Can anyone tell me what is the size of the virtual twist memory?

Press System Default. Doubled it again at the maximum.

For example, with 256M memory, the virtual memory will be between 384 and 768.

Then make 768 into 1500 or so.

Mine is to set the original default to the original double, it can be used all the time, and there is nothing bad about it.

From what you provide, it is estimated that your machine is not very new, that is, there will be many reasons why playing DNF is very stuck, if your machine can't meet the basic requirements of DNF, then it is useless for you to add internal bend training, because the performance of the machine does not depend on the memory! --For your question, what I want to tell you is that adding memory still has a certain effect, and it is just not big! --If you are under a single (should be 512M) memory, if you add one more and the model of this memory, it is best to have the same parameters as 512M memory, then it is possible to increase the speed of the whole machine by about 5%, this is not because of the memory capacity, but 2 memories to form a dual-channel working mode, the speed of the theoretical memory is doubled, but the whole is only the value of the above answer!

You are the memory of 384. I won't say anything else, let me tell you first, you may be an integrated graphics card or an overclocked graphics card and then 512 memory, divide the memory to the video memory, it is also possible, you have an independent graphics card, and it is pure, but your memory is 256MB+128MB The two independent memories are frequency-split, DDR 333,400, it belongs to a generation of memory grips, old-fashioned, DDR533,800 belongs to a new point, the corresponding DDR1333 is the latest, the frequency is not the same, The price will naturally not be the same as the section type shed,The same memory size,The greater the frequency,The better the memory effect,But it's not that you can just plug in a DDR1333,It also depends on what model your motherboard can be plugged in,Generally look at your machine now only display384MB,I estimate that it is a generation,A generation of 512MB memory is about 70-100 yuan to rent and buried,1G is about 200 yuan。

It's time to change the computer, the configuration is too low. 1G memory module is about 100.

You can set the virtual memory, and the memory is about 200-300.

It is recommended to set the initial size and maximum value to 1-2 times of your physical memory at the same time, for example, your physical memory is set to 4608MB for 3G (3G memory is a time, the initial size and maximum value should be set consistently, and it is not enough to increase it appropriately).

To set up virtual memory, right-click on My Computer Properties Advanced Performance Settings Advanced Changes in Virtual Memory Select a custom size, set both the initial size and the maximum value, and set it to 1-2 times your physical memory. If you have 3GB of RAM, set both the initial size and the maximum to 4608MB.

After setting up, you need to press the "Settings" button, then press OK and Apply, and restart the computer settings to take effect.

Target. However, your memory may be 4G, but it can't be recognized by the 32-bit system. That virtual memory doesn't need to touch him, 2G is enough.

Physical memory (installed memory sticks), virtual memory can be done by simply clicking "Settings(s)" in the "Virtual Memory" window in the image above.

DDR memory models are DDR 200MHz DDR 266MHz DDR 333MHz DDR 400MHz DDR2 Memory models DDR2 400MHz DDR2 533MHz DDR2 667MHZ DDR2 800MHZ DDR2 1066MHZ 3200=DDR 400, 2700=DDR333, 2100=DDR266 There are early Yes, now it is available on the market. Some manufacturers with strong R&D strength have already released 1600, but the cost of DDR2 memory frequency is difficult to control as soon as it exceeds 800, so there is no need to pursue too high a frequency, just enough. DDR has 400MHz, DDR2 has , DDR3 has 1333, you first have to distinguish what kind of memory your computer uses, which will be indicated in the manual, whether to use D1, D2 or D3 There is also a point to remind that if it is of the same generation, such as D2, because the interface is the same, you can consider buying a slightly higher frequency than the motherboard support, which will not affect the use and change to the motherboard overclocking, if you are a computer DIY.

For example, my computer supports 667 memory, I bought 800 memory, and now I am overclocking, so I don't have to overclock the memory alone, because the default frequency of the memory is 800.

The most critical thing is how much your memory is not said.

Set at C, your C is big enough.

