What should I do if the 17 inch LCD screen shows out of range when I open the game?

First, if the host power is turned on, it will prompt that the display frequency is out of range, and the best way is to clear the CMOS and make sure that the connection is normal. Both of these have the potential to raise the questions that the landlord said.

Second, if the display frequency is out of range after entering the XP, then the refresh frequency in the display properties is too high to cause the display to be asynchronous, the solution is to press F8 to enter the safe mode when starting the XP, right-click on the desktop - Properties - Advanced - Settings - Monitor to adjust the refresh rate to 60, the resolution to 640*480, and set it to normal value after starting it again. Or just disable the graphics card driver, reboot it to the system, and then enable the graphics card driver, so that you can adjust your resolution and refresh rate to ensure that you are OK.

Of course, sometimes there will be a problem that the refresh frequency is set to 60 and the display frequency is set too high, this problem is very rare, it may be 1, ATI graphics card, sometimes the display attributes of Windows cannot be adjusted; 2. The connecting line is not connected, and the frequency signal is incomplete; 3. Graphics card problems. It's best to reinstall the graphics driver and give it a try.

1137328107 Hello, 1. Please confirm whether the refresh rate of your computer is below 75Hz, because the LCD monitor can only work below 75Hz, and the general standard can be set at 60Hz. 2. You can try to upgrade the driver of your graphics card, you can go to the latest driver of the relevant graphics card, so as to improve the performance of the graphics card.

Benq Superman.

The computer screen is out of range because the output frequency of the computer does not match the receiving frequency of the monitor.

Solution: Adjust the resolution of the active signal on the computer.

The detailed operation steps are as follows:

1. First, right-click on the screen and click on "Screen Resolution" in the menu that appears.

options, as shown in the image below.

2. Secondly, in the interface entered after completing the first step, click the "Advanced Settings" button as shown in the image below.

3. Next, click on the "List All Modes" button as shown in the image below.

4. Finally, find the resolution suitable for your computer monitor under "List All Modes" and click the "OK" button to solve the problem as below screenshot shown.

If the output frequency of the computer does not match the receiving frequency of the display, the resolution of the active signal on the computer can be adjusted.

The specific method steps are as follows:

1. Click the screen with the right mouse button, and then click the screen resolution button in the menu to enter.

2. Click the Advanced Settings button in the interface after completing the first step to enter.

3. Click the list all modes laugh button in the interface you enter after completing the second step.

4. Find the resolution that suits your computer monitor in all modes, and then click OK.

When a computer monitor displays "out of range", it is usually because the computer is outputting a resolution or refresh rate that is beyond the monitor's supported range, causing the monitor to not display the image properly. This usually happens in the following cases:

Change your computer's display settings: When you change your computer's resolution or refresh rate, you'll see an "out of range" prompt if you select a setting that is outside of what your display supports.

Replace display: When you replace a display, you will also be prompted if the new display doesn't support the resolution or refresh rate that the old display supports.

Graphics card issues: Some low-end graphics cards may not support higher resolutions or refresh rates, which can also cause the issue.

Here's how to fix it:

Enter Safe Mode: You can try to enter Safe Mode and then change the resolution and refresh rate to the range supported by your display.

Modify display settings: If you can see the desktop, you can change the resolution and refresh rate by modifying the display settings. Open the slight.

Replace your monitor: If your new monitor doesn't support the resolutions or refresh rates that your old monitor supports, you'll need to replace your monitor or upgrade your graphics card.

Upgrade the graphics card driver: If it is caused by a problem with the graphics card driver, you can try to upgrade the graphics card driver.

If the above methods cannot solve the problem, it is recommended to contact the computer maintenance personnel of the jujube industry for maintenance.

Monitor display "out of range" solution: This problem is caused by the resolution or refresh rate in the display properties being turned up too high. Here's how to fix it:

After powering on, press the F8 key when the self-test is completed, the advanced boot menu will appear, select "Last correct mode", if you can enter the system, then the system has been automatically restored. If you can't enter the system, reboot and press the F8 key, the advanced boot menu will appear, select "Safe Mode (SOFE Mode)" or "VGA Mode" Enter, after entering the system, right-click on the blank space of the desktop and press "Properties" The "Display Properties" window appears Guess the "Settings" page Adjust the resolution to 1024x768(17"Monitor) Press the "Apply" button Press the "Advanced" button in the bottom right corner The Display and Graphics Card Properties window appears Select the "Lift Monitor" page in"Hides the mode (h) that cannot be displayed by this monitor"Put a hook on the front Press the drop-down arrow on the right side of the box under "Screen refresh rate (s)" Select the maximum value All the way to OK, and restart it.

