Beautiful. Evaporative cooling fan, can Midea evaporative cooling fan be used without adding water

1. Check whether there is no water sponge, if there is no water sponge, it is recommended to repair it;

2. Check whether the indicator light is turned on, if it still doesn't respond after opening, it is broken and needs to be taken for maintenance;

3. Check whether you need to add water, pour clean water before use, observe the water level through the water standard, control the amount of water added, unplug the power plug before adding water to prevent damage to the electrical components, and the water level to be irrigated can rise to close to the "highest" position, not too full.

Cooling fans originated in Japan in the 70s when they were only filtering pollen floating in the air, and were introduced to China in the 90s. The basic function of a cooling fan is to absorb heat from the air through water, so that the air temperature drops to achieve a cooling effect.

It's said that it's evaporation, of course, it turns water into gas and then blows it over, is there water droplets to wet the bed? Or buy a bargain, maybe there are water droplets!

It can be used, but there is no cold wind, it is a natural wind.

The cooling fan uses only 1 kilowatt-hour of electricity for 10 hours, while the air conditioner uses 12 kilowatt-hours of electricity.

Air conditioners can adjust the temperature and are suitable for indoor and other closed places, but they will get "air conditioning disease" if they blow for a long time;

The cold fan can not adjust the temperature, can only cool down, suitable for outdoor or open places, in closed places will have a feeling of stuffiness, because the humidity is too high, in open places will not be used, dry areas can be used as humidifiers, and environmental protection, health.

1. Instructions for use of Midea evaporative cooling fan.

How to use an evaporative cooling fan:

Step 1: After purchasing the evaporative cooling fan, turn on the power supply first to observe whether the cooling fan is normal and whether the hinge can also swing from side to side normally.

Step 2: The evaporative cooling fan is filled with water in the sink at the bottom, if everything is normal when the power is turned on, it is recommended to install water under the leaf pendulum, and then twist the switch to test the blowing. If you find it, it means that everything is normal, if not, it needs to be repaired to check whether there is no water sponge.

Step 3: The most important thing of the evaporative cooling fan is the two ice crystals below, and the refrigeration effect is also from the two ice crystals, these two ice crystals need to be cooled for 12 hours, let them enter the water tank, let the temperature of the water decrease, and then feel the strong sense of cold and wetness.

2. Precautions for use.

1: Placed horizontally. The air conditioner fan should be placed horizontally, pay attention to not tilt when using, and check whether the socket power supply is consistent with the parameters on the fan nameplate before use.

2: Add water often. The new machine or the air conditioner fan after a long time of shutdown must be filled with clean water before use, the water level can be observed through the water mark, the amount of water added should be controlled, the power plug should be unplugged before adding water to prevent damage to the electrical components, the water level to be irrigated can rise to close to the "highest" position, do not overfill; After filling the water, close the door, when used for refrigeration, pay attention to observe the situation of the water mark, when the water level drops to close to the "lowest" position, that is, the water should be supplemented, otherwise the refrigeration effect will be lost.

3: Frozen ice crystals. The general air conditioning fan is equipped with two ice crystals, every night, put one of them in the refrigerator at home for a period of time, and take it out the next day and put it in the water tank, the effect is better.

4: Humidify properly. If you want to use refrigeration and humidification to supply air, you must first fill the water tank with clean water, and after about 1-3 minutes of start-up, the air outlet temperature will be reduced by the ambient temperature to achieve the best effect.

When possible, add low-temperature cold water or ice water to achieve better cooling effect. If you add the right amount of spices to the water, it will blow out a burst of fragrant and cool breeze, which will make people feel relaxed and comfortable in the hot summer. Gently press the refrigeration and humidification, the indicator light is on, start the humidification function, if the humidification function is canceled and then press this button, the indicator light will be off, and the humidification function will stop.

5: Swing air supply. When you need to swing the air supply, you only need to press the "wind direction" selection key once to make the "swing wind" indicator light on, that is, the air supply will automatically supply air left and right immediately, and the air supply angle is 120 degrees, if you don't need to swing the air supply, press the wind direction selection key again to make the "directional wind" indicator light on, then stop swinging directional air supply.

At the same time, you can also adjust the position of the upper and lower air supply, such as adjusting the direction of the long air guide by hand, so that the air supply direction can be adjusted all down or up, according to your needs to adjust to the most ideal position.

You can use it, don't turn on the cold air! If you turn it on, you have to add water, or the small water pump inside will burn out!

Hello, will it burn without adding water?

Hello dear. A: The Lord will be happy to answer for you. 1. The wet curtain part is not wet during refrigeration.

Solution: It may be that the water distributor of the air conditioner is blocked, and it can be dredged and cleaned; Or there is no installation level, and the pad must be level. 2. The wet curtain is not wet during refrigeration (the hand control display is normal).

Solution: Check whether the water supply pipe of the water sock cloth and distributor is blocked, whether the water inlet of the water pump is blocked, and check whether the water pump is working normally. 3. The refrigeration icon flashes on the hand control.

Solution: This information indicates that the water level of the chassis in the machine is not enough, check whether the water inlet pipe valve is closed, the water inlet valve is blocked, or whether the water is stopped. If the water level of the chassis is normal, but it still shows a water shortage fault, it is a water level probe fault.

4. Water leakage. Solution: a. Water inlet pipe leakage:

The metal pipe is damaged or has no seal. Replacement is possible. b. Water leaks out from the overflow port of the drain valve

At this time, the water level is high, and the inlet valve float needs to be lowered. c. Leakage of side panels: For foreign objects left on the wet curtain, you can remove them, I hope the respondent can help you, I wish you a happy life and good health.

Some cold fans don't have heating pipes, so they don't have a heating function, you can see if there is a heating or heating knob on the lower panel!

Midea evaporative cooling fan AC120-G does not work.

Midea evaporative cooling fan AC120-G does not workHello dear, 1. The pressure protection switch is faulty. 2. Too much refrigerant causes protective shutdown. 3. The environmental temperature is too high, resulting in system protection.

The ambient temperature is too high, the sun is shining without shade, and the outdoor unit is poorly ventilated, which will cause the compressor to overheat in summer, resulting in the air conditioner not rotating. 4. Pay attention to whether the outdoor unit has working sound (including outdoor unit fan and compressor). If the outdoor unit fan is running, the control circuit is basically normal.

At this time, you should observe whether the compressor is started, if the compressor is not started, you should check whether the power supply is normal. 5. If there is no problem with the above checks, then it is necessary to check whether the capacitor is damaged and whether the overload protector is short-circuited. 6. Sensor failure.

Use a multimeter to measure the resistance value of the outdoor unit coil unit sensor, if the sensor resistance value deviates from the normal value or there is an open circuit or short circuit fault, the sensor needs to be replaced. 7. AC contactor failure. Power on the AC contactor, measure the outlet end of the AC contactor with a multimeter to see if there is a voltage of 380V, if not, it means that the AC contactor is damaged internally, and a new AC contactor needs to be replaced.