If you want to make the floor tiles more overall effect, what method should you use to paste the flo

What is the easiest way to change the color of the tiles, if you want to change the color of the floor tiles, you can modify it according to the specific content and plan, these problems are required to ask professional people to carry out the construction, and you can't do it casually. How to build gray floor tiles, gray floor tiles look at a large area of black as the keynote, the dragon transformation with the wind and rain is also lightning, the horizontal line of white lines is like a white dragon shuttling through the clouds, the layers are clear, atmospheric and smart, it is the spirit of the black stone.

<> the usable area of general ceramic tiles is relatively large, so we must pay attention to the overall visual presentation in the selection. Solid color tiles have a relatively clean and simple visual sense no matter which area they are used, which makes people feel very good. Compared with the bathroom, the color bricks used in the kitchen pay more attention to the wholeness, especially those with an open layout kitchen design.

It's designed to have a subtle impact on other spaces. Colored tiles can be laid with a small surface to set off a large surface.

Modern living rooms are increasingly focused on the creation of simplicity, atmosphere or special style, and ceramic tiles are used in a large area in this process. From floor paving to wall decoration, tiles are everywhere. When purchasing, consider the size of the specifications according to the size of the area, and when we pave the tiles in the appropriate room, most of them will use the ground pressure wall paving method, and it seems that there is little difference between the kitchen, but it is different when it comes to the bathroom.

If we didn't decorate it well when we renovated, or we used this method of tiling.

Corner upturned or concave will affect the quality of paving, whether the tile pattern is natural and beautiful, whether the pattern is blurred, glaze gloss brightness, are the standard for choosing a good tile, if you want to look good in the room space is sufficient, it is recommended to do a modeling, the quality of tile selection is better than this green in color, but it is difficult to match with the tile tone, and it is not very in line with people's aesthetics. Therefore, glare green is a cool color for the time being in the use of beauty sewing, and it is not widely used.

You can use a tight method to stick to the floor tiles, because this method is that each floor tile is close to each other, and there will be no gaps, and the overall effect will be better.

Stick the floor tiles from the middle to the edges, and then cut off the excess areas, so that the integrity will be stronger and it will look beautiful.

You can paste floor tiles behind the TV background wall, which makes the effect look more three-dimensional, and will make the floor tiles display very beautiful, and enhance the atmosphere of the home.

The general method is: first use river sand 2 + cement 1 to lay the base. Add less water!

Printing plates with large bricks. It is to use clean floor tiles to lay the bottom layer first and use a rubber hammer to knock it down, knock it flat, and put it right. Then remove the bricks, add a small amount of pure cement grout (or tile glue) to the back of the bricks, and then paste them.

You can put some locators, and after these positions are set, you can spread the floor more neatly.

1. There are 5 ways to stick floor tiles on floor tiles. Fishbone Patching: The fishbone tiling method is named because the paving effect resembles the bones of a fish, which is actually a combination of the 45-degree collage method and the diamond-shaped collage method.

2. Human-shaped early bright silver spelling: The human-shaped collage method is somewhat similar to the fishbone collage Lu Yan, but there is a little change in the treatment of the corners, the fishbone method is smoother, and the human-shaped law has edges and corners.

3. Oblique column spelling: The oblique column paving method is a variant of human-shaped paving, and the main difference is the angle change when paving, and the oblique column method is more obvious.

4. Roof ridge spelling: Roof ridge paving method, as the name suggests, the paving effect is like a roof ridge, with a very obvious sense of concave and convex.

5. M spelling method: M-shaped paving method is a paving method that combines human-shaped paving method and symmetry method, and the sense of pattern key preparation is stronger.

2. Align the floor tiles on the cement mortar and beat it tightly with a hammer.

3. Remove the floor tiles after knocking, and then leave the pattern on the back of the floor tiles on the cement mortar. The master said that this step is the key to preventing hollow drums. There will be some small cavities left on the cement mortar after hammering, indicating that the cement mortar in these small cavities is not enough, and if the floor tiles are pasted, it is possible to form hollow floor tiles in the future.

So the master dipped in some cement mortar to fill these holes, and then covered the floor tiles again and knocked them hard, so as to ensure that the floor tiles were completely compact.

Fourth, the master then removes the floor tiles and evenly smears cement on the back (note: pure cement is used here instead of cement mortar!). Because the pure cement is more viscous), and then put it back in its place, and there is another beating, so that the paving of a floor tile is completed.

