How to install the car seat cover, how to install the car seat cover?

Car cushion installation, the specific steps are as follows:

1. First of all, take out the seat cushion of the new car and check it, as shown in the figure below.

2. Next, put it into the cushion vest, as shown in the picture below.

3. Then, put on the saddle head cover, as shown in the figure below.

4. Next, take out the chuck as shown in the figure below.

5. Then, install the chuck on the sling of the seat cushion as shown in the figure below.

6. Next, after installing the chuck, insert the chuck into the gap as shown in the figure below.

7. Then, insert the chuck into the buffer pad and plug it as shown in the figure below.

8. Next, check the chuck after carding, as shown in the figure below.

9. Then, adjust the cushion apron as shown in the figure below.

10. Next, snap into the elastic band of the car seat cushion retainer, as shown in the figure below.

11. Then, put it into the headrest, as shown in the figure below.

12. Finally, the installation of the car seat cushion is completed, as shown in the figure below.

There is an advertisement on the first floor.

How to install a car seat cover, and how to remove a car seat cover:

The car seat is composed of a backrest and a seat, and the front seat and the rear seat are installed differently, so the car seat cover installation is divided into four parts: the front backrest, the front seat, the back backrest, and the rear seat.

1. Install the [front backrest cover]:

First take off the headrest of the front backrest (sometimes you need to press and hold the headrest activity bolt), then carefully cover the [front backrest cover] (pay attention to the left and right sides and the front and back), and then wear the front of the [front backrest cover] from the gap between the seat back and the seat to the back side, and finally glue the front and back of the [front backrest cover] with the hook and loop (it will be firmer if you stick it hard).

2. Install [front seat cover]:

First, lay the [front seat cover] on the seat surface, put the edge down after inserting the seat, pass the hook and loop on the [front seat cover] under the seat and pass through the black buckle, and then fold back and stick it with the hook and loop (it will be firmer if you stick it hard). Finally, the elastic bands on both sides of the edge and the two elastic bands on the seat surface can be tied together separately (pay attention to carefully tidy up the flat seat cover).

3. Install [back back cover]:

First take off the backrest headrest on both sides (sometimes you need to press and hold the headrest movable bolt), then carefully put the [backrest cover] carefully (pay attention to see the left and right sides and the front and back), and then wear the front of the backrest cover from the gap between the seat back and the seat to the backside, and finally tie the elastic bands around it together.

4. Install [rear seat cover]:

First of all, spread the [rear seat cover] on the seat surface, put the edge down after putting it into the seat, turn the seat over, and tie the elastic bands around it tightly together (pay attention to carefully arrange the flat seat cover).

1. First of all, take out the new car cushion and check it. 2. Put it into the cushion vest 3, put on the seat cushion head cover 4, take out the chuck 5, install the chuck on the suspender of the cushion 6, install the chuck into the gap 7, and then stuff the chuck into the cushion and jam it 7, check it after the chuck is clamped 8, and then adjust the cushion apron.

The method of installing the car seat cover is actually very simple. Now many car owners because of the installation of car seat cover is more difficult, so a long time do not change the car seat cover, the car seat cover installation method is very simple, the following author will introduce to you, I hope the owner will no longer worry about this, can easily change the seat cover.

1. Back backrest: first pull out the headrest, press the activity bolt of the backrest in different ways to pull out the headrest according to the different structures of the car. Then put the backrest cover well, and when putting it on, the upper and lower parts should be clearly distinguished, and it should be placed in the correct position; Stuff the rubber band at the bottom of the front of the back back cover to the back of the backrest, string the rubber band from the bottom to the back and tie it with the rubber band above, and tie the side rubber band and the side rubber band.

Then straighten the covered backrest, insert the headrest, and the back backrest is installed.

2. Rear seat: The general car of the rear seat pulls up a little hard, and the whole seat can be turned up directly, so the installation is quite simple. First, put the seat cover on the seat, adjust the position, and pull the rubber band at the front of the seat from under the seat to the back and tie the rubber band at the back.

Then tighten the rope at the rear end, and then arrange the seat cover flat, and the rear seat seat is installed.

To install the car saddle, the specific steps are as follows:

1. First of all, take out the seat cushion of the new car and check the bottom of the shirt, as shown in the figure below.

2. Next, put it into the cushion vest, as shown in the picture below.

3. Then, put on the saddle head cover, as shown in the figure below to excite.

4. Next, take out the chuck as shown in the figure below.

5. Then, install the chuck on the sling of the seat cushion as shown in the figure below.

6. Next, after installing the chuck, insert the chuck into the gap as shown in the figure below.

7. Then, insert the chuck into the buffer pad and plug it as shown in the figure below.

8. Next, check the chuck after carding, as shown in the figure below.

9. Then, adjust the cushion apron and socks as shown in the figure below.

10. Next, snap into the elastic band of the car seat cushion retainer, as shown in the figure below.

11. Then, put it into the headrest, as shown in the figure below.

12. Finally, the installation of the car seat cushion is completed, as shown in the figure below.