256 memory settings 400 700

Right-click on the My Computer property Advanced Performance - Settings Advanced to change, you see what your physical memory is, set it to the minimum multiple of the physical memory, and the maximum value is 3 times. If your RAM is 256MB, set it to a minimum of 400MB and a maximum of 700MB

Click Set, OK, Restart.

It is best to set it in the C drive, because the C drive has the fastest access speed.

The size is set to a multiple of your physical memory, with the maximum and minimum values the same.

That's it.

Located on the C drive. It's twice as much as your physical memory.

Microsoft recommends that the minimum and maximum values be set to multiples of the physical memory.

It is recommended to use partitionmagic to change the partition table to make a partition for page files. (Benefits.)

Yes: no fragmentation, so it doesn't affect the speed of reading and writing other files and page files) That's what I did.

The virtual memory size allocation is as follows:

cpu>1gmhz, 128m：200-300mcpu>, 256m: 150-200m

cpu>1gmhz, 256m：150-300mcpu>2gmhz, 512m: 30-100mcpu>, 128m：300-500m

Virtual memory is used by Windows to use page files that exist on the hard disk as memory. The virtual memory value is usually set to a multiple of the physical memory. It's better to set the virtual memory in a partition that is not the same as the system shopper, because the virtual memory should change dynamically in use, which will produce disk fragments and shadow dust to call the system running speed.

It's good to set it to a fixed 3072. Both the largest and the smallest are the same. It saves time in resizing pages.

Lowest times of physical memory, highest times.

Cancel the check, and then click Custom, initial 2048, maximum 4096, select D, E, F disk do not choose C disk, because the virtual memory will establish a large capacity of the swap file, and then click on the settings, that is, the meaning of saving, if you don't click, the settings just now are invalid, and then click OK

Theoretically, the maximum value can be twice that of the physical memory, and you can set both the maximum and minimum values to 512 to improve the speed of the system

Fill in 3080 for both valuesVirtual memory is actually to take out a part of the hard disk space to use as memory, when the memory is occupied, the computer will automatically call the hard disk to act as memory, in order to relieve the tension of memory. For example, if the physical memory is more than 512MB, you can set the maximum and minimum values of virtual memory to 5 times.

Your physical memory is 2G, so it is recommended to fill in 3080 for both the minimum and maximum virtual memoryThe reason why the minimum and maximum values are the same is to better improve the read and write speed.

The virtual memory setting method is: right-click on My Computer - Properties - Advanced - Performance Settings - Advanced - Virtual Memory Change - Select the system drive letter in the drive list - Custom size - Set the values in "Initial Size" and "Maximum", then click the "Settings" button, and finally click the "OK" button to exit.

As for choosing a C drive, D drive or E drive, I recommend choosing C drive, and choosing other disks is easy to delete cache files by mistake.

I don't know how to ask me.

Set the virtual memory according to the size of your physical memory, for example, 3G can be set to multiple of the physical memory, first press 1 times to set, if it is not enough, it will prompt you, set it in times. 3072--4608 (the initial size and maximum value must be the same).

To set up virtual memory, right-click on My Computer Properties Settings in Advanced Performance Advanced Changes in Virtual Memory Select Custom Size and add 3072 or 4608 MB to the initial and maximum sizes. After setting up, you need to press the "Settings" button, then press OK and Apply, and restart the computer settings to take effect.

It's hard to say. There is no score, depending on what you think. 3G, ordinary people are enough.

If you want your computer to be more responsive, don't set up virtual memory. Because virtual memory is actually used in the capacity of the hard disk, reading data from the hard disk is definitely slower than the memory. Virtual memory is the best thing to set only when you're sure you don't have enough memory to overhead.

If you set up virtual memory, then when the program runs, it will allocate a part of the physical memory (your memory stick) and a part of the virtual memory (which affects the response speed).

If you still want to set it, it's usually best to control it between 1 times, but you can also set it bigger (you can set it as much as you want to the partition disk). This will slow down the speed of response). It is recommended not to set the virtual memory on the system disk.