HP notebook reboots after reinstalling the system, and keeps staying in the HP logo interface, what

1.It is recommended that you can choose to enter safe mode by clicking the F8 button when you boot (or restart).

a.If it is normal in safe mode, the system and hardware are normal

Since the safe mode is a diagnostic mode and does not run the driver and software, if the safe mode can be entered, it is recommended that you uninstall the driver and software you installed before to test it;

b.If the problem persists in safe mode, then your problem may be due to a problem with the system installation and you cannot access the system.

It is recommended that you refer to the following methods to set up the optical drive boot and reinstall the system;

Put the installation disc into the optical drive and restart your computer.

When the "HP Compaq" logo appears on the screen, press the "F9" key continuously.

Select "cd ***."

romdrive" and press the Enter key to confirm.

Note: Due to the different models, the interface of the optical drive boot is slightly different, please select the one that represents the optical drive.

It is recommended that you provide a follow-up inquiry with the specific model and the version of the system you currently intend to install, so that I can give you specific suggestions on the installation system.

We hope you find the above reply helpful.

Reinstall the operating system, you can't install it yourself, it is recommended to spend 30 yuan to let the repairer help you install.

This situation may be due to the fact that the computer cannot detect a certain hardware during the self-test or is stuck in the detection of a certain hardware.

1. Keyboard and mouse, the boot self-test will detect the mouse and keyboard, if there is a problem, it will cause the card to the self-test interface, the solution is to pull out the keyboard mouse search imitation mask, check whether it passes the self-test, if the state passes the self-test, replace the Daqiao mouse and keyboard.

2. Hard disk and optical drive, the most likely is the hard disk and optical drive, the desktop needs to open the chassis, unplug the power cord of the hard disk optical drive to see if it passes the self-test, if it passes, further rule out the problem of hard disk or data cable.

3. If none of the above is true, then the most likely thing is that there is a problem with the motherboard BIOS and needs to be returned to the factory for repair.

When the computer is turned on, it has been stuck on this icon, and when the computer is turned on, it has been stuck on this icon, and when the computer is turned on, it has been stuck on this icon, and it should be that the mountain bucket is the computer card machine, and it may be that the only school has not been turned on for a long time, or if the frequency of use is relatively high, this kind of card will appear.

After selecting the language and version, start**, and put the image into the boot USB flash drive when you are done. 3.Boot and press the del button to enter the BIOS to set the judgment rock to be placed, press del to enter the main interface of the BIOS setup program, find "BOOT" in the upper menu, dig and select, back.

Summary. Hello, dear, the computer stays on the restart, which is generally caused by two reasons:

The first reason is a system boot error, which causes the system to fail to boot again. It is recommended to use a USB flash drive with PE, after entering the USB flash drive, select enter PE, and then start the repair through Windows, and directly repair the C disk to solve this problem.

The second reason is that the system loses files and cannot enter, and the system generally encounters this phenomenon, which can only be solved by reinstalling the system.

What should I do if my HP computer is stuck on the reboot screen?

Hello, dear, I am the Q&A Lord, I received your question, and I am sorting out the answer, please wait, I will reply to you within ten minutes.

Hello, dear, the computer stays on the reboot side, which is generally caused by two reasons: the first reason is the system boot error, which causes the system to fail to boot again. It is recommended to use a USB flash drive with PE, after entering the USB flash drive, select to enter PE, and then start the hole repair and excavation through Windows, and directly repair the C disk to solve this problem.

The second reason is that the system loses files and cannot enter, and the system is sensitive, and this phenomenon is generally encountered, and it can only be solved by reinstalling the system.

2. If you have not carried out special hardware operations, please press the F8 key when you turn on the computer to see if there is an option of "choose to use the latest correct configuration" or "safe mode". If you can see "Select to use the most recent correct configuration", please select it to see if it enters the system normally. If you can't access the system, try to enter "Safe Mode" to see if you can back up your important data.

3. If it is not easy to use, please press the power button and press the "F10" button again to test whether you can enter the BIOS? If you confirm that you cannot access the BIOS, it is likely that the hardware is faulty, and the specific cause can only be determined after actual testing.

The HP Care Pack Service Center is responsible for hardware testing, repair and replacement services, so in order not to delay your use, it is recommended that you contact your local HP Care Service Center to help you detect the specific cause of the failure and then deal with it. You can find the nearest HP Care Pack Service Center by following **:

You are welcome to feedback your operation results or questions through the follow-up function, so that we can continue to follow up and solve your problems, and I wish you all the best!

Unplug the hard disk and optical drive first, and then try to boot it, the card logo is the time point when the motherboard detects the external device. If it doesn't work, it's a problem with the motherboard. It has nothing to do with memory.

There is also a series of prompts that it should be a problem with the BIOS, and the computer cannot perform internal inspection.

Eighty percent of hard disks, try to change blocks.

If you have files and materials on the C disk and desktop, then don't install the system, if not, you can completely reinstall the system.

Summary. 1. This situation is caused by system damage, if there is a system recovery function, you can press F8 to repair the system when you turn on the machine, and follow the prompts to restore the system to factory settings.

2. If the system recovery is unusable, you need to install the system manually.

1. First of all, you need a ghost version of the system disk.

2. Press the F2 button to select Start from CD when you boot up.

3. Select Enter PE System in the Disc option.

4. After entering the system, use the one-click restore tool in the PE system to restore the system image in the disc to the C drive.

5. After the restoration ends, start the computer from the new, the system will automatically install the drivers and applications, and the computer will automatically restart and enter the system when everything is ready.

6. The installation is complete.

After the HP computer was factory restored, it has been stuck in the HP interface and cannot be operated.

1. This situation is caused by system damage, if there is a system recovery function, you can press F8 to select the repair system when you start the machine, and follow the prompts to restore the system to factory settings. 2. If the system recovery is unusable, you need to install the system manually. 1、First of all, you need a ghost version of the system disk 2、Press the F2 key to select Start from CD 3、Select enter the PE system in the CD option 4、After entering the system, use the one-click restore tool in the PE system to restore the system image in the disc to C disk 5、The restoration is over and start the computer from the new,The system seller will automatically install the driver and application,Everything is ready to be installedThe computer will automatically restart and enter the system。

6. The installation is complete.

Hello, pressing f8 can't operate <>

He doesn't work on any keystrokes.

After clicking on the power on, press F8 wildly