What does it mean to have a rubber stamp transfer to leave a blank space washboard and so on etc....

Transfer printing is to transfer the pattern to the eraser (so that you can engrave it) Transfer printing does not have to use nail polish remover or Rokushin flower water, originally used sulfuric acid paper to draw, and later "studied" the lazy method ......of using nail polish remover, etcHowever, nail polish remover and toilet water are really not very good for erasers, and they will cause some damage to erasers. The shelf life will be short, and it is said that the eraser will turn pink or feel delicate!

Blank space is the rubber stamp except for the rest of the pattern, get rid of the washboard is a way to leave blank, look beautiful, very neat a kind of blank space (if it is crooked, then ......）

This is the washboard.

If you cut the edge or something, you cut off the edge, for example, before the edge.

This is after trimming.

Generally, the washboard will be selected in the picture, and the outside will be cut

You can also choose to leave a flat blank ......If you cut it flat, it looks neat.

However, the inside can also be left blank, but it is more difficult to ......Generally, a flat white ...... is not used insideIt's a bit verbose, I'm sorry to hope

Transfer printing is to print the pattern on the sulfuric acid paper onto the rubber plate, so that it can be engraved.

Blank refers to the places where a seal will not stick to the ink after it is ready. These are the places that need to be carved out, and if it's a large piece, then it's a large piece of white space. You understand, right?

The washboard is a way to deal with white space, and after it is done, those white spaces are edged and edged, and they look like washboards.

Engo to Douban, the small station of the rubber seal or the post bar have tutorials.

Rubber stamp transfer printing is the use of some chemicals similar to nail polish remover, toilet water, cooling oil and other chemicals to glue the patterns or words printed on the paper to the eraser to form something like a pencil print on sulfuric acid paper printing (printing should be done with a laser!). The transfer of the blot is not very easy to wash off, but I am still in favor of tracing.

The blank space is to engrave off the unwanted pieces in the picture that have been printed on the rubber stamp, and cut it flat, which is more beautiful.

A washboard, like a blank space, is a sunken area that resembles a washboard by scooping out unwanted parts.

It's best for beginners to carve a washboard, and wait until you carve a fried chicken stick.

If you understand it, please find the answer on the rubber stamp bar.

The speech is a little verbose, I hope I can.

This kind of question doesn't need to be written here to ask a reward, you can ask it in the kindergarten in the rubber stamp bar.

<> "How to engrave a washboard with a rubber stamp."

1. Prepare a rectangular rubber brick, and then use a ruler and a pencil to draw stripes on it, all the way from the top to the bottom, so that the general shape of the washboard will come out.

2. Then use a carving knife to carve according to the lines of the stripes, it is best to remove the excess eraser while carving the jujube width, and dig out the stripe part of the cherry blossom in the middle little by little.

3. When carving, pay attention to the two lines above, one below, in a triangular shape, so that it will look more vivid, and the washboard rubber stamp will be completed after all the carvings.

To use rubber stamp transfer water, you need to print out the picture we need, then drop the transfer water on the paper to soak it, then print the patterned side on the rubber stamp, and then cover a plastic bag and scratch the paper with coins and bus cards.

Before we engrave the rubber stamp, we can use transfer water to print the pattern we need on the rubber stamp. If you want to use water transfer to print a pattern, first we need to print the pattern you like**.

Then open the purchased transfer water and drip it on the paper, and when the paper is soaked, we can stick the patterned side on the rubber stamp, and then cover it with a plastic bag and scratch the paper with coins and bus cards.

When we scratch the patterned paper, we must be careful not to use too much force, if we accidentally break the paper, we will have to start over. If we can't buy transfer water, we can also use nail polish remover and toilet water instead.

Eraser transfer water is a liquid substance that allows us to print patterns on washawa cherry paper onto rubber stamps. All we have to do is drop it onto the printed pattern, then stick it on the eraser and the leaky surface and cover it with a plastic bag and scratch the pattern on the paper repeatedly with a coin.

Rubber stamp transfer water is a liquid substance, which is an auxiliary tool that we need to use when we engrave rubber stamps. We can use it to print our favorite patterns from the paper to the rubber stamps.

Using transfer water to print a rubber stamp pattern is very simple and time-saving, we only need to drop it on the printed pattern, then attach the pattern to the rubber stamp and cover it with a plastic bag, and finally scratch the pattern on the paper repeatedly with something like a coin.

If we don't have transfer water, we can just use nail polish remover instead, but it is important to note that you should not use too much force when using this method to avoid damaging the paper. Moreover, this method is more suitable for laser-printed patterns.

Rubber stamp transfer water allows us to engrave the desired pattern on the rubber stamp, use it to transfer the rubber stamp as long as the required pattern is printed out, Fuqing and then drop the transfer water on the pattern to soak it, and then cover the pattern on the rubber stamp and cover the plastic bag, and then scrape it repeatedly with a hard object.

Rubber stamp transfer water can help us to carve out the ** printed on the rubber stamp, the use of transfer water is not often simple before the lack of branches, we only need to print out what we need.

Then put the transfer water on the printed ** and soak it, and then stick the side with the pattern on the paper on the rubber stamp, then remove a plastic bag and cover it and use something harder to scrape the paper repeatedly.

When we use this method to transfer rubber stamps, we must pay attention not to use too much force, otherwise the paper will be broken and the pattern we print will be flawed, and at the same time, we must fix the paper well, so as not to have a double image of the printed pattern.