If you can't get into "SOFE mode" or "VGA mode", you have to reinstall the system.

"Out of range" means that the computer monitor is receiving a signal that is beyond its support range, resulting in a failure to display properly. This is usually the case when the resolution or refresh rate is not set properly.

If your display doesn't support your computer's output resolution or refresh rate, your display will display a black, blurred, or "out of range" warning message. In this case, you need to manually change the resolution or refresh rate of your computer so that the early state is within the range supported by the monitor, so that the display can display normally.

The specific operation method can be set according to different computer systems, and can usually be set by the following steps:

Turn on your computer and go to the display settings.

Select the Resolution and New Rate options to view the resolution and refresh rate of the current settings.

Depending on the specifications of your monitor, choose a supported resolution and refresh rate.

After confirming the changes, keep the finger saving settings and exit.

If the above methods don't work, it may be that the monitor or computer graphics card is faulty and needs to be repaired or replaced.

Beyond the range that the monitor can display,You can find a monitor that can show painting,Then turn down the resolution and refresh rate,Then connect this monitor,Pin or restart the computer press F8 to enter the security loss code elimination mode and uninstall the graphics card driver after restarting the computer,Remember to reinstall the graphics card driver and reinstall it。

The computer screen is out of range because the output frequency of the computer does not match the receiving frequency of the monitor.

Solution: Adjust the resolution of the active signal on the computer.

The detailed operation steps are as follows:

1. First, right-click on the screen and click on the "Screen Resolution" option in the menu that appears, as shown in the image below.

2. Secondly, in the interface entered after completing the first step, click the "Advanced Settings" button as shown in the image below.

3. Next, click on the "List All Modes" button as shown in the image below.

4. Finally, find the resolution suitable for your computer monitor under "List All Modes" and click the "OK" button to solve the problem as below screenshot shown.

Hello dear, the monitor says "out of range." Workaround:

This problem is caused by the resolution or refresh rate in the display properties being turned up too high. Here's how to fix it:

After powering on, press the F8 key when the self-test is completed, the advanced boot menu will appear, select "Last correct mode", if you can enter the system, then the system has been automatically restored. If you can't enter the system, reboot and press the F8 key, the advanced boot menu appears, select "Safe Mode (SOFE Mode)" or "VGA Mode" Enter, after entering the system, right-click on the blank space of the desktop and press "Properties" The "Display Properties" window appears Select the "Settings" page Adjust the resolution to 1024x768(17"Monitor) Press the "Apply" button Press the "Advanced" button in the lower right corner The Display and Graphics Properties window appears Select the "Monitor" page in"Hides the mode (h) that cannot be displayed by this monitor"Put a hook on the front Press the drop-down arrow on the right side of the box under "Screen refresh rate (s)" Select the maximum value All the way to OK, and restart it.

If you can't get into "SOFE mode" or "VGA mode", you have to reinstall the system.

What system? Recently it was not updated with a patch from Microsoft. Microsoft's patch will cause a lot of game and picture rendering program errors,Windows 7 and Windows XP users install MS13-057 security update (KB2803821 and KB2834904 respectively) to remove this patch,Try,If it doesn't work,Uninstall the graphics card driver,Try it again,See if the resolution and refresh rate in the game are abnormal。

Maybe there was a problem when restoring, uninstall the previous Wushuang, remove the residual garbage, and try to reinstall it.

There isn't enough video memory. Let's change the graphics card.

Summary. If you make do with it, you can lower the resolution and give full play to the performance of the graphics card, and if you are comfortable, you can change the monitor, and the computer monitor appears out of range, what does it mean? Is it a problem with the graphics card, or is it a problem with the monitor?

Hello, yours I have seen, the code word takes time, please wait a moment, thank you.

The problem with the display is simply that the graphics card says I want to display 4K, but the display performance is only 2K, so this problem arises.

Is there any way to fix it.

Is there any way to fix it.

Make do with it, turn down the resolution, give full play to the performance of the graphics card, change the monitor if you are comfortable, and connect to the network set-top box with 12 inches.

Make do with it, turn down the resolution, give full play to the performance of the graphics card, and change the monitor if you are comfortable

Out of range means (out of range) because the display resolution or refresh rate is set too high.

Workaround: (Click below, you're good to go).

Setup Steps: Press the F8 key to enter safe mode before entering the system and reinstall the display driver.

The refresh rate is set to 85hz 75hz

The resolution is set to 1024*768

Reboot. Everything is back to normal, summarizing the cause of this issue: the display resolution or refresh rate is set too high.

Enter Safe Mode, (Safe Mode).

Right-click on the desktop Properties, Settings, OK, OK, OK, and Restart.