What is epoxy mortar flat flooring?

【Introduction to epoxy flat coating flooring】

Epoxy flat-coated flooring is a two-component epoxy resin system, which is cured to form a thin film with a bright appearance, strong and tough, impermeable decorative surface, and easy to clean. Strong adhesion, good adhesion to the substrate; Can carry medium loads. The cost is economical, the viscosity is low, it is easy to construct, seamless dustproof, oil-resistant, easy to clean, and simple and convenient to repair and maintain.

Wear-resistant, compression-resistant, impact-resistant, waterproof and moisture-proof.

Epoxy Flat Coating Floor Features】 Epoxy Flat Coating Floor is a two-component epoxy resin system, which forms a thin film after curing, with a bright appearance, strong and tough, impermeable decorative surface, and easy to clean. Strong adhesion, good adhesion to the substrate; Can carry medium loads. The cost is economical, the viscosity is low, it is easy to construct, seamless dustproof, oil-resistant, easy to clean, and simple and convenient to repair and maintain.

Wear-resistant, compression-resistant, impact-resistant, waterproof and moisture-proof.

Epoxy flat coating floor construction steps] 1 base surface treatment: the debris on the original ground (such as: cement blocks, paint, etc.) must be completely treated; The smoother foundation should be sanded to increase the bonding strength of the original ground and EPOXY.

Check with a 2m ruler, smooth the high area with a grinder, and suck the dust with a small industrial vacuum cleaner. The moisture content of the ground surface layer should be less than 8%, and the non-conforming parts should be treated with gas grill drying and other methods until drying. 2.

Roller brush epoxy primer: mix the epoxy resin and the curing agent in proportion, and evenly coat the prepared epoxy resin primer on a clean, dry and rough ground with a flat knife or roller, and wait for it to cure naturally. Curing time is 8 hours (weather dependent.)

Check the primer coating, if there is a phenomenon that is completely absorbed by the foundation ground, it must be re-coated3Batch scraping epoxy primer mortar: After mixing and stirring the primer material in proportion, put No. 6 siliceous quartz sand into the primer material in a certain proportion and stir it evenly, pave it on the ground, and then spread it on the primer with a flat scraper to make it smooth and bond with the primer as a whole, and wait for it to be completely cured.

4.Grinding the mortar layer: use various grinders to coarsely grind the mortar layer, grind away the scraper marks and skipping marks of the mortar layer, and use an industrial vacuum cleaner or broom to remove the dust to prepare for the next process.

5.Batch scraping putty: use epoxy resin to mix the appropriate putty powder, it is advisable not to dry or thin, and use a flat scraper to evenly scrape the putty batch on the middle coating mortar layer to obtain a smooth and delicate coating to prepare for the coating on it.

6.Putty layer in sanding: Use various grinders to finely grind, polish and coat, and dust with an industrial vacuum cleaner or broom to obtain a clean surface layer.

7.Roller brush epoxy topcoat: use two epoxy topcoats (one scraping and one roller coating) to make the ground dustproof and waterproof, wear-resistant and corrosion-resistant, and easy to clean. After completion, the overall floor is bright and clean, and the color is uniform.

1. No bubbles, no hollow drums. 8. Curing: Sufficient curing time is of great help to improve the early strength of the floor, and indirectly affects the service life of the floor in the future.

Epoxy mortar flooring is one of the epoxy flooring series. Epoxy mortar flat coating floor has good acid and water resistance, oil resistance, acid and alkali resistance. It is generally used in silk screen printing factories, paper factories, warehouses, parking lots, garment factories, printing factories, toy factories, textile factories, beverage factories and other workplaces or light production areas.

Epoxy resin flooring has the characteristics of acid and alkali resistance, wear resistance, pressure resistance, impact resistance, mildew resistance, waterproof, dustproof, anti-slip, anti-static and electromagnetic waves, etc., and the color is rich and bright, and it is easy to clean. Epoxy resin flooring is a one-time coating process, no matter how large the area, there are no joints, and it is also a dust-free material with excellent properties such as strong adhesion, abrasion resistance, and hardness.

