In the process of renovation, where are the decorators most likely to cut corners?

<> in the process of decoration, the most feared is that the construction unit is shoddy, cutting corners, if the owner does not know how to decorate.

Or if you don't pay attention, this can happen.

1. Small surface treatment.

The so-called "small noodles" are some small places that the owners cannot see with their eyes and do not pay much attention to, such as the upper edge of the door, the bottom of the window sill board, the inside of the heating hood and other places, where some workers will cut corners or even do nothing to deal with.

<>2 sewer pipes.

There are many homeowners who use their newly renovated houses within a few days to find that the sewer pipe is blocked, and then spend a lot of effort to unclog him.

This is caused by the fact that the decoration master is too lazy to pour the construction slag and uses the sewer as a garbage dump, so when accepting the house, be sure to test whether the sewer is unblocked with a large amount of clean water.

<>3 Wall substrate treatment.

For the interior wall decoration of the living room, the general latex paint needs to be painted more than twice to be qualified. If the workers are not serious or perfunctory in the construction, color difference often occurs, especially for darker latex paints.

Latex paint needs to be added with a certain amount of water before use, and the prepared latex paint should be used up at one time. It is also best to apply the same color paint in one go. If the wall needs to be repaired after the construction is completed, the entire wall should be repainted.

<>4 wire splices.

Electricians do not wire according to construction requirements when installing sockets, switches and lamps. Especially when the owner uses some electrical appliances with large power consumption, it is easy to cause the switch and socket to heat up or even burn, which brings great losses to consumers.

In the construction, supervise the electrician to carry out the construction in strict accordance with the operating procedures, and after all the switches and sockets are installed, they must be used to see if there is heat in these parts.

<>5 wall and floor tiles are paved.

When tiling, if the master is lazy and perfunctory, then your wall and floor tiles will definitely have a lot of hollow drums, and even uneven gaps, so try to look carefully when accepting, and knock each piece down.

6. Wall grooving.

Buried pipelines must be slotted in walls and ground in order to bury the pipelines. A small number of workers carried out the grooving operation in a brutal manner, which not only damaged the load-bearing structure of the building, but also caused damage to other pipelines in the vicinity.

Before construction, it is necessary to reconfirm the direction and location of the pipeline with the construction team leader. For different wall structures, the requirements for slotting are also different: the load-bearing wall in the house is not allowed to be slotted, and the wall with insulation layer is easy to cause cracking on the surface after slotting, and in the ground slotting, it is necessary to be careful not to damage the floor slab and cause trouble to the residents downstairs.

<>7 seam treatment.

From the delicacy of the joint treatment, you can see the sense of responsibility of the construction team. For example, at the junction between the door and the wall, when painting, it is generally necessary to paste tape on the edge of the contact between the door and the wall to ensure that the junction is still smooth and beautiful after painting. However, if the unscrupulous merchant omits the step of applying tape, there may be rough decoration with crooked corners, which will affect the appearance.

It's most likely to cut corners and paint latex when customizing cabinets, so we have to pay special attention to these two links.

All parts of the decoration process can cut corners, the ceiling single-layer double-layer gypsum board, putty, as well as the sliding door set door, the same type of board for custom furniture, ** is also very different.

It is most likely to cut corners in the sewer pipe, because the decorator may use the place where the sewer pipe is located as a waste discharge place, where construction waste is piled up, which will easily cause the sewer to be blocked.

Some waste residue and garbage in the construction process can easily be poured into the sewer by workers to save trouble, which is the work done by the most unconscionable people. Because of the sewers, once it clogs our later life, it will be very troublesome.

<> "Renovation works easily.

Something that cut corners.

1. Waterproof construction, generally the place to do waterproof is mainly the bathroom, if there is a sink washing machine on the balcony, you can also do waterproofing, the kitchen has a floor drain to do waterproofing, you don't have to do it. Bathroom waterproofing general delivery developer will do a layer, the basic quality of this layer is very poor, in the decoration to do the second waterproofing, some decoration workers in order to save trouble and save costs, will fool the owner that it has been done, and there will be a situation of tile hollowing off and leakage in the later stage. The correct way is to clean up the original waterproof layer and redo the waterproofing to avoid future troubles.

2. Hydropower construction, some decoration companies will use small-sized wires in order to reduce costs, and when you can wait for you to move in, there will be tripping at both ends in three days, so the owner will personally check the wires when choosing them.

