TP LINK Router Model TL 402

IP address.

The should be 1 should be 0

Don't use the instructions on the manual, I'll do it this way.

Have you experimented with wo's method?,The phenomenon you said is exactly the same as my previous one.,You can go directly.,It's not okay to press the landing rover.,It's not sexual to find the manual setting.,In the end, I changed it.,It's OK!

First of all, check if the line is good.

Pin your machine's IP address to the same network segment.

It's fixed.

On the premise of ensuring that there is no problem with the line, set the IP of the machine to except 1). Gateway:

Turn on IE input again.

What is the IP of your computer?

Wouldn't it be nice to change to the same network segment as other computers...

IP and everything else are filled in manually.

It's true, the address of the telecom is in conflict with your route, and there's the hardware setting, haha.

3 The 4th floor is correct, and the appraisal is completed!5th floor (upstairs).

How to set up a wireless router:

1.The router is connected to the network.

2.The system is connected to the router.

Turn on the wifi of the computer, search for the default wifi name of the router (the nameplate on the back of the router is written), and connect to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Go to the gateway page.

Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface. (This interface will pop up automatically for new routes).

4.Set up a way to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband account password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

5.Set the wifi name and password.

Go to Wireless Security in the wireless settings, and select WPA2-PSK mode for security mode. Select AES for WPA encryption rule. Set up a wireless network key. The router will automatically restart after setting, please enter a new wifi password to connect.

6.The configuration is complete and you can enjoy the network.

TPLintL-WR740N has 4 LAN ports and 1 WAN port, which are marked with small English letters on the router's interface. The WAN port is used to connect the external broadband inlet network cable, and the LAN port is the connection between the intersection device and the computer. The blue ones are WAN ports, and the other four are LAN ports.

Routing settings.

Open the browser on the computer, I use Google Chrome here, enter in the address bar, press enter and the login settings interface appears.

Generally, the default user and password are admin, and the router settings interface appears after entering.

The current router is generally installed after entering the password setting interface, after setting the password, you will enter the setup wizard, click the setup wizard in the upper left corner, click Next The following dialog box appears, select PPPoE (ASDL virtual dialing):

Enter your account and password, the general initial password has its default in each place, and you need to provide it from the network operation provider. After completion, continue to click Next, since the author's route is wireless routing, the following figure is about wireless routing, if you are not a reader who uses wireless routing, you can skip this step.

In the red line area, set up a wireless connection, which is the password for the wifi. If you don't set it, it's easy to rub the net.

Finally, click Next to restart the route.

Hello! The TP wireless route setting method is similar to other route setting methods.

Here's how:

Connect network cables and routers to the home, and connect the routes to the host to ensure the normal operation of the network.

Open IE and enter it in the address bar.

Enter the corresponding account and password, and the account and password are admin to enter the setup wizard interface.

Select the Internet access method: PPPoE

Enter the password for the account given to you by the business hall.

Set a password for the wireless.

The last point is rebooted, and it works normally after 3 minutes.

Open the Internet Explorer browser on the desktop of the computer, clear the address bar and enter the default management IP address of the router), the login box will pop up after entering.

2. Log in to the management interface.

Enter the username and password in the corresponding places, and click OK. The default username and password are admin.

1. Start the setup wizard.

Once you are in the management interface of your router, click on the Setup Wizard, and then click Next.

2. Choose a way to access the Internet.

If you use the broadband account and password assigned by the operator to access the Internet via PPPOE dial-up, follow the instructions in this article to set up the Internet. If it is another form of Internet access, please select and refer to the corresponding setting process

If you don't know how to access the Internet, please click Reference:

Select PPPoE (ADSL Virtual Dialing) as the Internet access method, and click Next.

3. Enter the Internet broadband account and password.

Enter the broadband account number and password provided by the carrier in the corresponding settings box, and make sure that the account and password are entered correctly.

4. Set wireless parameters.

The SSID is the name of the wireless network (can be set according to actual needs), check WPA-PSK WPA2-PSK and set the PSK wireless password, and click Next.

5. After the setting is complete, restart the route.

Click Done, and the setup wizard is complete.

After the setting is complete, enter the router management interface, click Running Status, and check the WAN port status.

At this point, the network connection is successful and the router has been set up.