Konka TV LED42F3700NF How to connect with computer TV

If it is wired, it is recommended that you connect the router through the cat, and the router is connected to the network cable interface of the TV, and the following are the steps for the TV wired connection for your reference: 1. Router setting steps: 1. The computer IP is automatically obtained, please check the computer manual or verify with the computer after-sales call.

2. Restore the router to factory settings and reset the router parameters. 2. TV setting steps: 1. Turn off the power of the TV and restart, 2. Menu-Settings-Network-Wired-IP Type Automatic Acquisition-Setting-Network Detection.

If it is wireless networking,Please turn on the built-in wifi of the TV,In addition, there are requirements for the setting of the wireless router,What our TV can identify the wireless router encryption is:(1)Adopt WEP encryption mode,Set as follows:Select the authentication methodOpen, WEPencryption select64bit, Select ASCII for the key mode, Set any one key,The password needs to be set5 digits。

2) Use WPA encryption mode, set as follows: the password type is TKIP, PSK EAP is PSK, and the password needs to be set to 8 digits.

It can be connected and used through VGA or HDMI interface,TV connection to computer Pay attention to a few points:1、The resolution of the computer should be within the range of the TV,The resolution of the TV can be viewed in the manual of the TV2、The refresh rate of the computer should be60Hz

3. Turn on the TV first, put the TV on the computer, VGA, PC (the signal source is switched accordingly, if the signal source is connected to the HDMI interface, the signal source is switched to HDMI), and then start the computer host to let the TV automatically identify the signal of the computer. (Note: Don't turn on the computer first and then turn on the TV, that may not have a picture) desktop computer, press the "F8" key on the computer keyboard when turning on the screen to enter the safe mode of the computer, turn down the resolution, and adjust it to the range of our TV.

Then press Apply and OK on the computer, and then restart the computer. (If the machine comes with its own application**) to install the software needs to be connected to the TVU disk,Use from the application that comes with the machine,Do not support the use of third-party software in other places**,If you need it, you can enter the official website**Consultation。 Thank you for your consultation and have a great day!

Konka TV LED40F1000 into computer mode, how can I connect w f pro, hello, I am happy to answer the <> for you

If you set Konka TV LED40F1000 to computer mode, but you need to connect to Wi-Fi, you can follow the steps below:1Open the TV menu, find the "Network" option in the "Settings" option, switch to the "Wi-Fi" option.

Select the Wi-Fi signal you need to connect to and enter the security password for that signal. 4.After waiting for the TV to receive a Wi-Fi signal and connect to the mountain, you can use the TV to browse the Internet or connect to other devices.

2.Try moving your Wi-Fi router closer to your TV to boost the signal strength. 3.

Confirm whether the Wi-Fi router is working properly and whether you need to restart it. 4.Check if there are any other devices interfering with the signal between the TV and the Wi-Fi router and try to remove the source of interference.

If you still can't connect to the Wi-Fi signal, it is recommended that you contact Konka TV customer service for further technical support.

1. Turn on the TV after playing, press the menu button of the remote control, and pop up the menu options of the TV.

2. Find the system settings, select it and press the confirm button to enter.

3. After entering, find the system upgrade, select and press the confirm button to enter.

4. After entering, select **Upgrade, press the confirm button to start the network to check the update, if the server has an upgrade package available, the system will prompt that there is an upgrade package to be**, select immediately**, press the confirmation key to start**, **After completion, the system will prompt whether you need to upgrade, select Yes, press the confirmation book reputation key to start the upgrade.

5. After the upgrade is completed, the TV will automatically restart, and it can resume normal use after restarting.

Find customer service to be able to upgrade. View the original post

I'm similar to your problem, after connecting to the line, although the network IP is automatically obtained, the network still doesn't work. The after-sales service is not clear from the **, and they did not come to the door, so I must prepare what router first.

The TV can only automatically get the IP, then the cat will also be automatically IP.

You have to install a router, and you must have a professional to debug itBecause the TV doesn't have a dial-up function.

To pass through the router, you also need to buy a wireless network card on the TV.

Hello: Go to the computer city and buy an HDMI to VGA connector, and you can connect it. LED42F2200NF TV was produced in early 2012, and its interface is not as complete as it is now.

According to your feedback, Konka LED48F3700NF TV can be used with wired or wireless networking.

Wired networking: 1. After the router is successfully set up to network, enter the TV application interface—select the "Settings System Settings" option—network—wired—IP connection mode is selected as "Auto Acquisition"—select the "Settings" option on the interface to confirm - prompt "Wired network is connected"—and then select "Network Detection" on the interface to confirm;

2. After the router is set up and connected to the network successfully, enter the TV application interface, select System Settings, Network Connection, Active Network, Switch, Wired Network, IP Type, Automatically Obtain, and Confirm.

Please refer to the display on the interface.

Wireless connection: 1. Wireless connection needs to be matched: wireless network card (wireless network card needs to be purchased and matched by the user, if the built-in wifi does not need a wireless network card), wireless router, computer, network TV.

2. After the wireless router and the computer can be connected to the network normally, please connect the wireless network card to the TV (no driver, can be installed and used directly).

3. TV menu-Network Settings-Wireless Settings-SSID(Search for router devices)、Encryption type(Same as set on the computer)、IP typeSelect automatic getting,Finally, click Settings。

In addition,The wireless router settings that our TV can recognize are:Adopt WEP encryption method,The settings are as follows:The authentication method is selected as Open, WEP encryption is selected64bit, the key mode is selected ascii, any key can be set, and the password needs to be set 5 digits。

Alternatively, use WPA encryption and set the following parameters: set the password type to TKIP, select PSK EAP to PSK, and set the password to 8 digits. Passwords are recommended to be purely numeric.

Konka enterprise knows that to provide you with high-quality solutions, attentive to answer your questions, hope to be able to get you.