3. In addition to paying attention to the wire itself, you should also pay attention to the most used conduit, the general decoration company will tell you that the PVC material can play the role of flame retardant insulation, but it should be noted that different brands, different quality and strength, the effect is also different. When we choose, we have to tell the decoration company, with the same brand and water pipe quality will not be too bad, if you are worried, you can test it on the spot, intercept a piece of line pipe, ignite it with fire, if it can continue to burn, this is resolutely not used, there will be potential safety hazards.

4. Bricklayer wall, is also easy to cut corners of the place, generally the wall should be added to the steel bar, and the steel bar is connected, so as to ensure that the later stage does not crack, some workers will not put the steel bar or simply put a few to deal with the matter, the later check-in wall problems, and then repair it is troublesome.

5. Woodworking ceiling, now the ceiling has a wooden keel and a steel keel, the advantage of the wooden keel is that the construction is simple, and you can do a variety of complex ceiling shapes, but the strength of the wood and the waterproof, waterproof and moisture-proof are not as good as the steel keel.

The steel keel construction is simple, strong and durable, but can not do too much modeling, and pay attention to the main keel spacing can not exceed 80 cm, the secondary keel spacing is 30 to 50 cm, some decoration workers in order to save materials, will make the spacing larger, it will affect the load-bearing of the ceiling, and the ceiling will be deformed and cracked in the later stage.

6. Wall construction, wall decoration Some companies will paint the wall with wall solid before painting, so that the whole house is yellow wall and green space, and they are very professional when they look beautiful. In fact, this kind of wall solid does not conclude that there is any benefit to the wall, but in the decoration construction, workers will add a large number of inferior glue to cut corners, there will be a large amount of formaldehyde and heavy metals in the glue, and then brush the latex paint to cover it, formaldehyde volatilization will be particularly slow, which will cause you to live in a toxic environment for a long time in the later stage.

These places that are easy to cut corners in decoration require us to pay attention to them when decorating to avoid unnecessary troubles in the later check-in.

**It is necessary to see clearly the specific project details, unit price, quantity, and construction technology to see whether the project is complete, the unit price is complete, the quantity is correct, and whether there are variables in the construction. (If you don't understand the decoration at all, you can find a relative understanding of the construction at the same time, for example, whether the water and electricity are all covered in the **, to see and ask clearly that there will be those, what has come out is how much money is a square, to ask clearly, otherwise when the time comes to the decoration, I don't know that so much money is used in the ** process, decoration needs to go through, demolition, water and electricity, carpentry, bricklayer, paint, soft decoration these 6 major construction stages, at least 35 basic projects, involving nearly 108 decoration processes......

**It is necessary to see clearly the specific project details, unit price, quantity, and construction technology to see whether the project is complete, the unit price is complete, the quantity is correct, and whether there are variables in the construction. (If you don't understand the decoration at all, you can find a relative understanding of the construction at the same time, for example, whether the water and electricity are all covered in the **, to see and ask clearly that there will be those, what has come out is how much money is a square, to ask clearly, otherwise when the time comes to the decoration, I don't know that so much money is used in the ** process, decoration needs to go through, demolition, water and electricity, carpentry, bricklayer, paint, soft decoration these 6 major construction stages, at least 35 basic projects, involving nearly 108 decoration processes......

There are no sellers at home. As long as you choose the decoration company to install, the pit is certain, but there is a pit, negotiated, don't think it's okay to hand it over, then you have to arrange to go to the construction site every day, shoddy, cutting corners is the consistent style of decoration decoration company, Ann's original contract, the budget of the two houses is less than 120,000, but now it is more than 200,000 or an empty house, the neighbor's two houses are looking for someone to decorate, 120,000 all-inclusive, the furniture is full of house, and I am empty, don't believe in any brand, okay, That's all, I wish you a lot of happiness in your new house and don't be in a hurry to pay, be sure to ask clearly, they told you everything in the early stage, and in the end you will find out that they only pack one or two square meters, and you have to add money if you want to do more, which is the so-called addition. Anyway, keep an eye on it.

Fewer problems. Over time, you will find that there will be odors wafting around the house. And it's hard to get rid of it. Because he'll smell from the hollow tiles.

Because the following has been waterproofed, because there are water stains, the company will complete all the projects with quality and quantity, so when settling the payment, don't settle it all at once! Dividing the payment into multiple times and sub-projects can also ensure the quality of construction to a certain extent.

Yes, we must be present when the renovation company decorates and supervise their work so that they don't become lazy and cut corners.

It's definitely going to cut corners. There is only one way to prevent it, and that is to have a person watching from the scene, so that the renovation workers will not dare to cut corners.

Personally, I think that the decoration company will definitely cut corners when decorating, at this time we must always keep an eye on it, and we must control the quality.