What should I do if the seat belt is removed and cannot be pulled out, and the seat belt cannot be p

Hello, it is very normal for this situation, for the safety belt, it must be put right after disassembly, as long as there is a slight tilt will not be pulled out, it must be put right.

Hello, the stretching of the seat belt also has a position, if you pull deadly, it will not be pulled out, to eliminate the fault of the seat belt itself, you can install and fix the seat belt and then stretch it.

If the seat belt is pulled quickly, it is stuck, you try to drag it out slowly, and you can do it. If you can't drag it out slowly, then the card slot inside is damaged.

Hello, this may be caused by a stuck seat belt, you ask the repairman to check it, it really can't work, you can only replace the assembly.

After the seat belt is removed, it can't be pulled out, it is likely to be stuck, and it is recommended to go to a repair shop for repair.

My Wuling light door encountered the same situation, slowly feed back, there is a click, a sound to pull out to try, mine about four or five sounds, you can pull out a large section and then stuck, and then slowly feed inside, a sound on a pull to try, almost four or five after pulling out a large section, it can be installed.

Hello, this one may be a seatbelt stuck. It's best to go to a 4S shop or auto repair shop to disassemble it.

In this case, it should be caused by the seat belt getting stuck inside, and it is recommended to check it.

Hello, is it stuck, take it apart to see, or directly replace it with a new seat belt, the seat belt also has a service life.

The solution to the seat belt that cannot be pulled out is as follows:

1. Adjust the height of the high-profile adjuster, so that the seat belt can obtain excess retraction, so as to restore its shrinkage performance.

2. Smooth the seat belt, slowly stretch back and forth at the entrance and exit of the seat belt, and slowly pull it out after the seat belt is retracted and smooth.

3. If the above two methods are not feasible, it is likely that there is a mechanical failure in the place where the seat belt is bridged with the interior of the car, and this situation needs to be disassembled and repaired in 4S.

Information about seat belts

1. Definition of seat belt: A seat belt is a vehicle safety device designed to protect vehicle occupants from harmful movement that may be caused by collision or sudden stop.

2. Relevant regulations: For those who do not wear seat belts on the co-pilot, the traffic police on duty can impose relevant fines and penalties on the passengers. According to the provisions of the Road Traffic Safety Law, the passenger of the co-pilot shall also wear a seat belt when the motor vehicle is moving.

3. The role of seat belts: to reduce the possibility of death or serious injury in a traffic collision by reducing the secondary impact force with the danger of internal impact, to ensure the maximum effectiveness of the airbag by making the occupants correctly positioned, and to prevent the occupants from being ejected from the vehicle or the vehicle from rolling over in a collision.

The driver's seat belt is stuck and the seat belt cannot be pulled out, which can be adjusted and solved, and the specific operation method is as follows

1. First of all, the seat belt adjustment button can be found in the position of the vehicle diagram, as shown in the following figure

2. After that, you can use your hand to press down on the button, so that you can adjust the height of the seat belt, as shown in the figure below

3. After that, press and hold the button with both hands and move down to lower the position of the seat belt, as shown in the figure below

4. In this way, you can adjust the position of the seat belt by pulling it down, as shown in the figure below

This is generally due to internal consumption and cannot be repaired, and can only be replaced. The role of seat belts in sedans: when the car encounters an unexpected situation and brakes urgently, it can bind the driver and passengers to the seat to avoid rushing forward, thereby protecting the driver and passengers from injuries caused by secondary collisions.

The role of the car seat belt is to make it in the event of a collision or use of the vehicle.

The seat belt can not be pulled out, it is generally stuck or a mechanical failure occurs, and if it is stuck, you can try to restore it appropriately, if it is a mechanical failure, please find a professional to repair it.

1. The seat belt is jammed.

Improper use will deform the seat belt, and it is easy to jam at the entrance and exit of the seat belt. This situation is relatively simple, generally the seat belt is smoothed and then slowly pulled out.

2. Mechanical failure occurs.

If the seat belt is not deformed, it will not be able to pull the hose, and a mechanical failure may occur at the bridge between the seat belt and the inside of the car body. In this case, it is necessary to go to the repair shop or 4S shop to disassemble for further inspection, and replace the parts if necessary.

About seat belts:

The car seat belt is a kind of protective equipment, which "ties" the occupants to the seats to avoid damage caused by the passengers in the car due to inertia hitting the front glass, seats and other objects or throwing out of the car when the car collides violently. The car safety early knowledge belt and the car airbag cooperate with each other, which is an important part of car safety. Now China's road traffic law clearly stipulates that drivers must wear seat belts when driving, otherwise corresponding penalties will be imposed.

The production of seat belts has made outstanding contributions both in the field of automobiles and in the field of road safety.

The seat belt does not pull out, usually because it is stuck or mechanically malfunctioning. If you get stuck, you can try to extend the recovery appropriately. If it is a mechanical failure, please find a professional to repair it.

1.The seat belt is stuck.

Improper use will deform the seat belt, and it is easy to get stuck in the entrance and exit of the safety belt. The situation is relatively simple. Generally, you can flatten the seat belt and then pull it out slowly.

2.There is a mechanical failure.

If the seat belt is not deformed, that is, it cannot be pulled out, the bridge between the seat belt and the body may cause a mechanical failure. In this case, it is necessary to disassemble in the repair shop or 4S shop for further inspection, and if necessary, replace the parts.

About seat belts:

The car seat belt is a kind of blind protection device, which ties the people in the car to the seat to prevent the passengers in the car from hitting the front glass, seats and other objects or throwing out of the car due to inertia when the car collides violently. Car seat belts and airbags work together and are an important part of car safety. At present, China's "Road Traffic Law" clearly stipulates that drivers must wear seat belts when driving, otherwise they will be punished accordingly.

The emergence of seat belts has made outstanding contributions both in the field of automobiles and in the field of road safety.

Millions of car purchase subsidies.