What is the easiest mistake to make when installing windows and doors? Is there a remedy?

What is the easiest mistake to make when installing windows and doors? Is there a remedy? Door and window installation is the most basic decoration, but also the most important link, seemingly simple work, but if the installation of doors and windows is not standardized, it is easy to cause problems.

In the process of home decoration, the installation of doors and windows belongs to a more delicate work, a slight deviation will affect the overall use effect, and for the average family, the service life of doors and windows is relatively long, and decoration needs to be extra careful to ensure its service life.

<> the main reason for this problem is that the sliding door and window frame groove is not equipped with drainage holes, or the drainage holes are not properly positioned, resulting in the inability to drain the water in the tank when it rains. In order to avoid this problem, a rectangular drainage hole of 6mm and 50mm should be opened in the lower frame groove of the sliding door and window according to the need, and the drainage channel should be reserved. Doors and windows are deformed, damaged, plastic doors and windows are made of more brittle materials, hollow and hollow steel bars set in multi-chamber chambers are not welded, and their overall stiffness is poor.

As careful as we are, there are always small problems that keep popping up, some of which we don't even notice. Today I will talk to you about some mistakes and preventive measures that often occur in the process of installing doors and windows. After the problem is found, it will be dealt with according to the actual situation.

If the problem is minor, local correction can be made by heating and baking; If the problem is severe, remove the windows and doors and reinstall them. The verticality deviation of the front of the outer frame of doors and windows is large, especially for wooden doors and windows, the mortise and tenon are not dense, and the joints are easy to warp and deform, which affects the beauty and practicality in the later stage.

If the doors and windows are shaky, not vertical or uneven, the connection fixing points should be removed for correction, and then the iron feet on the frame and the embedded parts on both sides and under the frame should be welded firmly. If there is a water seepage problem, cement mortar should be used to fill the gap between the door, window and the wall, and sprinkle water for more than 7 days. The installation of doors and windows should be carried out in strict accordance with the construction specifications, the purchase of qualified materials, in accordance with the correct construction requirements, the owner also needs to accept the materials in a timely manner.

To avoid this problem, it is necessary to purchase steel doors and windows produced by regular manufacturers, and check whether the thickness of the anti-rust coating is uniform, and there are no obvious quality defects such as stacking and missing coating. The lower frame device of the window frame should be carried, and after the window sill is wiped on the cement, the slope top and the window frame should be kept at a height of more than 8 mm, and the arc angle should be concave, so that the window drainage capacity will be smoother.

Dimensions are prone to errors, and holes are not well handled during installation, which can be remedied with a dilator.

When installing doors and windows, the most common mistake is that the actual size of the opening is inconsistent with the actual size of the door and window.

Poor sound insulation, no ventilation, latex flowing everywhere, not easy to clean, wrong direction, poor lighting; Before doing it, you must have a reasonable plan, dismantle, wait until it is completely sealed, ventilate more, and use a small amount of latex many times each time.

The choice of the type of door and window. When installing doors and windows, you should think about it in advance, what kind of effect you want to achieve by installing doors and windows, for example, if you want to have good heat insulation, sound insulation, and ventilation effects, then the first choice should be to choose sliding windows, and then casement windows. The size of the opening is not suitable.

If the size of the opening is too large, the gap between the door frame or window frame and the wall will be too large after installation, and it will be difficult to seal it in the later stage. It is prone to water leakage, air leakage, and poor sound insulation. If we find that the size of the hole is too small, and we forcibly install the doors and windows in the hole, it will cause the doors and windows to be deformed.

The location of the door and window installation is often with railings, so when installing doors and windows, the original railings need to be removed. The railings are installed by the developer when they are built, and they often go deep into the wall, and after the railing is removed, there will be several grooves on the wall. Whether it is a door or a window, you must pay attention to the accuracy of the scale.

The scale here naturally refers to the door frame and doorway, the window frame and window of the window, the door and window are too large to be installed, needless to say, the key is small, as the door is good to say, as long as it is not too strong, the surrounding filling of some things can still be installed.

