The electric kettle accidentally fell into the water when it was connected to the water, and the bot

Hold your hands tightly and shake hard to shake out the water from the bottom. Then put some toilet paper at the bottom, put it in a cool and ventilated place, air dry naturally, and check that there is no watermark at the bottom after a while, you can use it, as long as there is no water in it, there will be no unsafe electricity when you use it.

If the electric kettle accidentally gets into the water, it can't be used immediately, it may be short-circuited, you need to let the water flow out diagonally, then gently shake it a few times, and then dry it with a rag, and leave it for a certain time before you can use it.

Try to dry the kettle, and don't connect the electricity immediately, this is a very dangerous action, and accidents will occur if you don't do it well. It's best not to use it now, wait until it's completely dry and try it again, and after trying it, you can use it, then there is no problem. If you can't use it, you have to fix it.

When water enters the bottom of the electric kettle, open the base of the electric kettle with a Phillips screwdriver, place the electric kettle in a ventilated place to dry, and use a hair dryer to dry the water inside the electric kettle; Fill the kettle again and you can use it again.

Blot dry with toilet paper or air dry with a hair dryer before reusing.

Pour out the stagnant water and dry it thoroughly, I really want to help you look forward to it

Drying is fine, it takes longer to dry or you have the ability to take the electric kettle apart and clean it up.

Just use a hair dryer to blow dry.

Generally speaking, it doesn't matter. Dry and let it dry.

It's better to change one if you can change one, this thing doesn't cost much.

It is very dangerous for water to enter the bottom, in case the circuit is short-circuited during the next boiling of water, and an electric man incident occurs.

The electrical appliances are as fierce as a tiger, so let's get a new one.

Loosen the bottom, shake off the water, and air dry for a day before using.

It's okay, drain the water first, and then prevent it for a day.

1. Because the electric kettle works at a high temperature, after a long period of use, the rubber ring will age and lose its elasticity, resulting in the leakage of water in the kettle. When the fastening bolts of the power cord wire are loose, the bolts should be tightened in time to compress the rubber ring to prevent leakage; When the sealing rubber ring loses its elasticity due to aging, it is necessary to replace it with a new high-temperature sealing rubber ring in time to ensure safe use. Carefully check for pot water leakage around the bakelite socket before powering it on after each water filling.

2. If the stainless steel kettle is leaking, the following methods can be taken: if it is a small eye, use a flat-head screw to pass through the eye, put a piece of rubber (preferably silicone) in the pot, drill an eye in the middle of the rubber sheet, put it on the screw, and then screw it and tighten it. If the rubber is not easy to find, use raw material tape to wrap a few times around the screw rod from the inside, add a flat smooth pad, or screw the screw.

Second, the electric kettle leakage repair - leakage repair method.

1. Remove the sealing ring and wash it.

2. Put 20ml of white vinegar and 250ml of water in a pot, put the sealing ring in the boiling white vinegar water and boil for 10 minutes.

3. Take it out and wash it with cold water, and when you put it on, it is obviously tight, and there is no further leakage.

Therefore, if the electric kettle leaks, it is not just to wipe the bottom of the electric kettle, but the leakage repair of the electric kettle of different materials may also be different, so everyone should repair it according to their own kettle material.

The bottom of the electric kettle is leaking, it is recommended not to use it again before repairing, the leakage problem needs to be repaired by professionals, and it can be sent back to the store for free repair during the warranty period.

1. If the water is not very serious, you can first use a hair dryer to aim at the contact port of the base, and dry the water flowing in, if you can, you can continue to use the electric kettle to boil water normally, if the situation is too serious, you need to repair, you can go to the store where you bought it to find a professional to repair, or buy a new electric kettle base to replace.

2. It is worth mentioning that when using the electric kettle, follow a certain method to avoid adding too much water when boiling water, or put it in an easy-to-touch place, so that it can effectively prevent water from entering the base, and the life of use will be extended a lot.

It is best not to use the kettle if it is flooded, in order to prevent electricity leakage. But if it's just water on the pot holder, then it can still be used, just wipe it dry.

Reason for water ingress in the kettle chassis:

Precautions: If the electric kettle fails, you should ask professionals to repair it in time, and do not disassemble it without permission to avoid the expansion of the fault or the occurrence of electric shock.

Dry, it's perfectly usable, but be sure to dry it.

1. The base of the electric kettle cannot be used immediately when water enters, so it is necessary to cut off the power supply in time, and then check the internal situation to avoid the risk of electric shock. First of all, we can disassemble it to see if it is a wiring problem, not serious with a hair dryer to dry, serious to the maintenance point to repair, after normal use.

