How to make a simple shape of a long balloon, make a long balloon shape

We often see all kinds of balloons used for decoration in the market, and today we will talk about how to make a balloon shape by yourself.

How it works:

To make a balloon shape with flower petals, you need to prepare a long balloon with a diameter of 2 inches and a length of 60 inches when inflated.

Inflate the long balloon first, and leave about 4cm at the end of the balloon without inflating.

Fold the long balloon in half from the middle part, and tie the balloon and tail part together using a knot method.

Pinch the two balloons together near the middle folded one-third, twist another one-third to make it into three sections, and then place the three rings side by side.

After placing them side by side, grasp both parts with the twist points facing upwards with your hands.

Then the other hand presses each ring from the bottom up to the point corresponding to the pinching place, so that one ring is pressed in half to make two petals, for a total of three rings, so that six petals will be formed.

Twist the left and right petals in the above picture toward the center point to separate the shape of each petal, and after fixing it, the balloon in the shape of the petals is made.

We can also make a balloon in the shape of a puppy.

Inflate the balloon, leaving a three-inch tail. Continue blowing until the air expands and the tail end remains about three inches, then stop blowing and tie the balloon in a knot.

Make three basic twists. Starting with the knotted part of the balloon, make three basic twists, so that the balloon has a total of four parts. The first part, including the balloon knot, forms the dog's nose.

It is longer than the other two segments, which can form a dog's ears. The last segment is the longest and will be used to make the dog's body.

Hold these segments with one hand to prevent them from letting go, as they are not yet locked.

Twist the ear parts together. Use your free hand to grab the ear parts of the second and third segments and twist them together three times.

Make the other three basic twists. Make the first twist a few inches at the lower end of the head to form the neck. Make two twists below the neck so that the two parts are equal in length, which will form the legs. Use the same hand to hold the freshly folded parts to prevent them from coming loose.

Twist the legs together. Twist the middle part of the legs, grasp the legs with your free hand, and wrap them together using your neck as a base. Now the legs and neck are locked in place.

Make the other three basic twists. This time, the rest of the section is divided into four sections of equal length. The first segment is the dog's body, the two parts of the second segment are the dog's retreat, and the last part is the tail. Hold them in one hand to prevent them from coming loose.

Twist the hind legs together. Twist the part between the two hind legs, grab both legs and twist them three times on the basis of the body part, and look at the balloon shape you complete: it has a knotted nose, short ears, front and hind legs, and a straight tail.

The steps are as follows:1. Prepare the required materials: 2 260 long balloons.

2. The yellow balloon is inflated to a length of about 3 cm at the end of the remaining end.

3. Fold the balloon in half, and fix the air nozzle and the remaining end knotted together, so that the balloon becomes an end-to-end ring.

4. Adjust the knot to the ** position of the balloon and twist it to make it two rings.

Long Balloon Modeling Tutorial - Strap Doll:

Take out 5 long balloons and pull them. Inflate with a pump, leaving 5-8cm at the tail to screw together the 17cm bubbles of the pink balloon with the 3cm bubbles of the blue balloon.

Take out two balloons and screw them on both sides of the doll's body, as a doll's strap, fold the inflated balloons evenly in half, and pass through the middle of the doll's body as the doll's legs.

Fold the second bubble in half and twist it together, then stuff the first bubble into the folded bubble. Take out a smiley balloon, and after it has been inflated, twist it in the place where the leg is folded in half. Then adjust it so that your head and body are in harmony.

Fold it in half twice and twist it in the middle to form a flower shape as a headdress.

Screw the headgear together with the middle of the top of the smiley balloon.

The long balloon modeling tutorial is as follows:Material preparation: long balloons.

Operation steps: 1. Make the simplest leaves first. Pinch two circles at the top of the green strip.

2. Fold in half again. The remaining strip is 1/3 of the length and twisted.

3. Then take the remaining 2/3 and take 4, Pei Li Jin 5cm long and fold it in half. The other side is also folded up. Such simple leaves would be fine.

4. Take the length of cm at the top and pull the matching base head down and fold it in half.

5. Then fold the top and fold 5 flowers along the way.

6. Finally, just combine the two, there is a hole in the middle of the flower, and the head of the leaf is stuffed into it.

The long balloon twisting love tutorial is as follows.

Tools Ingredients: long balloons, pumps.

1. First of all, you must inflate the balloon to the end, you don't need to leave a small tail like when making other balloon shapes, remember, it's not like the picture below.

2. Then we bend the balloon, bring the two ends of the balloon together, and twist them together when it is almost 2-3 cm to the end. In this way, a circle will be formed, which is a bit like love? Here, I would like to remind you that it is best to leave about 2-3 cm at both ends of the balloon to extend outward, the first is that it is easier to twist, and the second is that it will look better, otherwise it will look too lifeless.

3. Then you will find the midpoint of the opposite side of the intersection with the end, take a section on the left and right sides of the midpoint, and pinch them together with your hands. If you pinch it hard like this, hold it for a while, and it will form a curved shape. This step will take you a few times to try on your own, but generally speaking, the longer the part you pinch, the greater the curvature will be, and the shape of the heart will be more beautiful.

4. As soon as we let go of our hands, a super perfect balloon is formed.

Whether it's a wedding room decoration or a wedding scene decoration, balloons are a good decoration item. And when you get married, you can use balloons to decorate, and love is a good way to place it.

Here's how:Material tools: long balloons, pumps.

Steps: 1. Inflate the balloon first, and then tie the knot. The tail is about four centimeters long.

2. Twist a small balloon on the head of the balloon, then hold the first small balloon and twist out a small balloon that is larger than this one.

3. Then twist out a balloon that is larger than the previous small balloon, and then twist a balloon that is larger than this one. If you are afraid that the three small balloons in front of you will scatter, you can wrap them around them with a small rubber band.

4. After making four small balloons, twist out the fifth one. The fifth one should be the same size as the third, and the sixth one should be the same size as the second.

5. Twist the second balloon and the tail of the balloon together, and remember to leave the first balloon out.

6. Flip the first small balloon to the back of the circle.

7. Press the small balloon on the top of the circle with your hand.

8. Twist the small balloons on the left and right a few times to make the ears of the bears.

9. Now turn the small balloon that has been flipped to the back and make a roaring nose.

10. Leave the balloon about three centimeters below the bear, and then twist the bow shape left and right.

11. Hold the bear in your hand and you're done.