What s the matter with the mixer ash tank not being ashed, is there a problem with the computer?

When the bulk cement truck hits cement into the cement tank, the ash on the top of the cement tank often occurs, which has a great impact on the environment and workers, in order to prescribe the right medicine, it is necessary for us to understand why the cement tank will be ash, and how to solve the ash phenomenon.

According to the experience of Great Wall Construction Machinery for many years, there are two reasons for ash on the roof of the cement silo, firstly, it is usually due to the fact that the filter element of the dust collector used is not cleaned frequently, and the filter element has been blocked and cannot be removed normally; Secondly, it is caused by the damage of the level gauge, the cement in the cement tank is full, and the level gauge cannot be properly warned.

Once we know what causes the ash, we can prescribe the right medicine and solve the ash phenomenon in a targeted manner. Clause.

1. Clean or replace the filter element frequently, or directly use the active dust collector. Clause.

2. Always check whether the level gauge is normal. Clause.

3. Always check whether the solenoid valve of the cement silo has cement solidification.

How to troubleshoot the computer boot without display (check if there is a bulging capacitor). Step 1: First of all, check whether the external wiring of the computer is connected, and plug in each cable again to see if the fault is eliminated.

Step 2: If the fault persists, then open the main chassis to check whether there is any excess metal in the chassis, or a short circuit caused by the deformation of the motherboard, and smell whether there is a burning paste in the chassis, whether there are burned chips on the motherboard, and whether the capacitors around the CPU are damaged. Step 3:

If not, clean the motherboard from dust and check if the computer is OK. Step 4: If the fault persists, unplug the reset cable on the motherboard and connect it with other switches and indicator lights, and then use the change cone short-circuit switch to see if it can turn on.

Step 5: If it can't be turned on, then use the minimum system method, unplug the data cable of the hard disk, floppy drive, and optical drive, and then check whether the computer can be turned on, if the computer monitor shows a boot screen.

The mixer should be set in a flat position, and the front and rear axles should be padded with square wood, so that the tires are raised and overhead, so as to avoid walking when driving. 2. The mixer should implement two-level leakage protection, and after the power supply is turned on before going to work, it must be carefully inspected, and it can be used only after the empty car test transfer is qualified. During the trial operation, the speed of the mixing drum should be checked whether it is appropriate, under normal circumstances, the empty speed is slightly faster than the heavy car (after loading) 2 3 turns, if the difference is more, the ratio of the moving wheel and the transmission wheel should be adjusted.

3. The rotation direction of the mixing drum should be in line with the direction indicated by the arrow, if it does not match the truth, the motor wiring should be corrected. 4. Check whether the transmission clutch and brake are flexible and reliable, whether the wire rope is damaged, whether the track pulley is good, and whether there are obstacles around and the lubrication of various parts. 5. After starting the machine, always pay attention to whether the operation of each part of the mixer is normal.

When the machine is stopped, always check whether the blades of the mixer are bent and whether the screws have fallen off or loosened. 6. When the concrete is stirred.

Is there no substance left in the mixer ash can?

It is not a mechanical fault that the ash tank of the mixer is not ashed, this is a problem of the ash tank, and it is necessary to check whether there is ash in the tank to be determined.

The computer case should be cleaned frequently to ensure the normal operation of the computer. Here's why:

1. Clean up the dust on the motherboard to avoid poor contact with the inserted cards and boards. Poor contact of the board and card will directly cause the computer to crash or not work.

2. Clean the fans, including the CPU fan and the graphics card fan, to ensure the normal operation of the fan to ensure the CPU heat dissipation and graphics card heat dissipation. Once the CPU temperature is too high, the BIOS will start a self-protection program and shut down automatically, or even the computer will freeze or not function properly.

How to clean up the dust in the computer case: use a brush to remove it.

Yes! Too much dust on the computer causes heat dissipation problems, and the computer slows down! It will be a little clumpy after clearing, but it depends on whether you are slow down because of too much dust.

If the computer is used for too long, the indoor dust will increase, concentrated in the computer, and its damage to the computer is "dust is very harmful to the computer, too much dust may block the CPU fan, make the fan stop, cause the CPU to overheat and burn the consequences, but also affect the contact between the boards, and may also cause corrosion of the circuit board." So regularly clean the computer with dust, oil the floor fan, etc.!

A short circuit in the return of moisture, then a decrease in performance, and finally a fire extinguisher.

Cleaning the ash will make the temperature in your computer drop a little, in this way, the motherboard, hard disk and other hardware running environment is much better, of course, in all aspects will be faster, and develop the habit of cleaning the dust inside the computer frequently, will make the life of the computer much longer.

Laptop or desktop?

It is recommended to clean the notebook once every 1 year and send it to a professional to help!

Desktops don't matter!

Too much dust can have the following three effects.

1. Too much dust will produce static electricity to damage the circuit board and electronic components, so that its stability and service life are reduced.

2. If the CPU temperature is too high, it will cause problems such as frequent automatic restarts, crashes, and blue screens.

3. It is easy to accumulate dust on the blades of the power supply fan. The accumulation of dust on the power transistors and heat sink will affect the heat dissipation, and the dust accumulation on the fan blades will increase the load on the fan, reduce the fan speed, and will also affect the heat dissipation effect. When the room temperature is high, if the power supply cannot dissipate heat in time, the power transistor will be burned.

Therefore, dust removal and maintenance of the power supply is very necessary.

If the host is full of dust, this will affect the heat dissipation of the CPU and the heat dissipation of the motherboard, if the computer is seriously heated for a long time, it is easy to crash and blue screen, it is recommended to have time to clean the dust in the host with a small brush, so as to prolong the life of the host.

There is more dust in the power supply and radiator, which will affect the heat dissipation, and the noise will also increase, and the computer will run slowly, which may cause the computer to automatically restart, which is actually a kind of damage to the computer.

When there is a lot of gray and the weather is tidal, it is easy to cause short circuits. In addition, too much ash will seriously affect the heat dissipation.

The fan is hot, and the memory module is not in good contact. The CPU fan will automatically shut down if the fan is not hot.

To put it bluntly, the natural enemy of electronic components is dust.

Depending on the dust accumulation, it may cause poor contact between memory modules and graphics cards, and may also cause excessive heat accumulation inside the chassis, or even cause short circuits in some components.

My computer used to have a lot of problems due to excessive dust, such as the power supply burning, the poor memory contact, the radiator and the fan blockage, etc., and then I didn't cover the case cover and often cleaned the dust inside the case.

Hello landlord.

The dust removal system of the asphalt mixing plant does not absorb ash, which may be due to the blockage of the cloth bag in the dust collector. First, check whether the injection system of the bag filter is working well.

Then open the hatch cover of the bar, and bring out a cloth bag to see how the cloth bag is doing. If it is all blocked, you can only choose to replace the cloth bag.

Secondly, check the ventilation ducts of the factory. If there is a blockage.

There's no way around this.

After using it every day.

Just rinse it first.

When you say tank ash, you mean commercial concrete.

I can't say which one is better, but under normal circumstances, the quality of commercial concrete, after all, the ratio is controlled by mechanical and electronic equipment.

The proportion of concrete mixed by small mixers is estimated by the experience of the workers.

In addition, if a small drum mixer is used, the mixing quality is not guaranteed. The mixers used in the commercial mixing station are all compulsory, stirring.

This is simple, these things are energized, you directly cut off the power supply, don't you stop it, if your switch is broken, you can replace it with a new switch, what is the specific reason is not clear, but you can stop it by directly powering off! You can give it a try!