Ask about the relationship between the splitting strength of concrete core sample and the conversion

According to the provisions of Appendix C of the "Quality Inspection and Evaluation Standards for Highway Engineering" (JTG F80 1-2004), the measured splitting strength of concrete core samples should be converted into flexural tensile strength through the empirical statistical formula of their respective projects, and the average flexural tensile strength fcs and minimum value fmin must be qualified.

Usually a batch of data of trabecular flexural tensile strength fc and the corresponding splitting strength FSP with the same ratio, the same material and the same conditions should be established, and the corresponding coefficient of and sum should be obtained by referring to the formula fc= of the JTJ T Sliding Form Construction Technical Specification. Apply this formula to calculate the flexural tensile strength fc.

Concrete core sampling is mainly to check the quality of the concrete core of the cast-in-place pile, such as the cementation of the concrete core, strength, whether there are porosity, segregation or broken pile, etc. Diamond drilling is generally used for core sampling, and the diameter should be 76mm.

Generally, the empirical formula is determined by oneself through experimentation. But JTG

F30-2003 can be calculated according to the following formula:

Limestone, granite concrete: flexural tensile strength = power of splitting strength.

Basalt concrete: flexural tensile strength = power of splitting strength.

Gravel concrete: flexural tensile strength = splitting strength.

Summary. Hello, happy to answer your <>

The splitting tensile strength value of concrete is known, and the method of converting it into axial tensile strength value is as follows: the axial tensile strength ft of concrete can be converted according to the splitting tensile strength fts, and the conversion coefficient can be determined by the test. Generally, the side length of 150mm square is used as the standard specimen, and the conversion coefficient is used, if the 100mm 100mm 100mm non-standard specimen is used, the split tensile strength value obtained should be multiplied by the conversion factor.

Knowing the tensile strength value of concrete splitting, how to convert it into axial tensile strength value?

Hello, happy to answer your <>

The tensile strength value of concrete splitting is already known, and the method of converting the axial tensile strength value into the axial tensile strength value of the concrete shaft is as follows: the tensile strength ft of the concrete shaft can be converted according to the tensile strength fts of the splitting and stuffy Sakura, and the conversion coefficient can be determined by the test. Generally, the side length of 150mm square is used as the standard specimen, and the conversion coefficient is used, if the 100mm 100mm 100mm non-standard specimen is used, the split tensile strength value obtained should be multiplied by the conversion factor.

The tensile strength of concrete splitting is 10% of the compressive strength. The tensile strength of concrete excavated concrete refers to the axial tensile strength of concrete, that is, the maximum load of the concrete specimen when it breaks after tensile force divided by the stress value obtained by the product of the cross-section ruler, which is expressed in FTK and the unit is MPa. There are two main methods for testing the axial tensile strength of concrete, one is the direct test method, and the other is the splitting test.

The conversion factor is based on which standard.

It is the "Design Code for Highway Reinforced Concrete and Prestressed Concrete Bridges and Culverts", oh, pro-<>

Generally, the empirical formula is determined by oneself through experimentation. However, JTG F30-2003 can be calculated according to the following formula:

Limestone, granite concrete: flexural tensile strength = splitting strength to the power of basalt concrete: flexural tensile strength = splitting strength to the power.

Gravel concrete: flexural tensile strength = splitting strength.

What is the splitting force value of pavement concrete core? Flexural strength is an important indicator for structural design and quality control in road and airport engineering, and compressive strength is used as a reference strength index. The design flexural strength of cement concrete required by the road pavement of each traffic grade is extra heavy and heavy traffic volume

5MPa (medium traffic.)0MPa (light traffic). The standard specimen for the flexural strength test of cement concrete is 150mm 150mm 550mm cube, which is measured by the right-angle prismatic trabecular according to the loading method of three-point point.

What is the splitting force value of pavement concrete core? Flexural strength is pro! Hello, I am glad to answer for you<> pro In general, the flexural strength of concrete is about 1 5 1 10 of its cubic compressive strength, which is a multiple of the tensile strength of splitting.

The flexural strength test uses 150mm, 150mm, 600mm (or 550mm) trabeculae as standard specimens. In general, the flexural strength of concrete is about 1 5 1 10 of the strength of its cube compressive pants, which is a multiple of the tensile strength of splitting. The flexural strength test uses 150mm, 150mm 600mm (or 550mm) trabecular as standard specimens.

The flexural strength of each type of concrete is different, and the use of concrete with different flexural strength is also different, and the life of a house built of concrete with stronger flexural strength will be longer. Extended material: I hope mine can help you <>

Do you have any other questions?