Breitling watches are foggy, where is the after sales center?

Recommendations for the use of mechanical watches:

1. Watches with manual winding movements should be wound at the same time every day as far as possible so that the watch has enough energy to operate in the next 24 hours.

2. The energy of the watch with automatic movement is ** in the movement of the wearer's arm, so there is no need to manually wind it under normal wearing, only when the wearer's exercise is not enough to replenish enough energy to the mainspring, it can be compensated by manual winding, and the crown rotation is controlled within 20 laps when winding.

3. For a self-winding watch that has not been worn for more than 40 hours, the crown should be turned 20 times to reactivate the movement when worn again.

4. In order to prevent moisture from penetrating into the case and maintain the waterproof performance of the watch, please make sure that the crown is locked at all times.

What to do if the watch gets water.

It is normal for the watch to get water, if the water is not serious, but there is a layer of fog in the watch glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it for about 30 minutes at a distance of 15 cm from a 40-watt light bulb to eliminate water vapor. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours.

Of course, there are also some daily repair methods for watches to get into the water:

1. Dry the granules with silica gel. If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

2. Bake with a light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

3. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe.

4. Send the watch shop to wipe the oil. None of the above three methods can remove water vapor, so you should immediately send it to a watch shop to wipe the oil to remove the moisture from the movement to avoid rust on the parts.

5. Bake with a light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

6. Dry with a hair dryer, the temperature should not be too high, the wind is mild, and you know that you can't see the moisture on the glass.

If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts. Remember not to disassemble the movement yourself, so as not to damage the movement, and then repair it will be more time-consuming, laborious and costly.

1. Anti-magnetic demagnetization.

The metal material of the watch is very easy to be magnetized and cause the watch to malfunction, so try to avoid placing the watch next to magnetic objects, such as mobile phones, computers, magnets, metal buckles of bags, car door handles, automatic mahjong machines, etc. Once the watch is magnetized, it will cause inaccurate time, it is recommended that you send the watch to a professional luxury repair and maintenance center for demagnetization as soon as possible.

2. Prevent collisions.

No matter how good the quality of the watch is, it is composed of a sophisticated movement, and a collision can easily cause mechanical damage and scratches on the appearance of the watch. It is recommended that when you wear a watch, you must try to avoid the watch being collided, and if the watch is damaged by the collision, it must be sent to a professional luxury maintenance center for professional repair and maintenance in time.

After 2-3 years of use, the waterproof rubber ring of the watch will deteriorate, which may lead to water ingress problems. It is recommended to conduct a waterproof performance test once a year and replace the waterproof gasket in time to avoid water ingress. Try not to use the watch often in hot and humid or extreme environments, so as not to cause water problems in the watch.

When using the watch in normal use, you should avoid strenuous exercise with the watch, so as not to damage the case or handle and affect the sealing of the watch. If the water is ingress, it is recommended to send it to a professional maintenance shop for treatment in time.

First, when the watch is in water and fog, the simplest way is to wear the watch on the wrist backwards, that is, let the watch mask reflect inwards and the bottom case of the watch face outward. After a few hours, you will notice that there is less and less moisture inside the watch.

Second, prepare a little paper towel or moisture-absorbing flannel, wrap the watch tightly, place it on a 40-watt light bulb about 5 cm, and bake it for about half an hour. Later, you will notice that the moisture in the movement gradually disappears.

Thirdly, it can also be used to remove fog vapor by basking in the sun. First turn the back cover of the watch open, then wrap the watch completely with a paper towel or moisture-absorbing flannel, and take it to the sun to bask in the sun for most of the sound, which can also remove the moisture in the movement. If the watch is severely flooded, it can be left for a longer time.

Fourth, after the watch enters the water, you can first open the back cover of the watch, remove the battery, and use the hair dryer to aim at the water meter at low temperature. After blowing until completely dry, put the back cover device back from the beginning. You can also check whether the sealing ring is aging and broken when you install it, and remember that the back cover must be fastened if it is in good condition.

