TP LINK WIRELESS ROUTER TL WR700N INTERNET ACCESS ISSUES

Look at your description It is recommended that you follow the step 2 router wireless routing mode, "online neighbors" in the router manual, set up "local connection", manually set up IP and DNS services, these 2 are set to get automatically, and then there is step 4 Set up the router inside, Rouetr Setup Wizard - Wireless Settings, set the Internet access mode and select PPPOE (ADSL virtual dialing) and then fill in the broadband account number and password, press"Next", and then press"Reboot"

If you can't use wireless to enter the routing settings,Then first use the network cable to connect the route to the computer,You can enter it in the browser,The account password is admin,That is, first plug the ** line into the modem,The line out of the LAN port on the modem is plugged into the router,And then this can only be connected with wireless ,,, if you set up the router first,It is to connect the router to the computer first (only 1 LAN WAN port),Not connected to the modem,Set up the route and the modem connection, then with Wi-Fi,

Here's how to set up a TP-Link wireless router:

1. After connecting the network cable, enter it into the router in the browser.

2. Click Setup Wizard in the left menu.

3. Then click Next on the page.

4. Then select the first option in the Internet mode.

5. Then you will enter the wireless setting page, the SSID is the WiFi name, the PSN password is the WiFi password, click Next after the setting is completed.

6. Click Finish, and the settings will take effect.

The operation method and steps for setting up the TP-Link TL-WR700N 150M router are as follows:

1. First of all, after confirming that the computer is connected to the router, enter "enter the router management page" in the browser, as shown in the figure below, and then enter the next step.

2. Secondly, after completing the above steps, on the left side of the TP-Link router management page, click on the "Setup Wizard" option as shown in the image below, and then enter the next step.

3. Then, after completing the above steps, click the "Next" button in the installation wizard to start the setup, as shown in the figure below, and then enter the next step.

4. Then, after completing the above steps, select the Internet Access method.

Here you can select the default first item, then click the "Next" button as below screenshot shown, and then go to the next step.

5. Subsequently, after completing the above steps, enter the wireless wifi name of the router in the SSID and select WPA-PSK

WPA2-PSK and set the password in the PSK password below as shown in the image below, and proceed to the next step.

6. Finally, after completing the above steps, click the "Finish" button for the settings to take effect as shown in the image below. In this way, the TP-Link TL-WR700N 150M router is set up and the problem is solved.

TP-Link TL-WR700N 150M Router Setup Method:

Select a route pattern.

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Hello, TP-Link TL-WR700N 150M wireless router defaults to AP mode, how do you use it, how to connect, talk about it.

The TP-Link TL-WR700N can be set up as follows

TP-Link TL-WR700N mini wireless router, there are currently 3 versions, namely V1, V2, V3; The v1 and v2 versions are completely the same in terms of settings, but v3 is different from v1 and v2 in terms of settings. So, before setting it up, check the version number of your TL-WR700N on the label at the bottom of the router.

<>3.First you need to enter the login password (there is a prompt on the back of the router), usually admin login.

4.The Setup Wizard will pop up by default, if it doesn't pop up, you can click the Setup Wizard on the right to set it.

5.Click on AP (Access Point Mode) to take a closer look at the application scope of the mode Next.

After the settings are completed, click Restart, the router will be automatically refreshed, and the settings will take effect.

7.Finally, plug the network cable into the router port and you're ready to enjoy Wi-Fi.

1. What is your IP address? Is it the router IP when you are in Shanghai?

2. You should restore the router to the default settings, that is, use a toothpick, paper clip, or ballpoint pen refill to press the button in the small hole behind the router to restore the default settings for one or twenty seconds. Then set up the router with the default IP login marked on the bottom of the router, generally, the username and password is admin

3. What you say "can be connected" is just that the computer is connected to the router, and the connection between the router and the network is abnormal. If the current network needs to automatically obtain IP addresses, you need to set the WAN port of the router to automatically obtain dynamic IP addresses. If your current network is dial-up, you'll need to set up dial-up for your router.

You have to change the dial-up username in the router.

You take a look at which DHCP server assigned your IP address. Then go into that server address. If you don't believe it, you can't get in unless the password is wrong. Local Connection status.

The following describes how to set up the TP-Link router:

1. After making sure that the computer is connected to the router, enter it in the browser to enter the router management page.

2. On the left side of the TP-Link router management page, click on the Setup Wizard.

3. Then click Next in the setup wizard to start the setup.

4. Then select the Internet mode, select the default first item here, and then click Next.

5. Then enter the wireless wifi name of the router in the SSID, then select WPA-PSK WPA2-PSK, and set the password in the PSK password below.

6. After all the settings are completed, click Done to make the settings take effect.

You need to use a laptop to set up the router, which is to find a laptop connected to the network cable.

First of all, open a web page, http; Enter the settings page (most routers have this address, see the manual for details) The username and password are admin, which is the router's settings page.

After powering on first, insert a small pin into a small hole in the router and let it reset to factory settings. The router is in AP mode by default, and you need to change it to routing mode to connect to the broadband modem. First set the IP address of the local computer to a static address, such as the last digit arbitrary), subnet mask, the rest do not need to be set, and then enter the default management address of WR700N, the default factory address of WR700 is The username and password are admin, after entering the management page, select the route mode in the wireless mode and then it will be restarted, and then set the IP address of the machine to be automatically obtained, and then enter the management page, and enter the account password of ADSL according to the setup wizard to connect to the Internet.

It's also a good idea to set up a wireless password and encryption mode.

You just go to the Setup Wizard and do it step by step.

The methods and steps to set up a TPLink wireless router and set a wifi password are as follows:

2) Then a dialog box will pop up, on this box you are asked to enter the username and password, generally the username and password are admin, (this wireless router is also marked above), the modern wireless router in this step is to ask you to set a password, and then enter the router settings interface, find the "setup wizard" or "basic settings" or "Internet settings" or "interface settings", according to the setup wizard, select the PPPOE mode, and then enter your Internet account and Internet password, 1Setup Wizard.

2.Enter your online ID and password.

3) Then set the wireless parameters WPA2 mode and WiFi password in the wireless network settings, and finally click Save, so that the wireless router will automatically restart, which means that the setting is successful.

1.Wi-Fi password settings.