<> windows did not have drainage holes, and rainwater accumulated and seeped into the house. The window structure is too messy, very random, and the risk of rain leakage is greatly enhanced! A good glue has a direction and order.

Air leakage at the junction between the window frame and the glass. Under normal circumstances, the glass and the frame are connected by a sealing strip, but if the strip has been aged, or broken, or falling off, it will cause air leakage and no sound insulation, which means that the window configuration itself uses inferior products and the quality is not up to standard.

Gluing is also very important, and the styrofoam should be played sufficiently without leaving gaps. The sealant should be neatly made, and it can't be wiped out in one go, otherwise it will be ugly. Install all the window frames first, then all the windows, and if you want to install guardrails, be sure to do it after the windows are installed.

After the installation position of the window frame is positioned, it is fixed, and the fireproof styrofoam is used to fill the joint. Finally, after the exterior wall decoration or interior decoration is completed, the glass installation is carried out.

The most common mistake to make when installing doors and windows is the question of opening inside or out, which will affect the position of the cabinet or items.

The windows do not have drainage holes, which is the most common mistake to make when installing doors and windows. If there is no drainage, there is a high chance that it will leak. Therefore, this matter must be taken seriously.

In the process of installation, the gap is not fixed, so that the weather is windy or rainy when it will enter the house, as far as possible to avoid such a situation, the installation must let the worker master wipe the seam well, at that time my home was not installed when decorating, and then it was very troublesome again.

The most common mistake is to make the wrong size, choose a very bad material, and finally not be strong and not strong in sealing.

1. There is a large gap between the door and window sash and the frame.

When decorating, it may be the installation master, the gap is too large, or the installation is not perpendicular to the ground, the door and window sash can be removed and repaired to match the frame and then reinstalled, if the door and window frame is not vertical, the gasket in the frame plate should be straightened. Knocking on the side panel of the door sleeve with your hand has a hollow drum sound, indicating that the bottom layer is not lined with a large core board, and the panel should be removed and the large core board should be added.

2. The side of the window opening is not vertical.

The main reason is that there is no cushion wood piece to straighten, and the cushion should be reworked and flattened, and the cushion board should be installed after measuring with a long ruler. The surface has color difference, damage, rot spots, cracks, etc., which must be solved by replacing the veneer.

3. The door opening and closing is not smooth.

The main reason may be that there is a problem with the installation of the lock, the deadbolt of the door is not installed correctly, and the size of the corresponding lock is not suitable. The deadbolt plate should be removed, the tongue groove should be repaired with a chisel, and the position of the deadbolt of the door frame should be adjusted before installing the deadbolt plate.

4. Sliding doors and windows are laborious and cautious.

The main reason is that the center line of the upper and lower tracks or rail grooves is not in the same plumb plane, and the tracks can be unloaded first, and the upper and lower tracks and the center of the rail grooves can be aligned with a vertical ruler.

Door and window installation is a very delicate and important work in our home decoration, and a slight deviation in the operation process will affect the overall use effect. And for us, the correct installation of doors and windows has a great impact on the service life of doors and windows.

Today, let's talk about what problems are particularly prone to occur in the installation of doors and windows? And how can we prevent it?

What are the problems in the installation of doors and windows?

1. The verticality deviation of the outer frame of the door and window is large, which leads to the fact that the tenon of the wooden door and window is not compact, and the joint is easy to warp and deform, which greatly affects the practicability of the later stage.

2. It is easy to deviate when installing hardware hinges, the size of the hinge silver slotting is not the same, the installation of hardware screws is not accurate, and the edges of doors and windows are not smooth.

3. After the installation is over, the vertical seams and joints of the doors and windows are large, and the doors and windows are not closed tightly in daily use, and the rainwater will flow into the room when the wind leaks in winter or even in rainy days.

How can we prevent these problems?

1. Before installation, strictly install the construction drawings, prepare the measurements and materials, and then operate in accordance with the correct construction requirements.

