What to do with manual haircut clippers clipping hair?

There are several reasons why clippers clipper hair is pinched. First, due to long-term use, there is rust between the two plates of the fader, and the hair will be clamped, a little engine oil, manual movement a few times, and the rust liquid will be discharged, and it will be fine. Again, there is hair sandwiched between the upper and lower boards, and once there is a hair sandwiched in the middle, there will be a gap between the two boards, and the hair will definitely be clipped.

This requires unscrewing the screws on it, removing the two plates, wiping them with a clean cloth, removing impurities, and then installing them, and you're good to go. The third case is the installation problem. Used hand clippers, the two plates will leave traces of friction, when reinstalling, must be installed in accordance with this trace, only this way, in order to ensure that the two plates fit completely, that is, people often say "dressing", in addition, there is a key point, that is, the teeth of the two plates must coincide together, many people ignore this detail, when pushing the movement, there is no effect, once stopped, it will pull the hair, this is the reason.

The above is the repair of the general situation, if you have tried, or clip the hair, it means that the use or storage is improper, the fader board is separated, there are traces that are not easy to see the naked eye, for the layman, there is no way, you can only find a professional grinding master to repair. If there is no professional repair nearby, you can use sandpaper of more than 6,000 meshes, put it on the glass plate, press the two plates flat, rub it a few times, install it, and point some oil, there should be no problem.

You can put some oil on the fader, so it will be a lot smoother, of course, you can also change to an electric one, now an electric fader is not expensive, you can buy a good quality for a few dozen dollars.

After the haircut, remove the cutter head, use the small brush that comes with it to sweep away the dandruff in the direction of the blade, and then clean the head with water, and be sure to dry it after cleaning to prevent rust. Once the head is completely dry, apply a few drops of lubricating oil to the blade.

For hair clipping, it is recommended to replace a wider plastic clipper, and it is also recommended to change a haircut clipper.

It may be that the time is too long, and then there is no oil in it and it is more astringent, you can drip some oil from the top of the clipper, and then clean up the hair in time, and the clipper can be used a little better.

It should be the clipper for this haircut, and it should be missing this oil. That is to say, you should give him some oil, which means that the clippers of this haircut have the oil of this clipper, so you can give him some oil.

If this happens, it means that the blade inside is not sharp enough, and you need to change it, and there will be no such phenomenon. If the blade is used for too long, it will become less sharp, and then it will clip the hair when used. Generally, it is necessary to replace the blade after about three months of use, and it will not occur if you replace a blade yourself.

Clip your hair with a manual hairclipper, and you can just put a little oil on top of the clipper. If the clipper has oil on it, it will be smooth enough, so it will not be easy to clip the hair when cutting hair.

If you have your hair cut with a manual hair clipper, you can use scissors to cut your hair.

It's better not to use this manual haircut clipper to push the hair, you can use an electric clipper, which will be better. Or go directly to the hair salon, which will also be more convenient.

If the cutter head is used for too long and the shear force decreases, you can buy a new cutter head to replace it, and buy a cutter head of the same model to match.

1.Adjust the compression nut of the upper blade so that the upper and lower blades fit effectively, 2The blade has a dull edge and needs to be sharpened to regain sharpness.

Here's how to grab clips to clip your hair:1. Use two to three small grippers.

Use two or three small grippers to styling, curl a little curl, and style the two clips with a little space between them, and loosen the strands a little.

2. Clamp the bangs with a gripper.

Twist the strands of bangs half a circle into a circle and clamp them.

3. Decorate the sides of your hair.

Tie up your hair and decorate it with small grab clips at the side.

4. Use a variety of small grippers.

Use butterfly grippers, small colorful flower-shaped grippers.

Clip Clip Hair Tutorial:

1. Large grip clip.

Steps: 1. After the hair is combed and smooth, tie the hair into a low ponytail with a rubber band, and then pull the rubber band close to the end of the hair.

2. Twist the ponytail and rotate it upward, twist it to 2 3 places in the hair and start to retract it, put the tail of the hair in, and finally clamp it with a gripper.

2. Medium gripper.

Steps: 1. Divide the hair into two parts, twist it into a twist shape, all the way to the end of the hair, so that the hair is more layered and fluffy.

2. Fold the ponytail to the end of the hair after twisting, and finally fix it with a grab clip. This way of pinching hair is firmer, and at the same time, the temperament is more gentle.

3. Small grip clip.

Steps: 1. Divide the hair into three equal parts, weave it into a twisted braid, and weave it into a small section.

2. Prepare a small grab clip and clip it on that short section of braid, so that the low ponytail clipped, which is not only gentle but also very Korean.

Material Required: Cross-cone.

1. First of all, clean the brush so that the brush is clean, and the brush is in a horizontal state, with the two screw holes facing up, and install the small cutter head.

2., put the tip of the knife on the brush, and then get stuck. Note that the two holes on the small bit are aligned with the two screw holes on the brush so that the screws can be installed next.

3. Then cover the head of the knife with a large knife head. Similarly, the hole in the large bit should be aligned with the hole in the small bit for the next screw installation.

4. Use a Phillips screwdriver to install the Phillips screwdriver on the large cutter head, so that the large cutter head and the small cutter head are all fixed. will be installed on the head.

5. All parts are installed.

It's better to read the manual, or send a **. Inside is the motor and a moving head, and then the scissor head. Tear down the counteraction.