Epoxy mortar flat coating floor is suitable for electronics, medicine, food, chemical and other types of plants; car repair workshop; hypermarkets; Warehouse; Underground parking, etc. It has the characteristics of dustproof, moisture-proof and excellent wear-resistant; Strong adhesion, good flexibility, impact resistance, good hardness, high load; It can be used as non-slip floor, matte or high-gloss floor; Acid and alkali resistance, good mildew resistance; The color is optional, beautiful and bright; Easy to clean, fast construction and easy maintenance; 3-4 square meters per kilogram of lacquer paint. Since its introduction in China, epoxy resin flooring has been widely used in all walks of life, and has played a significant role in the production of enterprises with high-quality performance.

With the development trend of the times, the improvement of living standards, everyone's demand for chemicals, settlement situation is getting higher and higher, the previous dirt floor, concrete floor, diamond ground can not meet our needs, this time epoxy mortar floor should be born from time to time, this kind of epoxy resin coating mixed with fine quartz sand in proportion to prepare epoxy mortar floor, in the construction process of industrial production ground, epoxy ground, used to improve the compressive strength, seismic grade, wear resistance and other characteristics of the floor, Epoxy mortar flooring can further increase the service life and service life of the ground. What is the practice of epoxy mortar flooring? What are the characteristics of epoxy mortar flooring?

We've got you covered.

1. First of all, from the perspective of the characteristics of architectural coatings, epoxy mortar flooring has the functions of general epoxy flooring in addition to good anti-fouling, anti-wear and age, pressure resistance, impact resistance, and rust resistance of chemical organic solvents. It also has the practical effect of leveling, seamless, and smoothing the convex and concave ground.

2. Secondly, from the perspective of floor construction technology, when carrying out the solution of plain land, it is necessary to do a good job in grinding and polishing, repairing and dust reduction according to the situation of plain land. The topcoat of this kind of epoxy floor architectural coating is made of a topcoat with strong water permeability and adhesion to carry out the rolling paint to improve the surface adhesion. During the decoration construction, the paint needs to be rolled twice, and the floor after completion is generally bright and clean, the color is consistent, and there is no hollow wall.

Epoxy mortar floor features.

1. Ground solution: according to the ground conditions, do a good job of grinding and polishing, repairing, decontamination and ash removal;

2. Epoxy topcoat: choose a roller paint with super permeability and adhesion to improve surface adhesion

3. Epoxy cement mortar: add an appropriate amount of quartz sand with epoxy components, and apply sizing with a trowel to reach the required number of layers

4. Epoxy putty powder: add an appropriate amount of interior wall putty powder to the epoxy components, and apply one to two evenly sizing with a trowel to improve the flatness of the ground

5. Epoxy varnish: roll one or two with epoxy paint

6. Epoxy paint: use epoxy topcoat to make the ground bright and wear-resistant

7. The floor is delivered to make the use of Naxiang: 10-24 after painting, and 72 can be pressed.

The above is to provide you with epoxy mortar floor characteristics and epoxy mortar floor practice, water-soluble epoxy floor paint can be configured in various colors according to customer regulations;The thickness of the coating can be adjusted, which can be made into a thick film or a thin coating;It can be built into a non-toxic type to meet the health requirements. I hope that this information I have gathered about epoxy mortar flooring can help you.

Epoxy flooring is a kind of high-strength and beautiful flooring, so it is necessary to pay more attention to the construction method when painting the paint. So how exactly should you do it?Let's take a look.

Construction method: 1. Clean the ground before construction to ensure that the ground is clean.

2. Stir the epoxy resin and the curing agent according to a certain proportion, stir evenly, and apply it with a scraper or roller. During the application process, it must be soaked to strengthen adhesion.

3. Wait for the primer to dry and solidify before applying the epoxy middle coating. Apply the medium coating, continue to stir the epoxy resin and hardener in a certain proportion, and add a certain proportion of quartz. Use a trowel to evenly open the material according to the designed thickness to increase strength and impact resistance; Make the ground stronger and more compressive.

4. After the middle coating is dried and solidified, the sagging and particulate matter on the surface of the floor are polished and smoothed by grinding.

5. Apply the epoxy putty layer, stir the epoxy resin and quartz powder evenly according to a certain proportion on the clean ground, and then use a batch knife to scrape evenly on the ground after the core cherry, so that the medium coating and the ground are more closely combined, and then adjust the flatness of the entire ground.

6. Depending on the actual number of construction times, the entire ground is required to be flat and solid, without holes and without any imprints.