2. After the water is in, we must first disassemble the electric kettle to see if the wiring inside is burned, if not, it means that the water is not serious, generally use a hair dryer to dry the water inside, if the hair dryer is blown or can not be used, it is necessary to check whether the thermostat has a short circuit, or the leakage device is working.

3. If there is a problem in the above situation, you can solve it in a targeted manner, if not, you need to find a professional maintenance point for repair, and if you feel troublesome, you can also directly replace it with a new electric kettle, which is basically not expensive, so that the safety is more secure.

What should I do if the electric kettle is drained? Every time you pour water, it leaks out along the spout?

What should I do if the electric kettle is slippery? Every time you pour water, it leaks out along the spout? Hello dear, <>

This is caused by the design defect of the water bottle outlet, and there are two options to solve it: 1. Fold the outer edge of the water spout to make the water outlet guide smoothly; 2, if you do not disturb the auspicious copper riveter experience, you can fill less water each time, after heating and boiling due to less water, the angle change when pouring water will not leak 2, 1, every time the electric kettle pours water, it will leak water along the account, that is, the spout of the electric kettle is too low, at this time you only need to use a vice to gently lift the spout of the electric kettle up a little bit and then use the pouring water, it will not have the depth of the spout to flow downward, do not need to move slowly to let go too much, as long as slightly to the top, Just warp it up a little bit on the line 2, every time you pour water will leak out along the mouth of the pot, that is when you pour water, the heart is too anxious, that is, it is poured too fast, you can not forget the work in your hands, carry too high, your too high, the water in this pot comes out too fast, he can't help it flow out of the concave place under the pot, you slow down, you try to see that the insurance will not leak out again, I hope to help you!

Allow to dry in the sun before use.

Or just change it.

If there is a leakage, it is recommended not to use it, in case of danger, it is not worth it.

The electric kettle accidentally fell into the water when it was connected to the water, and the bottom should be clear and should be in the water, what should I do?

Dried in use.

What should I do if the switch of the electric kettle accidentally gets the water.

Unplug the electric kettle first, blow it with a hair dryer, and leave it for a while before you can use it.

Can you continue to boil water if the base of the electric kettle is filled with water?

It's best not to continue boiling, my electric kettle is also flooded but I don't care, it won't work in a few days.

If the electric kettle accidentally falls into the water, can it still be used if it is wiped dry? (Pictured at the bottom.) 10 points.

The sun is basking and the hair dryer is blowing, all of which must be passed for a few days, for safety.

How to deal with water entering the handle of the electric kettle.

If you don't need it urgently, put it outside in a sunny and ventilated place, and it should be fine if you put it for a day or two. If you're in a hurry, just turn on the kettle and dry it inside, or dry it with a hair dryer.

What should I do if the bottom of the kettle is soaked in water.

Water enters the bottom of the electric kettle, open the base of the electric kettle with a Phillips screwdriver, place the electric kettle in a ventilated place to dry, and use a hair dryer to dry the water inside the electric kettle; Fill the kettle again and you can use it again. The working principle of the electric kettle is to use the water vapor generated when the water boils to deform the bimetal sheet of the steam temperature sensing element, and use the deformation to pass through the bar.

What to do if the water enters the fast electric kettle 5 points.

Allow to dry in the sun before use.

Or just change it.

If you order a leak and noisy electricity, it is recommended not to use it, in case of danger, it is not worth it.

What should I do if the kettle chassis gets water?

Pour the water clean and dry it in the sun!

Water enters the base of the electric kettle.

Generally, the regular seat can pass the water test, and the water does not affect the normal use, if you are worried about the danger, you can use a hair dryer to dry it.

Hello, Duan Xuqin is happy to answer for you that the leakage at the bottom of the electric kettle may be caused by the following reasons:1The bottom seal of the kettle is aged or damaged.

2.There are cracks or frays in the joints at the bottom of the kettle. 3.

There was a problem with the heating tube at the bottom of the kettle, causing the water to be too hot, which caused the seal to deform or crack. In view of the above problems, the following measures can be taken:1

Replace the seal: If the seal is leaking due to aging or damage, it can be removed and replaced with a new seal. Pay attention to choose the same model and specification of the sealing ring as the original, and make sure that it is installed correctly.

2.Replace the heating tube: If there is a problem with the heating tube that causes water leakage, you need to replace it with a new one.

This process requires disassembling the electric kettle and undergoing a detailed inspection, and it is advisable to seek professional help. 3.Replace the electric kettle before the whole deflation:

If none of the above methods solve the problem, then you may need to replace the entire electric kettle. When buying a new electric kettle, choose products with a good brand reputation and reliable quality, and pay attention to the use and maintenance methods. It should be noted that when carrying out any repair or replacement operation, be sure to disconnect the power supply first and wait for the kettle to cool down before operating to avoid safety issues such as electric shock and burns.