked cotton rope into the drainage hole of the flower pot.

2. Leave the section of the knot in the potting soil, and the cotton rope will be fixed at the bottom of the pot.

3. Put new soil at the bottom of the pot, and automatically absorb water after compaction.

1. Prepare beer bottles (other wine bottles are also acceptable), scissors, hemp rope (thicker rope), alcohol, lighters, gauze, and soil that you have drunk at home.

2. Use hemp rope to wrap a circle around the upper part of the bottle, tie a knot, and then apply alcohol.

3. Use a lighter to light the rope.

4. After the rope is burned, quickly put it into cold water to cool. This makes it easy to divide the glass bottle into two sections.

5. To avoid scratching injuries, use sandpaper to polish the edge of the bottle.

6. Cut the gauze into squares, and then buckle two small holes in the middle.

7. Take a long piece of hemp rope, pass the two ends of the hemp rope through the two small holes, align them into a strand, and tie a knot at the end.

8. Put the head of the beer bottle upside down in the tail, put the gauze and rope in the upper part, trim the exposed gauze, and then fill the soil.

9. Plant the prepared green plant seedlings into the soil, add water to the bottom of the bottle, and soak the tail of the hemp rope in water.

10. In this way, even if the flower friends usually forget to water, it is fine, it will automatically absorb water.

The use of the lazy basin suction rope is as follows:

First, the first is to put the absorbent cotton rope through the bottom hole of the flower pot.

2. After the absorbent cotton rope passes through the hole, fill half of the soil in the pot.

3. Pour water into the water storage basin. Note: The water level should not be next to or exceed the height of the pot.

Fourth, finally transplant the plants that need to be planted on the pot. Note: Use this lazy pot only to grow water-loving plants, such as: pothos, copper coin grass, etc.

A method of making an automatic absorbent potted plant with absorbent cotton rope.

The first step is to wash the flower pot and wash it with clean water.

The second step is to ream.

thread, the threading hole and permeable hole at the base of the upper basin are properly expanded with a knife to make the thread permeable, and then 3 absorbent cotton threads are threaded from the 3 large holes to the appropriate position of the upper basin (about 2 cm lower than the edge of the upper basin).

The third step is to put the filtered water sand and gravel.

Put the slightly larger sand and gravel on the bottom layer so as not to block the water hole, and gradually put the fine sand and gravel up with a thickness of about 2 to 3 cm.

The fourth step is to put nutrient soil.

Put the prepared nutrient soil into the pot, the thickness is determined according to the root length of the flowers and trees, straighten the cotton thread while putting it and slightly compact the soil, the cotton thread can be pulled up and down to ensure the distance and vertical from the pot mouth.

The fifth step, plant flowers and trees, put the flowers and trees in the appropriate position of ** or 3 cotton threads, and slowly place the soil and slightly compact it under the condition of ensuring that the roots of the flowers and trees are sparse and the cotton threads are vertical, usually the soil should not be full, and the space for placing moisturizing moss or decorative materials on the surface should be left to avoid flowing out of the pot when watering.

Step 6: Put moisturizing moss or other decorative materials to moisturize and look good.

The seventh step, watering the root water, slowly and evenly watering with a shower, one-time watering can be done, after watering, the upper pot is placed on the lower basin, and the lower basin is not filled with water at this time, so as to ensure that the excess fixed root water in the upper basin is discharged into the lower basin, usually 3

After 5 hours, lift the upper pot after draining, clean the water line, pour out the dirty water in the lower pot and wash it, then fill it with clean water and put it in the position where you want to put the pot, and finally put the upper pot on the lower pot and wipe it clean.

How to put the potted water absorption rope? Like this, you just tether it to the bottom of this basin and put it in a tray underneath. It can be sucked up automatically.

The pot rope is a common watering tool for potted plants, which can help plants suck water out of the pot, so that the plants can get enough water.

However, if not used correctly, it can also bridge chains to adversely affect plants.

Therefore, when using the absorbent rope for flower pots, we should pay attention to the following:

First of all, make sure that the length of the absorbent rope of the pot is suitable for the needs of the plant, not too long or too short, otherwise it will affect the normal growth of the plant.

Secondly, the finches should ensure that the material of the absorbent rope of the flower pot is safe, and do not use materials containing toxic substances to avoid contamination of the plant.

Thirdly, make sure that the flower pot absorbent rope is installed correctly, and do not install it on the root of the plant, so as not to damage the plant.

Finally, make sure that the rope of the pot absorbs water is clean and washed regularly so that the plant is not attacked by germs.

In short, the flower pot absorbent rope is an effective tool for watering plants, but you should also pay attention to the above points when using it, so as not to adversely affect the plant.

Only when used correctly can plants get enough water and grow healthily.

1.The first step is to thread the absorbent cotton rope through the hole in the bottom of the pot.

2.After the absorbent cotton rope is passed through the hole, half of the soil is filled in the pot.

3.Pour water into the basin. Note: The water level should not be next to or exceed the height of the pot.

4.Finally, transplant the plants that need to hail and shout on the pots. Note: Use this lazy pot can only grow water-loving late wild plants, such as: pothos, copper coin grass, etc.

3 liters - 4 liters. The self-absorbing flower pot is a kind of self-absorbing water container, which is divided into an outer pot and an inner pot, the outer pot is a container without drainage holes, and the inner pot is a planting basket, too large a pot will lead to poor water quality, so 10 mm water absorption rope with 3 liter-4 liters of pots is completely fine.

How to use self-absorbing flower pots: cleaning and disinfection:

1. Disinfect with carbendazim and potassium permanganate first.

2. Cotton rope perforation: separate the inner and outer basins, thread them according to the number of holes, and thread the cotton rope into the inner basin holes.

3. Fill the pot with soil: Put the soil into the pot, and tap the pot after the cotton thread is straightened out to fix the cotton rope.

4. Plant potting: plant the plant into the pot, carry out the second line management, connect the outer pot with water to make the cotton thread contact the water surface, and then put the inner pot into the outer spray. Pay attention to blind grinding: check the water level frequently and add water in time.