How to connect the wires strongly, and how to connect the wires?

Updated on amusement 2024-07-25
4 answers
  1. Anonymous users2024-02-13

    There are two ways to wiring it below:

    1. Two soft wires are docked.

    First of all, make the two wires into a U-shape, put them in and tighten them, and pull the butt buckle tighter and tighter, then the left wire end is wound to the left, and the right wire end is wound to the right, the winding should be tight and firm to prevent loosening, and finally sealed with electrical tape.

    2. The two soft wires are docked in the middle.

    First of all, divide the two wires into 2 parts, one of them is threaded through, and then the right one is wound to the right, and the left side is wound to the left, until it is tightly and firmly wound.

  2. Anonymous users2024-02-12

    There are three connection methods for wire joints: spiral method, crimping cap connection method, and fireproof adhesive tape isolation method.

    1. Spiral method.

    First, twist the soft wire into a single-strand wire, and then wrap it around the single-strand hard wire, and wrap it around about 7 or 8 times.

    Finally, the single strand of hard wire is bent back and pressed to prevent it from falling off.

    Second, the crimping cap connection method.

    This method is safer, but it requires the use of specialized tools – crimping caps and crimping pliers.

    The operation is very simple, just wrap the wire around the crimping banquet cap, and then tighten it with crimping pliers.

    Third, the fireproof glue Douzhou cloth isolation law.

    This method is mostly used in the ceiling or string lights, and it is not difficult to operate, use the secondary wire to wrap about 8 times around the main line, and then wrap it with fireproof tape.

    The use of fireproof tape is mainly to prevent the outer insulation layer from burning out when the electric fire is burned, and in order to be safe, it is best to wrap several layers of insulating tape on the outer layer.

  3. Anonymous users2024-02-11

    The wire splice method is as follows:

    Tools: wires, main threads.

    1. Tighten the two ends: First of all, you need to twist the two ends of the wire, twist them into a ball, and cross them after screwing.

    2. Tighten on both sides: Then wrap the right one around and make a kickback in the middle of the wrap and tighten it on both sides.

    3. Wrap to the main line: Wrap the left wire around the main line after tightening, and then wrap the right wire around the main line as well.

    4. Wrap the tail: After the cherry blossoms on both sides are wound, the end of the two sides needs to be wound again, so that the wire joints are completed.

    Precautions for wire installation

    1. Pay attention to the correct wiring method when installing the wire, and avoid the joint in the process of installing the wire, if the joint will cause a large resistance, the wire will heat up.

    2. Pay attention to the selection of reasonable installation forms when installing wires, and there are two different forms of concealed and surfaced installation when installing electric oak wires. Concealed installation refers to the laying of electrical wires in places such as ceilings or walls.

    3. When installing wires, pay attention to the correct use of ground wires, such as some household appliances: refrigerators, washing machines and other electrical appliances need to use three-phase plugs, we must pay attention to the installation of reliable ground wires.

  4. Anonymous users2024-02-10

    Hello dear dear, I'm honored to answer for you. There are generally the following ways of wire joints:1

    Stranded wire connection: Strip the two wires to expose the copper wire, then twist the copper and lead wires together, and finally close them with tape or insulating hose. 2.

    Soldering connection: Coating the end of the wire that needs to be connected with a solder core, and then using an electric soldering iron to solder the two wires together at a low temperature. This method is suitable for high-precision and high-load circuit connections.

    3.Snap Connection: Use a special clasp to clip two wires together.

    This method is suitable for temporary connections in the event of an emergency. 4.Terminal block connection:

    Use tools such as terminal holders, pins, and sockets to connect the wires. This method is suitable for connections at higher currents and higher frequencies, and is also the safest and most reliable method. No matter what method is used for the joint, it is necessary to pay attention to ensure the safety and reliability of the joint, and to ensure that Huai has good insulation performance to prevent leakage, short circuit and other safety issues.

Related questions
1 answers2024-07-25

Decorating houses will be designed and installed wires, but there are many types of wires, so it is best to see what methods are available when installing, and it is best to understand when wiring, and the selection of some evil wires also needs to be mastered, thenHome improvement wire connectorsWhat are the methods? What are the methods of selecting and dismantling home improvement wires? Let's introduce it to you. >>>More

12 answers2024-07-25

A high-speed rotary joint, also known as a rotary connection or rotary joint, is a rotary sealing device that connects rotating equipment to a fixed pipe for transporting steam, water, heat transfer oil, coolant, hydraulic oil, air, and other media. High-speed rotary joint manufacturer consultation**: 0519-86180788 Jiangsu Benecke Sealing Technology Co., Ltd. >>>More

27 answers2024-07-25

If you want to fix the wire network cable on the wall cloth and not fall off, then you can fix the whole buckle or use welding glue, which can fix them and will not fall off.

8 answers2024-07-25

According to the cross-sectional area of copper wire, the wire can be divided into different types, but in the specific decoration process, how should we choose? Today we will take the kitchen as an example to explain the choice of wires. >>>More

8 answers2024-07-25

Connecting wires without permission violates the Electricity Law, the Public Security Administration Law and other relevant laws and regulations. No unit or individual shall endanger power generation facilities, substation facilities, power line facilities and their related auxiliary facilities. Connecting power lines without permission will disrupt the normal life of residents, and if the electricity is not used carelessly, it may lead to undesirable conditions such as power outages for residents. >>>More