<> epoxy mortar floor has the advantages of high strength, wear resistance, beautiful and durable, no joints, solid texture, good chemical resistance, anti-corrosion, dustproof, convenient maintenance, and low maintenance costs. Is there a suitable requirement for the construction of the base surface in the construction process of epoxy mortar floor? The following is an introduction to the main content of epoxy mortar floor foundation construction brought by Zhongda Consulting for reference.

Epoxy mortar floor base surface requirements.

1. The cement base surface is firm, strong and does not shell, and the mortar shelling phenomenon should be eliminated, and the concrete layer and the mortar screed layer are best poured together. If the concrete layer is poured first, the thickness of the mortar layer is required to be no less than 40mm, and the requirements for the fork lane are thicker. The slope should meet the design requirements, and the allowable deviation value is 2% of the slope and not more than 30mm.

2. The surface is required to be sand-free, the hardness is matched with the high spike, and there is no cement pulverization. The newly poured cement mortar layer should be fully maintained. The cement base surface is flat, without unevenness, honeycomb surface, cement bumps, other coatings, latex paints, bubble gum and other residues.

Epoxy mortar floor base treatment.

1. In order to achieve good results in the construction of floor coatings, for the ground that has not yet been leveled, cement leveling should be constructed before construction for leveling treatment. When the civil construction party is leveled, the ground is smoothed with professional ground machinery when the cement is initially set. The surface of epoxy-coated flooring that has been treated with a base layer will be smoother, brighter, and the service life will be increased.

2. After the cement layer is dried (about 28d), the ground is polished as a whole with a grinding machine to make its surface smooth and the cement capillaries are all open.

3. For the base layer with oil stains (edible oil, engine oil), spray the surface with a surface treatment machine on the surface of the ground wet with water, and scrub it repeatedly until there is no oil stain.

4. For the base layer with too much alkalinity (pH>8), it should be neutralized with dilute hydrochloric acid or dilute acetic acid first, and then rinsed with water.

5. For the wet ground, through water absorption, pei to dry the travel, the sun, lamps, hot air blower blowing, so that the moisture content can meet the construction requirements.

Epoxy mortar flooring is one of the epoxy flooring series.

Epoxy flooring can be roughly divided into these layers.

Epoxy primer. Epoxy primal coated mortar.

Epoxy putty. Epoxy finish.

Epoxy flooring series.

a. Epoxy flat coating floor (ordinary workshop dust-proof, low environmental requirements).

b. Epoxy self-leveling floor (dust-free workshop, industrial production area with high requirements for plant purification).

c. Epoxy anti-static floor (manufacturing workshop of the electronics industry with requirements for anti-static electricity).

d. Epoxy mortar wear-resistant floor (the factory has heavy-duty operation of workshops, warehouses, passages, underground parking lots and other areas).

e. Anti-corrosion epoxy floor (electroplating plant and other places with a certain pH degree) f. Epoxy resin anti-slip floor (underground parking lot, etc.).

Fujian Sanhe Machinery floor grinding machine.

Epoxy floor paint is a floor paint produced using a mixture of epoxy resin and hardener.

Epoxy resin floor paint has the characteristics of strong acid and alkali resistance, wear resistance, pressure resistance, impact resistance, mildew resistance, waterproof, dustproof, anti-slip, anti-static, electromagnetic wave and so on, with bright and diverse colors and easy cleaning. It adopts a one-time coating process, no matter how large the area, there is no connecting joint, and it is also a dust-free material, with strong adhesion, abrasion resistance, strong hardness and other characteristics.

Epoxy resin floor paint is widely used in electronics factories, machinery manufacturing plants, hardware factories, pharmaceutical factories, automobile factories, hospitals, aviation, aerospace bases, laboratories, offices, supermarkets, paper mills, chemical plants, plastic processing plants, textile factories, tobacco factories, candy factories, wineries, beverage factories, meat processing plants, parking lots and other surface coatings. At present, it has been accepted and used by many domestic manufacturers.

Precautions: Avoid construction under low temperature and high humidity conditions; After the two-component material is mixed, it should be applied in a short time; After the coating is completed, it should be fully passed before it can be put into use; According to the flatness condition of the substrate and the requirements of use, the coating thickness is determined. The worse the flatness of the ground, the thicker the coating system is used, the greater the coating load, the thicker the coating should be, if the coating is too thin, it is easy to be damaged during use, such as the ground on the first floor also needs to do a good job of waterproof treatment.