Can speaker wires be replaced with 1 square wire?

Theoretically, there are strict requirements for box cables, and corresponding speaker cables should be equipped according to the different output impedances and powers of power amplifiers. It is the same as how much wire diameter is allocated to the power consumption. Therefore, in addition to the above requirements, you should also choose a special speaker cable with good anti-interference performance.

It is best to use speaker wires, or you can use ordinary soft copper wires for emergency, and it is best to have a larger number of squares, such as more than squares.

Audio has high frequencies, and the more strands of the wire, the better the high frequency performance.

Therefore, the audio cable cannot use a single strand of copper wire, but multiple strands, the more the better.

You can also use wires, soft, and the kind with a lot of thin wires on the skin.

It cannot be used as a wire.

The main reason is that the dielectric strength does not meet the standard of the wire. Some audio cables, even though they are marked with a withstand voltage of 200 volts or 250 volts, have not yet reached the safety factor of the wires. The withstand voltage of the wire should be more than 500 volts.

A wire is a wire that transmits electrical energy. It is divided into bare wire, magnet wire and insulated wire. Bare wires have no insulation, including copper, aluminum flat wires, overhead stranded wires, and various profiles (such as profile wires, busbars, copper bars, aluminum bars, etc.).

It is mainly used for outdoor overhead and indoor busbars and switch boxes. Magnet wire is an insulated wire that generates a magnetic field when energized or induces an electric current in a magnetic field.

It is mainly used for motor and transformer coils and other related electromagnetic equipment. Its conductor is mainly copper wire, which should have a thin insulation layer and good electrical and mechanical properties, as well as heat, moisture, solvent resistance and other properties. Different properties can be obtained by using different insulating materials.

Select Wire Standard:

1. Select copper core wires: wires and wires must first have good conductivity. There are copper core wires and other wires available in the market. Copper core wire is the most practical one for interior decoration. However, copper core wires are divided into several types, including large-radius copper cores and multi-wire copper cores.

2. Wires with strong load capacity: the electricity consumption in the family is sometimes large and sometimes small, and when it is the largest, we will turn on the TV, turn on the air conditioner, turn on the computer, turn on the lights, turn on the water dispenser, refrigerator, hair dryer, etc. If the load capacity of the wire is not strong, and the hot summer is not strong, it is easy for the wire to burn due to the high temperature, resulting in a fire.

3. Good waterproof performance. The appearance of some wires is easy to deform and crack, in case there is a water leak somewhere, then it will cause the electrical appliances to burn out, short circuit and even cause fire and personnel**. So be sure to have a hard outer skin and a good waterproof wire.

4. The main line must be a thick core. The so-called main line refers to the two main lines between the total power supply and all electrical appliances. The main line ratio must be made of thick copper core wire, because the main line is loaded with the charge of each electrical appliance, and the thick copper wire with excellent performance is required. Multi-core wires are available for bypass.

Yes, but the power of the connected electrical appliances should not be too large, so as not to melt the wires.

Of course you can!

It's just that the cost is a bit high.

Yes, both are wires, and from a circuit (electronics) point of view, they can build an effective circuit to transmit the audio signal. But it should be noted:

1. It must have an impact on sound quality and volume, the functions of these two products are different, and the trait indicators are also different;

2. The speaker line has small resistance and high power, which is easy to heat up and burn because the power is too small.

First of all, the material it uses is relatively pure, the resistance is relatively small, and the loss of audio current is relatively small; In addition, the wires used to transmit audio current should be absolutely parallel, and the electromagnetic interference generated is relatively small.

The above requirements for ordinary wires are not too strict, and the requirements can be reduced according to the cost.

OK. However, the use effect is not as good as that of the audio cable, because the resistance value of the audio wire is lower, while the resistance value of the ordinary wire is higher.

The transmission path cannot guarantee the distortion required by the audio system, and the reliability of the connector cannot meet the distortion index. Therefore, the use of audio cable instead of ordinary power cord, the impact on the ordinary power cord is sure and obvious, in the case of good connection, the cable is used for power transmission, a distance of a few meters will not have obvious power attenuation.

Can the speaker wire be replaced by an ordinary wire, the speaker wire can be replaced by an ordinary wire, but the use effect is not as good as the speaker wire, because the resistance value of the audio wire is lower, and the resistance value of the ordinary wire is higher. Audio wires are usually coated with an additional layer of tin on the surface of the copper wire, which reduces the resistance value. The speaker system refers to the use of a microphone to convert the sound wave signal of the original sound field sound into an electrical signal, and according to certain requirements the electrical signal through some electronic equipment processing, and finally use the speaker to convert the electrical signal into a sound wave signal for replay, this process constitutes a speaker system.

The speaker line is used to connect the power amplifier and the speaker, in which the current signal of circulation is much greater than the aforementioned ** line and audio line, because the signal amplitude is very large, this kind of line often has no shielding layer, for this kind of wire, the key is to reduce its electrical resistance, because the output impedance of modern power amplifier is very low, so the requirements for the speaker line also increase, such as the selection of large cross-sectional area or multi-strand stranded wire. The function of the speaker cable is to connect the speaker components to transmit the audio signal and the best signal. The characteristics of the intelligent signal line are that it is divided into two channels according to the signal frequency, and the outer line of a certain thickness is transmitted through the inner layer of the line through the signal below 5kHz, which greatly improves the frequency characteristics of the transmission line and makes the sound of replay clear and transparent.

<> "When arranging household appliances, special attention needs to be paid to avoid affecting the normal use of the later stage, such as the sound line to choose the right one. And can the audio cable be replaced by a normal wire?

Can the audio cable be replaced by a regular wire?

Yes, if there is no matching audio cable, you can use ordinary wires instead, but the overall effect is not as good as the audio cable. The resistance of the audio line is small, and the resistance of the general wire is large, and the use of the general wire will cause the transmission line to not ensure the strain standard required by the audio system, and the reliability of the connector can not meet the strain standard.

What to look for when choosing a speaker cable

1. When choosing an audio cable for the first time, it should be selected according to the quality and level of the speaker itself. High-quality Jinye stove audio is very particular about power supply, sound source, tuning, etc., as long as there is a little difference, it will give up the previous job. Therefore, for a good sound, please choose a high-quality speaker line.

Conversely, choosing high-quality surround sound will not improve the sound quality of low-end sounds.

2. In addition, when purchasing an audio cable, please purchase it according to the power of the speaker. It is said that the thicker the audio cable, the better, but after actual use, it is found that too thick audio cable will cause unnecessary waste. Choose a speaker with more power than the horn.

3. When buying audio cables, you need to purchase them according to the location where the audio is placed and the distance from the machine. Once determined, it is advisable to leave a margin of 50 cm for measurement, which should not be too long. Audio cables aren't cheap, so cutting it out is a great waste.

If you don't cut it, it will take up special space.

4. In addition, when buying audio wires, if you buy a transparent insulation and copper material, the spine group will discuss the family to buy 200 copper cores, and if the audio power is large, you can buy more cores. In addition, the manufacturer of the ** core will be confirmed. Must be a qualified manufacturer.

Summary: If there is no matching audio cable, you can use ordinary wires instead, but the overall effect is not as good as the audio cable. The resistance of the audio line is small, while the resistance of the general wire is large.