Is it safe to stick tiles on top of the beams

It is not advisable to lay tiles on beams, as it is not safe.

First of all, the beam is an important supporting component in the structure of the house, and if the tile is paved on the beam, it may adversely affect the load-bearing capacity of the beam and reduce the stability of the house.

Secondly, the tile itself also has a certain weight, and if it is paved on the beam, it may increase the burden on the beam, resulting in a decrease in the bearing capacity of the beam. In addition, the shape and structure of the beam may also affect the paving effect of the tile, if the surface of the beam is not smooth or there are protrusions, depressions, etc., it may cause the tile paving to be not firm and easy to fall off.

Therefore, if you want to do interior decoration, it is better to choose other methods to lay the floor, such as floor paint, flooring, etc. This can ensure the safety and stability of the house, and at the same time can also improve the aesthetics and comfort of the interior decoration.

The situation you mentioned is more common in the kitchen and at the entrance of the kitchen balcony.

In the case of not installing the door sleeve or door, the lintel at the top of the pass can be said to have to be tiled in order to maintain the appearance.

For this case, the standardization of tile construction is very important. Suggested Solution:

1. If there is gypsum putty on the top of the lintel.

It needs to be removed;

2. Base roller brush interface agent.

After the use of cement mortar.

Smoothing and then brushing;

3. After the brushing layer is dried and solidified, the dry brushing layer is sprinkled with water and moistened before tiling;

4. Add some glue (or wall shovel) to the cement mortar for pasting tiles to increase the adhesion of the cement mortar.

You can tile the beam above the balcony window.

When pasting tiles, the cement should be placed a little full, and the amount of cement around the surface of the tile is about the same, so as to ensure that the tiles are firmly glued and will not be hollow.

After paving, use a special small hammer to hit the surface of the tile to detect whether it is hollow.

The tile must be pasted flat, after pasting, the experienced master will use a plastic hammer to beat the tile around, and control the surface flatness of the tile in time. Otherwise, it will be too late to adjust the cement when it is dry.

Ceramic tiles are indispensable building materials for our home decoration, which not only look smooth and beautiful, but also easy to take care of. Some friends asked if it was possible to put tiles on the interior beams. So what is the method of tiling under the beam?

It is usually not recommended to lay tiles at the lintel, but if you have to pave them, you must remove the putty plaster from the beams to expose the cement bottom layer. Then the bottom surface of the cement is sprayed wet, and the cement slurry is used for brushing, and the tiles can be paved only after drying. After the tile is pasted, the bottom of the branch needs to be covered with a wooden square, otherwise it is easy to cause it to fall off.

What are the precautions for tile paving:

1. The walls should be wet with water.

If you are laying tiles on the walls of the living room balcony, it is best to wet the wall 24 hours in advance, and it is best to soak it to a saturated state. Because this kind of wall does not need to be waterproofed.

2. The tiles should be soaked in water.

When laying tiles, it is best to completely soak the tiles in water in advance until the tiles do not bubble in the water, which generally takes about half an hour. Don't simply spray some water on the tiles for convenience.

3. Leave gaps when posting tiles.

When paving tiles, it is also necessary to pay attention to the reservation of a certain gap between the tiles, because the tiles have the characteristics of thermal expansion and cold contraction.

4. When posting wall tiles, you need to use wall tile clips.

If you pave the wall tiles, you also need to use the wall tile clip, which is a professional matching, which can well adjust and fix the distance between the tiles, so that it is horizontal and vertical.

Summary: The above is to introduce you to the beam under the tile method is what is the relevant content and what are the precautions for tile paving, I hope to help friends in need, if you need to know more about the relevant knowledge in the later stage, welcome to pay attention to Qeeka Home information.

1. It is usually not recommended to lay tiles at the lintel.

2. But if the limb has to be paved, the putty gypsum on the beam must be removed to expose the bottom layer of cement.

3. Then spray the bottom surface of the cement, use the cement slurry to do brushing treatment, and only after drying and solidifying can the tiles be paved.

4. After the tile is pasted, the bottom needs to be covered with a wooden square, otherwise it is easy to cause it to fall off.

1. It is usually not recommended to lay tiles at the lintel.

2. But if you have to pave it, you must remove the putty gypsum on the Liangzu sail and expose the bottom layer of cement.

3. Then spray the bottom surface of the cement, use the cement slurry to do brushing treatment, and then pave the tiles after drying.

4. After the tile is pasted, the bottom of the tile needs to be covered with a wooden square, otherwise it is easy to cause it to fall off.

Summary. Hello dear. It's safe for a short time, but it's dangerous after three or five years. So it is recommended not to post.

Hello dear. It's safe for a short time, but it's dangerous after three or five years. So it is recommended not to post.

Ceramic tile is a kind of acid-alkali resistant porcelain or stone formed by the process of grinding, mixing, pressing, glazing and sintering with refractory metal oxides and semi-metal oxides, and is called ceramic tiles. Its raw material is mostly made of clay, quartz sand, and mixed with high temperature after pressure and shrinkage, etc., with high hardness.

The history of ceramic tiles should be traced back to BC, when the Egyptians began to decorate various types of houses with ceramic tiles. Clay bricks are dried in the sun or baked and then colored with a blue glaze extracted from copper. Ceramic tiles were also found in the Mesopotamian region BC.

This type of tile was decorated with blue and white stripes, and later appeared in a variety of styles and colors. During the medieval Islamic period, the method of decoration of all tiles reached its peak in Persia. Subsequently, the use of ceramic tiles gradually became popular all over the world, and in the history of ceramic tiles, Spanish and Portuguese mosaics, Italian Renaissance floor tiles, glazed tiles in Antwerp, the development of Dutch tile illustration and German tiles are all milestones.

The most common technique for retouching beams is to use a shape wrap to hide or divert the attention of the eye. For example, the arc wrapping shape can reduce the feeling of oppression of the beam.

Circular transition design.

The beams located above the head of the wall are often decorated with arc cladding. Care must be taken to match the size of the beam to make the entire arc line softer and smoother.

Arc wrapping design.

If the position of the beam is more obvious and the depth is not particularly large, it can be completely covered with an arc to reduce the drop and compression around the beam, so that the lines of the ceiling are smoother, and the beam can be easily blurred.

Arc cladding + indirect light source.

The irregular ceiling design, arc wrapping and supplemented by indirect light sources, make the small space also have rich visual levels. Follow the moving line with an arc to resolve the oppression of a small space. It can not only achieve the effect of decorating beams and columns, but also hang hidden air conditioning.

The beam tile is not easy to fall, and in this case, the standardization of tile construction is very important. Suggested Treatment: 牋.

1. If there is gypsum putty on the top of the lintel.

It needs to be removed; Mul.

2. Base roller brush interface agent.

After the use of cement mortar.

Smoothing and then brushing; Mul.

3. After the brushing layer is dried and solidified, the dry brushing layer is sprinkled with water and moistened before tiling; Mul.

4. Add some glue (or wall shovel) to the cement mortar of the tile to increase the cohesiveness of the cement mortar, as long as the coating on the surface of the beam is removed with a tool to expose the cement. Mul.

5. Finally, the tiles can be paved, which can ensure that the beams are tiled and not easy to fall.