Sweat.. The buddy upstairs said... That's too much. Honestly, the idea is right, but if you do it as he says. If you can stick a brick, I will worship him as a teacher.

It is recommended that you go to a master, these things can be done by talking, and you have to learn on the spot! (Provided you want to do what we do).

Dry paving method 2Wet paving method 3Wave line laying method 4Traditional paving.

Kitchen and bathroom walls and floors, regardless of the type of tile, can be directly applied to the old tiles with new tiles.

First of all, it is necessary to remove the dust and dirt on the surface of the old tile, and then use the tile adhesive to do the base layer on the old tile, and the new tile can be directly pasted after the batch is completed. The adhesive should also be applied thin on the back of the new tile, and the thickness should be subject to the back pattern of the covered tile, so that the new tile will be more firmly glued.

When paving new tiles, use a rubber hammer to tap the new tile edge to adjust the edge, you need to pay attention to the reserved expansion joint, 24 hours later, wait for the tile adhesive to dry thoroughly, and use the grout to hook the joint. With the right tools, consumers can do their own DIY.

Tips: Individual seriously bulging or damaged tiles need to be removed, after shoveling, repair with mosaic surface tile surface treatment agent, and after the surface of the old tile is as smooth as the old tile, then paste the new tile with tile adhesive, which is more firm.

1. Straight line laying.

Advantages: decent and generous, simple and neat. Let the appreciators feel the strong texture of the floor tiles.

2. I-shaped paving.

Advantages: Generally, those who like the I-shaped paving method are young people who pursue novelty. There is a refreshing feeling with this method, and the I-shaped paving lines are beautiful. It's also a good choice.

3. Diagonal paving method.

Advantages: The straight line is very smooth, there is a feeling of infinite extension, and the visual impact is extraordinary. It is also one of the commonly used laying techniques.

4. Group assembly paving method.

Advantages: This paving method uses large and small floor tiles to match, with clear patterns and rich patterns. Most of them are used for corridors, living rooms, dining rooms, and entrance entrances as key designs.

We are familiar with the floor tiles used in every home, but do you know what the specific skills are for attaching floor tiles? PChouse will take you to find out.

1. Ground leveling: Before laying floor tiles, it is necessary to measure with a level and level the ground, and it is best to use cement mortar to pave the ground, which can reduce the appearance of tile hollowing. Finally, the floor that needs to be paved with floor tiles is made into a rough base, which can increase the stability of the tiles that are paved.

2. Pay-off: Before paving the floor tiles, the floor tiles should be pre-discharged according to the ground size and the size of the floor tiles, the principle is: in the same room, the horizontal and longitudinal half of the floor tiles can not exceed one line, and half of the bricks should be left on the side of the furniture or an inconspicuous place in the future.

3. Ground cleaning: Before the tile is paved, clean up the bulging and adhesive on the ground and wall, and sprinkle some water if necessary, and the humidity is guaranteed to be 30% 70%, which can prevent the tile from hollowing.

4. Tile soaking: because there are many small voids inside the tile, these gaps have a certain degree of water absorption, if the floor tile is not soaked in water, the moisture in the cement will be sucked away, resulting in a gap between the tile and the cement, which will cause problems such as hollowing and tile falling off.

5. Test paving, leveling and tamping of the base layer: whether the floor tiles are hollow, this step is very important, and it must be tamped, and at the same time, workers should check whether there is an error between the corners of the floor tiles and the adjacent floor tiles.

6. Floor tiles are back ash and paved floor tiles: a layer of plain cement plaster should be smeared on the back of the floor tiles as an adhesive layer, and the thickness should not be less than about about that, and the application must be uniform and not missed. Paving floor tiles, to use a rubber hammer to evenly beat, adjust the level with the horizontal line and other floor tiles and the size of the gap, if there is a condition to use a horizontal ruler to check whether the tiles are level, with a rubber hammer to beat until completely level.

Confirm the specifications and dimensions of the floor tiles. This is a very critical step. If we want to design the floor paving, we must first choose the floor tiles that are suitable for the specifications and sizes.

For example, the living room is generally paved with 800mm 800mm, or 600mm 1200mm, or 750mm 1200mm to the floor tiles. We can choose the right floor tile from these specifications.

Typography of floor tiles. After we confirm the specifications and dimensions of the floor tiles, we can carry out the typesetting. When typography, we first need to measure the length and width of the room, as well as the location of the specific doorway, and then we can use the size of the floor tile we have chosen to typeset indoors.