2. The measurement of the position of the hardware hinge must be fine and accurate, the size of the hinge and the hinge groove should correspond, and the depth should be consistent.

3. The door and window switch is flexible and smooth, and it is necessary to ensure that the edge of the door and window is not warped, and the installation of screws is very important, remember not to warp.

4. When installing the door frame, you need to lift the frame upward, wipe the cement dirt of the window sill and install it.

5. After the installation, it is necessary to do a good job of anti-corrosion of doors and windows, which can reduce the damage of doors and windows and prolong their life.

Door and window decoration belongs to a large decoration project, which involves a lot of knowledge, if the construction personnel are not careful, it will be the door and window decoration distorted, and the future will be deformed to produce a series of problems, how to avoid these problems, and how to supervise the construction personnel to do a good job in the decoration of doors and windows, which requires a certain amount of common sense, and then I will share the experience of door and window decoration for you.

First, it is best to replace the doors and windows before removing the windows Because the process of removing the windows will damage the indoor and outdoor walls, it is best to replace the doors and windows before the next step of decoration. It is recommended that you should choose high-quality brand doors and windows when decorating doors and windows, because the quality of door and window profiles will determine the grade, sealing and anti-aging of the entire door and window.

Second, it is recommended to go to the regular building materials market, especially some inferior plastic doors and windows, the quality of the lining steel is poor, and even there is no lining steel, and other accessories are also very poor.

Third, why do doors and windows turn yellow The appearance color of some plastic doors and windows is too white or gray, indicating that the stable components in their materials are not enough, and they are easy to age and turn yellow over time.

Fourth, check whether the hardware is flexible and smooth, there should be aluminum slide rail at the lower part of the sliding window frame to facilitate its replacement, and there should be a fixed piece in the middle of the sealing strip of the sash, which is the key to the sealing of the sliding window.

Fifth, the door and window installation between the window frame and the wall should be filled with styrofoam, and the inside and outside of the window frame must be sealed with silica copper glue or sealant to prevent water seepage. Remember, after installation, the user should remove the protective film, which can extend the service life of the doors and windows.

Do you understand the five steps of door and window decoration, door and window decoration looks artistic, but in fact, the knowledge inside is quite deep, and a little attention will bring trouble to open the window or open the door in the future, so the owner supervises well, the door and window belong to the external image of a home, and must be maintained!

You can get it for free

Common problems of door and window decoration, we will discuss from the door and window gaps, hardware, door switches, construction, glass, etc., and the following we will introduce you to some problems and solutions that are easy to occur during the construction of wooden doors and windows.

Large gap between the door and window sash and the frame: the main reason is that the planing is not accurate during installation and the door and window frame is not perpendicular to the ground, the door and window sash can be removed and repaired to match the frame and then reinstalled, if the door and window frame is not vertical, the gasket in the frame plate should be straightened.

Poor installation quality of hardware: the reason is that the hinge of the swing door is not straight, resulting in uneven door and window sash and frame cover. You can screw one screw on each hinge first, then adjust the flatness of the door and window sash and frame, and then tighten all the screws after adjusting and repairing.

If the hinge screws are short, the screws are nailed in and tilted at one time, the doors and windows will be rough and burning, and the appropriate screws should be replaced during repair. When the screw is attached, it must be straight, and the screw should be driven into the full length of 1 3 first. Then screw in the remaining 2 3, it is strictly forbidden to nail in at one time or tilt screwed in.

The door opening and closing is not smooth: the main reason is that the lock is installed with a problem, the deadbolt plate should be removed, the tongue groove should be repaired with a chisel, and the deadtongue position of the door frame should be adjusted before installing the deadbolt plate.

Sliding doors and windows when sliding: the main reason is that the center line of the upper and lower tracks or rail grooves is not in the same plumb surface, and the center line of the upper and lower tracks or rail grooves should be aligned by adjusting the track position.

