The external flash in the studio doesn t flash, it s a hurry

Updated on number 2024-08-05
16 answers
  1. Anonymous users2024-02-15

    Among domestic brands, Godox flash is very powerful in terms of ** or product performance. Inquiry**: The main products are:

    Studio flashes, location flashes, power boxes, photographic lights, flash remotes, camera remotes, studio accessories, and other camera accessories are all CE and RoHS certified by the European Union. At present, Godox photographic equipment has become one of the enterprises in China's photographic equipment industry with rich product types, high technical content and fast R&D and update speed. Shenzhen Shenox Photographic Equipment Co., Ltd. began to produce photographic equipment products in 1993, and is a comprehensive photographic equipment enterprise integrating product development, design, manufacturing, sales and other all-round services.

    Through the continuous efforts of the Shenniu people, the Shenniu photographic equipment has been developed....

  2. Anonymous users2024-02-14

    It seems that there are two channels of triggering, one is through the internal flash to emit light, and the other is through the radio signal. Since light triggering is no problem, it is that electric triggering is not suitable.

    See if the channels at both ends of the sending and receiving ends are the same? If it doesn't work, it's damaged and needs to be repaired.

    There is also the need to plug in the remote control when plugging in the hot shoe, otherwise the contact will be poor.

  3. Anonymous users2024-02-13

    Look at the flash, the two channels are connected, the flash is connected, the flash is luminous, the flash, the line, the electrical signal is not the problem, the electric flash is suitable.

    Look at the channels at both ends of the sending and receiving ends, causing damage to repair.

    To hot shoe plug in the remote control must be stuck in place, otherwise the contact is good.

  4. Anonymous users2024-02-12

    Manually, test button pressed flash? If it doesn't flash, the light is broken, and if it does, check the photoswitch and photodiode. It really didn't work, so I changed the trigger to this lamp.

  5. Anonymous users2024-02-11

    First, make sure that the light of the photosensitive flash is turned on.

  6. Anonymous users2024-02-10

    If you use the trigger, it is possible that your camera does not flash or the flash is too weak to cause the flash to be triggered.

  7. Anonymous users2024-02-09

    After turning off the light-sensitive trigger of the fuselage, unplug the external signal trigger, if it does not flash, turn on the light-sensitive, if it does not flash, it proves that the signal trigger is bad.

  8. Anonymous users2024-02-08

    The other one didn't turn on the trigger? You can reinstall it again, I have occasional problems like this.

  9. Anonymous users2024-02-07

    If the camera flash does not flash, it should be faulty, and if the external flash does not flash, it should be due to the wrong channel between the light and the trigger, or the trigger is dead.

  10. Anonymous users2024-02-06

    It should be a studio flash with a built-in flash in the camera, right? If so, check the camera's built-in flash settings, if you can adjust the built-in flash to manual, you can use the studio's light-sensitive flash. ETTL can only use Canon lights, not other flashes.

  11. Anonymous users2024-02-05

    This is normal,After all, you are now relying on the camera's own flash to trigger the photographic light,This kind of flashing is to test the light sensitivity of the film and television lamp to trigger the flash,That is to say,When the light sensitivity button of the film and television lamp is turned on,The film and television light will produce a flash of light,If you want to synchronize,You need to buy a set of flasher,So as to ensure synchronous flash。

  12. Anonymous users2024-02-04

    Half of your camera shutter should be adjusted to less than or equal to 1 160 seconds, and then try again, if it doesn't work, buy a trigger, trigger cable can also be used.

  13. Anonymous users2024-02-03

    Because you don't have a flasher installed on your body, you can't synchronize.

  14. Anonymous users2024-02-02

    The flash of the camera itself is not synchronized with the studio flash, and in order to synchronize, an external flash or trigger must be used.

  15. Anonymous users2024-02-01

    If none of the above solves your problem, check to see if you haven't plugged in and connected to.

  16. Anonymous users2024-01-31

    Normal! This is formed by strong light entering the capillaries in the pupil, which is generally felt strongly in dark places, because the pupils at this time are relatively wide, so it is easy to shoot red eyes**. After answering, I hope it will be helpful to your question, if you are satisfied, please adopt o(o...Ha ha.

Related questions
11 answers2024-08-05

Friend, you should be using a Canon camera, and the model is not clear, because some models come with a set-top flash, and some do not, but I will try to help you as much as possible. >>>More

3 answers2024-08-05

1. BrightnessThe flash uses a capacitor to store high-voltage electricity, and the pulse trigger discharges the flash tube to complete the instantaneous flash, especially in dim places, and the flash helps to make the scene brighter. Brighter brightness. Relatively speaking, the brightness of the camera light is not as high as the flash, and the camera light is portable to operate, with RGB mode to create different color temperature environments to meet the shooting needs of different scenes. >>>More

26 answers2024-08-05

The curvature is set when the studio is built so that the studio can become more solid, because it is a little confused, and it can better bear the pressure on the upper part of the studio.

5 answers2024-08-05

Brother, I understand what you mean, it's good, I'll add a little bit to you; >>>More

30 answers2024-08-05

The steps to set up the flash for incoming calls are as follows: first open the settings on your iPhone, then find "General" in the settings, and click to enter. Then find "Accessibility" in General and click to enter. >>>More