There is fog in the watch, which means that there is moisture in the watch. In general, although the watch is hermetically sealed, there are very small pores in the joints of the case, especially in used watches.

When washing hands or washing clothes or on rainy days, water can enter through these pores, especially the hot steam in the kitchen, which is more likely to soak into the case. In addition, the temperature is high and the humidity is high in summer, so if the watch is suddenly cold, the air containing more moisture in the watch will condense into mist or water droplets, which will stick to the watch glass.

If water enters the watch, please send it to the repair center immediately for treatment, otherwise it will cause many metal parts inside the movement to oxidize and rust due to water vapor, causing greater damage.

You can take a large professional and regular watch repair shop and let the master help you take a look. You can get the Guangcheng watch store on the first floor of No. 325 Beijing Road, Yuexiu District, Guangzhou, and let the master help you inspect and repair.

Straps are consumables, especially leather straps, even the best alligator leather straps have a lifespan of about 2 years if they are worn regularly. Exposure to sunlight and contact with body sweat can cause a lot of damage to the strap. Humid air or water can easily cause the strap to dry out and deform, and it will have a foul smell.

Precautions for leather strap maintenance:

1. Long-term strong sunlight mapping will decolor the exterior color of the leather strap, and will also accelerate the aging of the leather strap cortex, and some chemical tests such as perfume will also change or decolor the color of the leather strap;

2. When wearing a leather strap and pulling too hard, it is easy to reveal cracks in the position where the leather strap is often fixed, (the greater the buckling rate of the leather strap, the easier it is to break), so it is best to be cautious and gentle when wearing a leather strap.

3. Like other leather items, the most taboo thing about leather straps is water, and if you soak them in water for a long time, the leather strap will immediately become hard and brittle, especially the sweat absorbed. Therefore, it is completely forbidden to wear a watch with a leather strap to swim (or do things that are in contact with water for a long time), and the long-term sweat penetration can also make the leather strap moldy and smelly.

4. To clean the leather strap, you can gently wipe the strap with a damp soft cloth, and then put it in a dark and ventilated place to dry. Every 1-2 months, wipe the strap with a leather strap protector and then wipe the surface with a maintenance agent to maintain the texture of the leather strap and improve its brightness.

5. Don't fold the strap in half, the strap has a greater degree of hardening in winter, and don't "fold back" to hurt the leather.

You can remove one or two sections, and if it's a belt, you need to make one or two more holes.

What material is the strap? What went wrong? Specific analysis of specific problems. If you have any questions about your watch, please call the main service platform 4008521212 the 12-scale watch

Hello, glad to answer for you!

Room 601, Block B, New World Office Building, No. 3-5 Chongwenmenwai Street, Dongcheng District, Beijing] [010-59504813].

Reasons for inaccurate time:

The watch's kinetic energy reserve is insufficient

The watch is affected by a magnetic field

The watch has been hit or struck by an outsider

The watch has not been maintained for a long time

The watch battery is low.

If the watch is faulty, you can call for consultation**!

The working principle of a Breitling mechanical watch is that the pendulum in the mechanical watch drives the human arm back and forth to rotate the winding wind, resulting in elastic deformation, and then it is set by the machine to control the amount of recovery from its elastic deformation, that is, the movement of the second hand. The interlocking of the gears forms the relative position of the hour, minute and second hands, and the time can be displayed.

There are many parts inside the watch, gears, springs, screws, and shafts.

If you feel an abnormal noise, or the watch has stopped, it is likely that the parts are loose or have fallen. Or debris, in which case you'll have to go to a repair center to have it checked. The hidden danger of debris in the watch is still very large, the light one is stuck in the gear to cause time error, and the heavy one causes damage to the parts, making the life of the watch shorter.

It is recommended that you go[Room 808, Block E1, Oriental Plaza Office Building, next to Wangfujing Street, Dongcheng District].Perform a series of tests.