Wooden door and window cover construction: Wooden door and window cover construction is highly technical, and the common quality problems are as follows:

The side of the window opening is not vertical: the main reason is that there is no skids to straighten, and the pads should be reworked and flattened, and then the cushion board should be installed after measuring with a long ruler.

The surface has color difference, damage, rot spots, cracks, etc., which must be solved by replacing the veneer. The wood used for the door and window cover should be the wood and color coordination of the door and window sash, the color difference between the veneer and the wood line can not be large, and the wood species should be the same.

Knock on the side panel of the door sleeve with your hand and there is a hollow drum sound, indicating that the bottom layer is not lined with a large core board, and the rock void should remove the panel and add a large core board.

I believe that as long as you master the diagnostic skills and tricks, you can calmly judge the quality of door and window decoration and related problems, and correct and solve them in time.

<><What are the problems in the installation of doors and windows?

In home decoration, the installation of doors and windows seems to be very simple, but if you don't pay attention, it will still cause a lot of problems. According to the editor-in-chief of the blog, there are usually three major problems in the installation of doors and windows.

First, the color difference of doors and windows is obvious.

2. Leakage of doors and windows.

3. The overall stiffness of the door and window frame is poor.

First, the color difference of doors and windows is obvious.

a) Phenomenon. Adjacent doors, windows, or window frames are not the same color as the sash.

b) Causes. The material is not the same factory product, or the same batch of products, or products of different material grades.

c) Measures. 1. The purchase of profiles should use the same products of the manufacturer, and prepare sufficient materials at one time.

2. Pay attention to the matching before blanking.

2. Leakage of doors and windows.

a) Phenomenon. 1. Leakage at the junction between the door and window frame and the surrounding wall.

2. The water in the chute under the sliding window is eliminated and seeps into the window.

b) Causes. 1. Cement mortar caulking of door and window frames and walls.

2. The glue injection between the door and window frame and the wall is not strict, and there are gaps.

3. The process of doors and windows is unqualified, and the combination between the window frame and the window sash is not strict.

4. The installation of the sash sealing strip is unqualified, and the water seeps into the window drowning glass cracks.

5. There is no drainage hole in the window frame.

c) Measures. 1. Door and window frames and walls shall not be caulked with cement mortar. It should be elastically connected and sealed with sealant, and there should be no gaps.

2. Before installation, check whether the doors and windows are qualified, whether the old and stupid fit between the window frame and the window sash is strict, and whether the installation of the window sash sealing strip is qualified.

3. There is a gap of more than 50 mm between the window frame and the hole, so that the window sill can be used as a flowing slope.

4. Drainage holes should be drilled for the lower frame of the outer frame and the root of the track.

3. The overall stiffness of the door and window frame is poor.

a) Phenomenon. Pushing, pulling, opening and closing doors and windows or encountering windy weather, door and window frames shaking.

b) Causes. 1. Improper selection of profiles, small cross-section, and insufficient strength. The prevention of aluminum alloy door and window materials does not meet the requirements. The quality of plastic steel doors and windows is unqualified.

2. The lining steel configuration of plastic steel doors and windows does not meet the standard, (the general steel lining is used, but the owner cannot see it because of the installation.) Many businesses use unqualified ones to install for the owners) the steel has thin walls and poor strength; The lining steel is inserted in sections, and the overall strengthening effect is not formed; The lining steel is not firmly connected with the plastic profile, etc.

3. The installation node is not specified in the specification.

4. There are no different fixing methods according to different walls.

c) Measures. 1. The specifications and quantity of door and window frame profiles meet the national standards. The wall thickness of the outer frame of the aluminum alloy profile shall not be less than mm. The thickness of the plastic steel window material shall not be less than mm.

2. Check the appearance of plastic profiles, and the qualified profiles should be blue-white or ivory-white, clean and smooth. Better quality should have a protective film.

3. Select the profile section according to the size of the door and window openings and the installation height, and the casement window is not less than 55 series, and the sliding window is not less than 75 series.

4. Install in strict accordance with the specifications to ensure firm and stable.