-
There are many reasons why the unicycle cannot be charged, such as poor contact, faulty data cable, faulty charger, etc.
Solution to the problem of not charging the battery:
1. Poor contact.
Check whether the charging interface of the unicycle is in good contact with the data cable, if the contact is not good, it will not be charged;
Check whether there is any foreign object in the unicycle interface, resulting in poor contact with the charging cable;
2. Replace the power cord or data cable.
Try to replace the cable or charger, it may be a fault of the cable or charger, replace them separately to identify what the problem is.
3. Turn off and start again.
If you have tried all the above methods and still don't work, it is recommended to turn off the unicycle and start it again. Sometimes the wheelbarrow itself is chaotic, which may also lead to the failure to charge.
Fourth, the reason for temperature.
The battery on the unicycle is particularly sensitive to temperature, and in some areas with low temperatures, such as minus degrees, it may not be able to be charged due to low temperatures. If the temperature is too low to charge, you can put the unicycle in a warm place and charge it when the temperature rises.
5. Hardware failure.
If the above reasons are ruled out, it may be a hardware problem. If there is a hardware problem, it is recommended to send it to a local repair point for inspection of the wheelbarrow.
-
My electric unicycle hasn't been charged for about a month, why is it not charging at all now and the charger just shows a green light?
Hello, I am happy to answer for you: the battery of an electric unicycle that has not been charged for a month may have been over-discharged, resulting in a very low battery level, and the green light displayed by the charger at this time only means that the battery level is extremely low and cannot be charged normally. In this case, the following needs to be done:
1.Plug the e-unicycle into the charger to charge it and wait for a while (it may take hours or more) for the battery to charge to a certain extent. 2.
If the battery level does not increase after charging for a period of time, or the charger's display light still only shows a green light, the battery may have completely failed. The battery used in the electric unicycle needs to be replaced with a new one. 3.
When replacing the battery, you need to pay attention to the battery model and specifications used in the electric unicycle to ensure that the charger can charge and protect it normally.
-
Although most of the problems are the battery, it is not absolute, you can check whether the function of the motherboard is normal.
-
The wheelbarrow cannot be charged, and the battery cannot be discharged, which may be due to the broken battery or the wiring problem.
-
The new battery has already been charged when bought at the store, so it can't be charged much, and it will not affect the use and discharge time. Some old batteries have a reduced capacity and are full after a while, but the discharge time is shortened.
-
Find its instruction manual.
Let's take a look at what this should be.
And how to exclude.
If you can't solve it yourself, go to the after-sales service department.
-
Replace the battery, the lithium battery is obviously scrapped. The wheelbarrow is built into a lithium battery (can be easily removed from the battery compartment with a screwdriver), the lithium battery is not used for a long time, one or two months need to be replenished, once it is shelved for a long time, the power is exhausted, the voltage is zero for more than a month, the ternary lithium battery is very difficult to charge and recover (the voltage is zero for half a month, the probability of charging is less than eighty, and the capacity is seriously damaged, it may only be 60 percent), the lithium battery lacks power for a long time, which is to show the state you describe.
Remove the lithium battery to see how many strings the battery is combined (look at the battery label), get the voltage capacity, measure the length, width and height of the battery shape, search online to buy the same specification of lithium battery (the size is in line with the voltage, the capacity can be larger and smaller).
1. If you can't turn on the machine, the biggest possibility is that it can't be turned on due to insufficient power. Check to see if the plug is plugged in properly and confirm that the phone is charging. >>>More
Cables, charging heads, and tail plugs are all possible, but there is no way to rule out which one is the problem, you can only find someone who uses the same iPad as you to try to change things, and see if it is the first problem.
The power adapter converts the alternating current into direct current and adjusts the voltage to the specified voltage and then outputs it to the notebook charging module, the battery charging module will control the connection between the adapter and the battery according to the charging ratio set by the computer, if the battery power ratio is not reached, the battery will be charged, and a certain amount of power consumption will be generated in this process, so heat will be generated, which is a normal situation. If the overheating affects the use, it is recommended to go to the service center for testing.
vivo phone can't flash charge, you can solve it as follows: >>>More
Because the charging current does not meet the charging standard of the iPad.