It may be that the internal parts are loose after the fall, and this situation is sent to the repair center in time to avoid causing more damage to the internal parts. The sooner the better, the early stage may be repairs or screw fixing, because the movement is very complicated, and later it may be the part that is damaged. It is also possible that there is a problem with the internal parts of the movement, the wheel is the heart of the mechanical watch, the hairspring is the power source, the upper and lower shafts of the balance wheel have shockproof bearings, if it is a slight collision, it can absorb the deformation caused by the shock and automatically return, when the force is larger, the bearing displacement is larger and can not automatically return, causing the balance wheel to tilt and rub the frame, as long as the bearing is not bent to recover, once the bending is difficult to return to the original state, it will affect the accuracy of the time.

The hairspring will also adhere to the misalignment when it collides, and it will generally not be deformed and can be easily recovered. Other components or gears may also be misaligned and cause stalls, depending on the situation. You can go to the testing center to check what the reason is, and then determine the cost of repair.

Proper use and maintenance.

1. When wearing a watch, the sweat on the hands is corrosive to the case, the all-steel case is nickel-chromium alloy, the corrosion resistance is better, the semi-steel case is copper, long-term contact with sweat, easy to corrode, should often wipe off the sweat with a soft cloth or pad the plastic watch holder to prevent it from being eroded by sweat.

2. Do not open the back cover of the watch at will, so as not to enter the movement and affect the normal operation of the watch.

3. Do not put the watch in the wardrobe with mothballs to avoid the deterioration of the watch oil.

4. Do not put the watch on the radio or TV to avoid magnetization.

5. Watches that are not worn for a long time should be wound regularly once a month so that the parts will not be in a static state for a long time, so as to ensure the operation performance of the watch machine.

If there is an abnormal sound inside the watch, it may be that the internal parts are loose after falling, or it may be that there is a problem with the internal parts of the movement, in this case, it is recommended that you send it to the repair center in time to avoid causing more damage to the internal parts.

Shanghai Watch Service Center is located in Room 1003, 10th Floor, Hongyi International Plaza, No. 299 Nanjing East Road, Huangpu District, Shanghai.

Methods of degaussing.

First, it is a professional demagnetization of the watch shop.

Methods of degaussing.

2. If you are far away from the watch repair shop, you can also demagnetize yourself, the specific method is: find a piece of iron that is hollow in the middle and is not affected by magnetization, stand firmly on the table, and then the magnetism on the watch can be "sucked" by the iron block to restore the watch to normal. It is to use a magnetized iron can, the two ends are connected, and the magnetized love watch is put back in the iron can and can be demagnetized for 5-6 minutes.

It is recommended that you can open the warranty coupon attached to the watch under normal circumstances, and there will be a service address on the warranty coupon (B 2606, China Resources Building, Qianjiang Road, Hangzhou), or find a regular watch service center for testing and repair, etc., if there is a professional after-sales maintenance center nearby, it is also possible.

Hello, glad to answer for you!

During the warranty period, it will be sent directly to the counter for maintenance.

Shanghai, Beijing, and Hangzhou are all serviced, and you can call ** to consult after-sales maintenance services.

The simplest way to understand the essence of listening to a watch is actually to listen to the change in the sound of the watch when it moves after changing its position. In the case of a faulty or damaged watch, the sound of the watch will change significantly as the position changes. Some will change periodically, with louder voices and quieter sounds.

Because of this, listening to the watch can only detect whether the watch is faulty and does not fully represent the quality of the watch.

But for ordinary people, listening to watches requires experience, and it is best to make comparisons, that is, to listen more and practice more, and the sound of watches of different structures and sizes is not the same. Generally speaking, the male watch is louder, and the female watch is much quieter. As for the position of the listening watch, it is necessary to choose the usual position when wearing it - that is, the flat surface, which includes "on the face of the dial and under the face of the dial".

In addition, there are three façade positions: below the table handle, to the left of the table handle, and above the table handle, for a total of five positions.