-
As long as the wall is ***, you can brush it.
Before the construction of latex paint, the wall must be treated well, otherwise the latex paint will cause serious problems such as falling off, cracking, and blistering after painting. Now many people construction, putty still use 821 putty, in fact, 821 putty is very intolerant to water, when the wall contains water, 821 putty will absorb water and blister, resulting in a large area of latex paint blistering, falling off. And the better the performance of the latex paint, the better the film-forming property, the more serious the problem.
Therefore, when using emulsion, use a back cover to seal the wall and then use water-resistant putty to avoid the above problems.
When the latex paint is constructed, it should be stirred evenly, especially when using brightly colored products, if it is not stirred evenly, when the color paste in the paint is unstable or due to the precipitation of the color paste after long-term storage, then the construction will cause the finish to bloom, which will seriously affect the decorative effect.
In addition, whether water can be added during the construction of latex paint and how much water can be added must be strictly in accordance with the manufacturer's regulations. Because some manufacturers in the design and development of latex paint, has fully considered the various needs of users, designed a variety of formulas, some latex paint in the construction of the construction without water, but the addition of water but the destruction of the various properties of the latex paint.
Note that the brushing, roller coating and spraying process can be used during construction, and any of the above methods can achieve the desired effect, but the viscosity of the latex paint needs to be adjusted, and the viscosity is easy to paint during construction, and there is no obvious brush mark after brushing. If the viscosity is too large, the brush marks are obvious, and the viscosity is low, which is easy to cause slag flow and poor hiding power.
After the construction is completed, the tool should be cleaned with water in time, otherwise after the latex paint is dried, it will be difficult to clean due to the water resistance of the paint film.
Water-resistant putty is waterproof putty.
-
Hello dear, happy to answer your <>
Answer: the white wall of the delivery of the white wall directly painted latex paint is not able to directly brush latex paint, if you go directly to brush, there may be peeling, cracks and uneven conditions after construction, you need to wait until the putty is dry before the wall is leveled construction, but also to repair the potholes, and then brush latex paint. White walls are good ants can not be directly painted with latex paint.
The consequence of directly brushing latex paint on the white wall is that in the later use process, the wall will definitely have problems such as peeling, cracking, and unevenness.
-
Is it okay to paint the wall directly on the big white wall latex paint in the handover, and then brush the latex paint?
Dear, hello, I'm glad to answer for you: Directly in the delivery of the big white wall latex paint brush wall solid, and then brush latex paint OK? A:
If your wall does not have any blistering, peeling, and hollowing phenomenon, it can be used as a preliminary condition for not eradicating the second, and what is the original wall of your house? If it is also latex paint, it can be removed without eradication, but if it is the original white way, it must be removed. Third, whether it is a roller brush or spraying, the impact on the original paint is great, it is recommended that you use a wet cloth with water to stuff the wall for about two minutes, if the wall is still strong and stuffy without any problems, then congratulations you can directly brush again, if it is blistered, then it is likely that the same problem will occur when you spray, in this case it is recommended that you brush the layer of glue will be better Fourth, for how much material to use, you can see the corresponding content in my space, Hopefully, Ant Boy will be helpful to youFifth, it's a big problem, and the materials you use vary greatly.
-
The big white wall cannot be directly painted with latex paint, and the wall needs to be polished before brushing latex paint, and the subtle cracks are polished and smoothed to make the wall in a horizontal state; Paint latex paint on the big white wall, wait until the big white wall is completely dry before painting, the wall is too wet, and the latex paint will crack with the flow of air.
1. Latex paint has film-forming properties, and if the white wall is not treated directly, it will cause the latex paint to bulge and crack, and the dirty places will continue to fall off the wall skin, which will affect the appearance.
2. Before painting, the large white wall should be polished, and the position of the dirt should be paid attention to during the polishing process, and the excessive dirt should be thoroughly cleaned to prevent the latex paint from covering the original stains.
3. Remove all the decorations on the wall, check the holes and cracks on the wall, fill the big cracks or holes in time, and polish them with sandpaper for small cracks. The entire wall can only be painted when it is in a flat state.
4. Latex paint can be sprayed, the speed of painting is particularly fast, and very uniform, all corners can be involved, pay attention to the protection of the floor and furniture when painting, and avoid latex paint splashing on the furniture or floor.
-
After scraping the wall, you can't directly brush latex paint.
Need to wait for putty.
Dry thoroughly and smooth the wall before applying latex paint. Especially in winter, the indoor air is dry, the water loss is fast, and the putty can not be scraped too thickly, and the latex paint should be brushed after it is dry, otherwise it is easy to cause cracking.
In order to prevent dry cracking, you can also put a basin of clean water in each room to increase indoor humidity, which can delay the time for cracks in walls, ceilings, and furniture.
You can't brush it directly.
It needs to be sanded before brushing. The reason is that if the direct brush is not polished, friction. >>>More
Painting walls with latex paint has three flaws:
1. The color is not easy to master, and the color of the appearance will be different from the depth of the actual drying, which will affect the effect of the wall painting; >>>More
To clean latex paint, you need to prepare soap, water, laundry tub, mop, sandpaper, and a small shovel. >>>More
Depending on personal needs, the putty will fall off the powder, and the putty is dirty and not easy to wipe and brushLatex paintIt can solve the problem very well. >>>More
Exterior wall paint is not only colorful, but also its water resistance, pollution resistance and weather resistance are also very good, so now it is more and more liked by the majority of consumers. The construction process mainly includes the following processes: 1. Inspection and recording of the wall substrate; 2. Clean the wall foundation; 3. Deal with wall holes, cracks, etc.; 4. Scrape 1-2 layers of putty on the exterior wall according to the situation; 5. Roller coating alkali-resistant sealing primer; 6. Roller coating varnish; 7. Polishing corners and rough parts; 8. Spraying exterior wall paint; 9. Paste tape into grids at the elastic line part; 10. Elastic wire according to size requirements.