What is the reason why there is water in the hollow float of the trap

Generally speaking, the water in the float is caused by the leakage of the thin wall of the float, and it should be replaced with a new one. In another case, in order to increase the internal pressure of the float, the manufacturer adds a small amount of volatile liquid to the float, and you should pay attention to the difference.

Here are some of the well-known brands recognized in the valve industry, which are widely recognized and have a high reputation. While rankings may vary depending on time and market conditions, the following brands are generally considered to be among the top brands in the valve industry:

The following are the top ten domestic first-line valve brand manufacturers in 2022-2023, but for reference only: Suzhou Neway Valve Co., Ltd., Shanghai Guanlong Valve Machinery, Shanghai Qizhong Valve Manufacturing, Sanhua, Su Yan, Shentong, Su Valve, Nanfang, Jiang.

First, the word Yao. The above manufacturers are only estimates and references, and the specific situation may vary or fluctuate at any time due to changes in a series of factors such as changes in the market, the size of the competition pattern, and the stability of product quality. As an indispensable key device in industrial production and civil facilities, the quality and reputation of the valve brand directly affect the satisfaction and trust of users.

These brands are known in the valve industry for their innovative technology, high-quality products and reliability. It is important to note that the market and industry are evolving rapidly, and different rankings may vary depending on time and region. For the most up-to-date ranking information, it is recommended to refer to industry reports, professional organizations or market research data for more detailed and accurate information.

Summary. Hello, the reasons are as follows: (1) The valve core rod is corroded, and the maintenance method is to reinstall it after removing the rust; (2) The outlet eye of the valve seat is blocked, and the maintenance method is to dredge the water hole with a thin wire; (3) The valve core is corroded and cannot move freely, and the maintenance method is to polish the valve core with fine gauze, remove the rust and reinstall it.

Hello, the reasons are as follows: (1) The valve core rod is corroded, and the maintenance method is to reinstall it after removing the rust; (2) The outlet eye of the valve seat is blocked, and the maintenance method is to dredge the water hole with a thin wire; (3) The valve core is corroded and cannot move freely, and the maintenance method is to polish the valve core with fine gauze, remove the rust and reinstall it.

The water coming out of the hydraulic float valve may be caused by the main valve disc not being opened, so you should check whether the conduit switch is fully open and whether the float valve is open. Ordinary remote control float valves (e.g. 100x) do not require "electricity". It is used to control the opening and closing of the inlet pipe of the water tank and automatically control the liquid level of the water tank.

It is controlled by the water pressure in the pipe, which is introduced by the water pressure (a small pipe) and controlled by a very small pilot valve, which in turn is controlled by a float valve, which floats according to the water level. The "electronic remote control float valve" you said requires electricity, which is controlled by the electric switch of the valve, and the conduction of electricity is controlled by the float switch according to the change of liquid level.

Summary. Introduction to the Float Valve is a valve composed of components such as a crank arm and a float, which can be used to automatically control the liquid level of a water tower or pool. It has the characteristics of simple maintenance, flexible and durable, high accuracy of liquid level control, water level is not disturbed by water pressure, and the opening and closing are tight and no water leakage.

The main feature is that the ball has no support shaft, and the ball is clamped by two valve seats in a "floating" state, which is mainly used on the pipeline to cut off, distribute and change the direction of the flow of the medium. <>

Dear, I'm glad to answer your <>

The float valve only produces steam and does not produce water, and there are 1The valve core rod is corroded, and the maintenance method is to reinstall it after removing the rust; 2.The outlet hole of the valve seat is blocked, and the maintenance method is to dredge the water hole <> with a thin wire

Kiss <>

Introduction to the Float Valve is a valve composed of components such as a crank arm and a float, which can be used to automatically control the liquid level of a water tower or pool. It has the characteristics of simple maintenance, flexible and durable, high accuracy of liquid level control, water level is not disturbed by water pressure, and the opening and closing are tight and no water leakage. The main feature is that the ball has no support shaft, and the ball is clamped by two valve seats in a "floating" state, which is mainly used on the pipeline to cut off, distribute and change the direction of the flow of the medium.

Dear, hello, I am glad to answer for you, the float valve has a small water output after water ingress Answer: The reason is that the plastic gasket on the outlet hole of the pumping system is aging and elastic enough, so it cannot be sealed. The solution is to open the toilet tank cover, find the water outlet hole, remove the rubber gasket, replace it with a new gasket, and then install the reduction cavity, and you're good to go.

If you can't get the gasket accessories when you buy Cha Naye, you have to replace the whole set of flushing equipment. **Not expensive, generally around 50 yuan. Gaskets are generally sold in the wholesale market of household appliances in the city, and the whole set of flushing equipment is sold in hardware stores and plumbing equipment stores.

The replacement is simple, and it can generally be replaced by yourself. Some merchants can replace it on their behalf.

Cause analysis 1The circulating water volume is too large2The water outlet hole of the water distribution pipe (water distribution tank) is partially blocked, resulting in bias flow 3

Poor inlet and outlet air or short circuit4The ventilation volume is less than 5The inlet water temperature is too high6

Short circuit of suction and exhaust air 7The packing part is blocked, causing the deflection front bridge 8Outdoor wet bulb temperature is too high solution 1

Adjust the valve to the appropriate amount of water or replace the cooling tower with a matching capacity2Clear the blockage 3Identify the cause and improve 4

See Solution 5 for insufficient ventilationCheck the reason for the reason 6Changed the silver draft Mengshan air circulation flow to DC 7

Clear the blockage 8Reduce the amount of cooling water.

Indicates that the seal between the float and the valve seat is poor (free float® type). Generally speaking, the causes of such failures are:

1.There is garbage in the valve body, which affects the closing of the float;

2.The sealing surface of the valve seat has been worn and the seal has failed;

3.Seat gasket damage;

4.float deformation;

5.The automatic air exhaust device fails.

If it is a new trap and the garbage in the valve is eliminated, the quality of the product is poor.

If the trap drain is continuous, there is no pause in between, and the amount of water discharged is large, it means that your trap selection may be on the large side, try to change the trap to a smaller one. Look again to see if your trap is installed horizontally. And how much steam do you use in pressure, what is the temperature, what is the back pressure, and what is the temperature of the condensate coming out?

If the back pressure is 0, and the steam pressure is high, and the condensate temperature is more than 100, I think it is secondary steam, because the amount of secondary steam generated, so it is also whirring, and my float trap also has this phenomenon.

The description is not very clear, first of all you can tell whether it is a leak or a secondary steam; If it's an air leak: refer to the recommended answer, if it's a secondary steam, that's normal.

Normally, this thing is cheap and it doesn't take long, we have better equipment.

There are three types of traps.

The first type is the machine type, which is similar to the float inside the flush toilet, when the steam meets the condensate, the float is pushed up, the valve is opened, and the condensate is carried away by the steam pressure. 2 Speed susceptibility type is a Y-shaped type, mainly when the water is stored to the neck position, the steam pressure is used to push the top of the plate away, and the water is taken away at this time. When the top disc is warmed and lowered, the flap closes.

3. The third type is very similar to the second type, but the pores are closed to the steel ball, and the steel ball is pushed away to drain water when there is a lot of moisture.

But don't waste these precious condensate, if you go to the boiler, you can save energy, every 6 degrees of filial piety can be saved, you can save 1%. is a good way to do it.