Home users are affected by ARP attacks, why is the home network also affected by ARP attacks? How to

You're being attacked by other users in the whole LAN network, like a cell that comes from a backbone signal that interconnects through a switch, so there's a situation like this.

It can also be caused by the ARP virus.

Update your antivirus software to the latest version, restart it and enter safe mode to check and kill all of them. You can also collect ARP killing tools on the Internet.

ARP virus!?It's not like yes, the landlord said that it was attacked, and my understanding is that the landlord's network was attacked by ARP. An ARP attack is a network action, not a problem with your computer.

An ARP attack is when a network is paralyzed due to a blockage of data packets, or a computer is running slowly. Because ARP attacks are a global problem with a long history, and ARP attacks are diverse, the solutions are different.

Solution. You go to the address above and take a look, there are many ways. You can choose one according to your situation. Bless you. Your IP address has been taken by hackers.

1ARP virus inside your machine. Packages are issued from the inside out. It was brought in by other Trojans.

2. Check to see if you have any software installed in your machine, similar to network tools, if so, uninstall it!!

Go to the next ARP kill on the Internet.

Next360ARP Firewall.

Get your feet wet!

Prompt: ARP attack does not necessarily mean that ARP virus has been hit, when someone in the network is using network management software such as P2P OVER, there will be the same prompt; It is estimated that someone may use network management software to do management! It's best to use the binding of the MAC address and IP of the network to solve the problem! Binding Method:

Enter cmd in [Start] -- Run] to enter the command prompt mode.

Second, use arp -d to clear the current arp cache, and then use arp -s gateway ip) xx-xx-xx-xx (gateway mac) to bind the source wisely. It's a good idea to make a bat program and set it to run automatically when you boot up.

Again, if you can get into the router, it's a good idea to make a table on the router that corresponds to the IP and MAC addresses of the computer.

If not, it is best to check which computer sent the ARP packet through the 360ARP inspection tool, disconnect its network cable, and check for viruses.

The problem of IP conflict should be that someone on the network has set the IP address of the computer to be the same as yours, and you had better set the IP to get it automatically. If it's already automatically fetched but still prompted, you can use ipconfig release to release the original IP and then use ipconfig renew to get the new IP.

Someone uses P2P terminator, or a webmaster enforcer or something like that.

Install an ARP firewall.

Just use 360 He has protection against ARP attacks.

1.ARP attacks are forged IP addresses and MAC addresses to achieve ARP spoofing, which can generate a large amount of ARP traffic in the network and block the network. This mechanism determines that it is an attack within a local area network, simply put, it is the same network that you are connected to.

It can generally be seen in online neighbors.

2.In your case, it's likely that someone is attacking the router to crack the password.

3.Resolution.

Method A: The most thorough is to turn off the wifi and use the wired o ( o haha, of course it is not very convenient to make;

Method B: Turn on the anti-attack function on the router (if your router supports it, it can be used with method C);

Method C: Bind your own computer and phone to Mac; (Look for the manual according to your router model).

Somebody has speed limiting software installed, and as soon as it turns on, your computer is attacked, and the problem is very simple. There are many ways to kill it.

There's a good chance that your other computers have viruses.

It's impossible for your own family to do bad to your own family!

Someone installed LAN restriction software.

For example, Jusheng network management, P2P terminator, etc., the software that limits the speed of others will be like this.

First, bind your IP to your Mac (static binding).

This must be a problem with the intranet, someone uses P2P terminator, Jusheng network management, these software are using the principle of ARP deception, of course, there will be a hint of ARP attack, this is already attacked on your computer, it is recommended that you use the immune network solution, not only can intercept the virus attack from the network card but also can intelligently control the speed, to ensure the security and stability of the network.

Installing an antiarp firewall with color shadow can basically solve the problem, the software is a paid software, such as pointing the home page to the cooperative mode can be used for free.