How to open the glue after the plastic is stuck by 502?

1 Drop 502 in place to melt the original 502, and then quickly wash it off with water, which is very good!

2. With insulating oil, pour the insulating oil in the transformer on the table, and the 502 glue will quickly become soft and can be rubbed off quickly.

3. The same solution can be washed.

502 glue is a kind of resin glue, as long as you use an organic solvent that dissolves the resin, such as acetone. However, acetone is toxic if inhaled, so pay attention to how to use it, and you can stuff the adhesive part into the bottle. It is said that if you freeze it in the refrigerator, the glue will fall off, so you can try it first.

Stick 502 glue on a small area, just soak it in hot water, if a large area is stained with 502 glue, apply acetone, and wait about 5 to 10 minutes to remove.

502 glue is a kind of resin glue, as long as you use an organic solvent that dissolves the resin, such as acetone. However, acetone is toxic if inhaled, so pay attention to how to use it, and you can stuff the adhesive part into the bottle. It is said that if you freeze it in the refrigerator, the glue will fall off, so you can try it first.

Stick 502 glue on a small area, just soak it in hot water, if a large area is stained with 502 glue, apply acetone, and wait about 5 to 10 minutes to remove.

Use banana water to drop on the glue stains, and at the same time use an old toothbrush to stir constantly, until the glue stains become soft and take off, then rinse with water, brush repeatedly, and brush until clean. Put an absorbent cloth on the back of the garment with glue marks, then apply some white vinegar to the glue marks, and finally scrub it clean with cotton dipped in water.

Acetone, gasoline, sesame oil, etc., poured some insulating oil from the transformer on the hand, and the 502 glue quickly softened and finally rubbed off.

1.Soak in hot water below 100 degrees Celsius for several hours.

2.Wash with banana water.

3.Soak it in cooking oil.

4.Soak it in nail polish remover .

I think it's better to wash it with banana water.

I think it's better to wash it with banana water.

Kiss is happy to answer for you : How can something that is stuck with 502 glue get opened? A:

Kiss method 1: This method must grasp the opportunity, that is, it must be used when the glue is not completely dry to be effective. When the glue is just dripping on your hands, quickly put your hands in cold water and soak for a few minutes, at which point you can see that the glue has become a solid, and then buckle the glue off your hands.

Method 2: 502 glue can bond hard objects well, but some of the more flexible ones often have no long-term effect. Therefore, when your two fingers are glued together, rub the glue between the two fingers vigorously, just click on it, mainly to loosen the dry glue.

Method 3: Drop 502 on the original place to melt the original 502, the cured 502 glue will slowly become soft, and then quickly wash off with water. Method 4:

Use the cover to pour some insulating oil from the transformer, and then apply it to the glue part, and the cured 502 glue will soon become soft, and then it can be rubbed off. Method 5: Bring a basin of hot water, stick it to the 502 glue you want to remove with a wet hot towel, and the cured 502 glue will become soft after ten minutes.

Or soak in tolerable hot water for a while and allow the glue to soften. Method 6: 502 glue is a kind of resin glue, as long as you use an organic solvent that dissolves the resin, such as acetone.

But acetone is toxic, so don't use it lightly. Method 7: Use 771 adhesive decombinant for cleaning, which is environmentally friendly, does not hurt hands and materials.

I think it's useful, give it a thumbs up.

502 Jiaosong silver water can not stick to plastic.

502 glue can not be used to stick plastic, plastic is a polyethylene material, not an active molecule, in the process of pasting, it is not easy to produce heat exchange, so it can not play the bonding role of exchange, resulting in the later use of cherry blossoms, there is a situation of falling off.

The correct way to use 502 glue:

1. In the process of using 502 glue, it is necessary to clean up the dust and stains on the surface of the construction surface to ensure the paste effect in the later stage. Under normal circumstances, when bonding metal, it is necessary to carry out grinding work first, and when PE and PP plastic are bonded, it is necessary to activate the surface.

2. When using 502 glue, you need to open the lid of the glue, and use your fingers to buckle the position of the tip so that there will be no residual liquid, and then use scissors to cut out the holes. Then, a small amount of glue drops are placed on the construction surface and then pasted until it is hardened. Note that the bonding area should not be too large.

3. When the 502 glue is used up, the glue bottle needs to be wiped clean, then covered with a lid and placed in a cool, dry area for preservation. Note that if there are children in the family, it must be raised to avoid accidental ingestion by children and unnecessary trouble. <>

Dear, hello, I am glad to answer for you: Can 502 glue stick plastic Answer: 502 glue is not used to bond metal and plastic.

Plastic is a polyethylene material, not an active molecule, in the process of pasting with Huibu, it is not easy to produce heat exchange, so it can not play the bonding role of exchange, resulting in later use, the situation of falling off. In addition, when 502 glue is used, it does not dissolve with the article, but solidifies to achieve a better bonding effect. And when the 502 glue is cured, there will be heat exchange, so as to produce the heat of a reed ear, if the curing time is faster, the sticky and faster will be.

Sticky plastic can be stuck with 818 glue.