When typography, be sure to consider the gaps between the floor tiles. Personally, I suggest that we lay floor tiles in the living room, generally leaving a gap of 2mm. The part that connects with the wall can be left a little more, such as leaving a gap of 5mm.

In turn, the floor tiles can be typeset in our room.

2): Test paving before tile paving.

According to the design and size of the floor tiles, as well as the typesetting, we can carry out the paving of our floor tiles. Before laying the floor tiles, we must first choose the starting position of the paving when laying the tiles. Because the choice of starting position also determines the specific size of the floor tiles that will be paved later.

Therefore, I personally recommend that you follow the following steps.

Selection of the starting position. The choice of the starting location of the indoor floor tiles varies depending on the room. For example, in the bathroom, it is recommended that you lay the first brick from the innermost side of the bathroom, and then lay it outward.

For the living room or dining room, it is recommended that you pave from the balcony to the entrance door. For the kitchen, lay from the inside of the kitchen to the outside, so that we can confirm the position of the first brick.

Test shop. The so-called trial paving is to dry code the floor tiles on the ground to confirm the specific size. For example, when we lay the floor tiles in the bathroom, we first stack the first floor tile on the ground, then dry the floor tiles on the ground in turn, and finally go to the door.

This makes it possible to find out exactly the size of the half brick that appears on the floor of our bathroom. Of course, this step can be omitted if our layout is very accurate. But if there is no layout drawing, then it is recommended that you try to find the location of the last brick and a half.

The method of sticking tiles and sticking to the wall instrument to quickly fix it on the wall, have you learned it?

1.Prepare tools and materials: floor tiles, tile adhesive, tile cutter, level, plumb line, rubber hammer, tile cutter, tile pliers, stool marker, broom, mop, etc.

2.Clean the ground: Clean the ground to ensure that the ground is flat, dry, and free of oil, dust and other debris.

3.Tie the line: Use the plumb line and the wire tapper to make the brick seam line on the ground, making sure the brick seam line is straight and vertical.

4.Gluing: Apply the tile glue evenly on the ground, be careful not to apply too thick or too thin, so as not to affect the pasting effect of the bricks.

5.Paste the tiles: Paste the tiles on the ground according to the brick seams, pay attention to the gap between the tiles to be consistent, and use a rubber hammer to gently tap the tiles to ensure that the tiles fit tightly with the ground.

6.Cutting tiles: If you need to cut tiles, you can use a tile cutter or tile cutter to do it, pay attention to safety.

7.Caulking: After all the tiles are pasted, use tile glue to fill the brick joints, and then clean them with a broom.

8.Finishing: After the tile glue is dry, clean the ground with a mop to ensure that the ground is dry and tidy.

Notes:1The tile adhesive should be applied evenly, not too thick or too thin.

2.The pasting of tiles should be carried out in accordance with the brick seam line, and the brick seam line should be kept straight and vertical. 3.

Pay attention to safety in the cutting of ceramic tiles to avoid hand injuries during cutting. 4.After the tile adhesive is dry, the ground should be cleaned in time to avoid the tile adhesive remaining on the ground.

The methods and techniques of sticking floor tiles are as follows:

1.Preparation: First of all, you must prepare the tools and materials you need, such as tiles, tile adhesive, tile fiber finger cutting machine, level, plumb line, rubber hammer, racket, etc.

2.Clean the floor: Clean the floor to make sure it is flat, dry, and free of oil and debris.

3.Layout: According to the size of the floor and the size of the tiles, determine how the tiles are laid out, which can be measured and marked using plumb lines and levels.

4.Cutting tiles: Use a tile cutter to cut the tiles to the desired size and shape as needed.

5.Gluing: Use tile adhesive to apply the ground evenly, and the thickness is generally 3-5 mm.

6.Tiling: Stick the tiles to the ground according to the predetermined layout, and gently tap the tiles with a rubber mace to make them fit tightly with the ground.

7.Brick joint treatment: Leave a brick joint between the tiles, generally 2-3 mm, and use a beat to fill the gap between the tiles.

8.Waiting for drying: Waiting for the tile adhesive to dry, it generally takes about 24 hours.

9.Brick joint treatment: After the tile adhesive is dry, use tile grout to fill the brick joint to make it more beautiful.

It should be noted that when pasting and destroying the floor tiles, it is necessary to pay attention to the flatness and levelness of the tiles to avoid the misalignment or unevenness of the tiles. At the same time, it is necessary to pay attention to the size of the brick joints between the tiles and the filling method to ensure that the gaps between the tiles are uniform and beautiful.