The distance of the AutoCAD offset line does not match the measured distance

Updated on physical education 2024-02-09
13 answers
  1. Anonymous users2024-02-05

    1.Maybe the default unit you set isn't SI, but inches or something.

    So you enter 55 not 55 mm.

    Tool-SettingsOption.

    The easiest way.

    Enter the Offset command o, enter the distance containing the unit 55mm and then offset)2If you use the offset command o instead of co, you may be affected by dynamic snapping and the orientation limitations of the F8 function key.

  2. Anonymous users2024-02-04

    The measured distance is not the same as the value of the offset The reason may be that the point you captured is not open and the result is not accurate enough, but at most it will not be much different, like you said the offset is 1200 The measured is 120000, which should not be!!

    I tried it myself, and it's not a problem with the unit setup. So I suggest you re-check your own operations.

    One of the things that can happen to you is that you scale the original graph by a factor of 100, but it doesn't have anything to do with offset.

  3. Anonymous users2024-02-03

    First of all, if you are using genuine AutoCAD! Generally, there will be no such problem! You turn AutoCAD off and back on, and then draw the pan 1200, if the number is still 120000!

    It is recommended that you also look at the number there "that your AutoCAD is bad!

  4. Anonymous users2024-02-02

    1. First of all, open the main interface of CAD software and draw the figure to be offset.

    2. Select the CAD offset tool or enter the CAD offset command o and press the enter key to confirm.

    3. At this time, enter the offset distance in the CAD command line and press enter.

    4. Click in the CAD window to select the object you want to offset.

    5. At this time, the radius of the circle will be expanded by 50, and if it is a CAD straight line, it will be directly offset by 50, and it is completed.

  5. Anonymous users2024-02-01

    It is very likely that the drawing you measure is a local detail, and then the scale used by the drawer is not 1:1000, there may be data discrepancies.

    If it is a multiplier relationship, it is a matter of proportion, then the name of the detail is there, and the author should indicate the scale he uses.

    For example, in the figure below, it is 1:20, then the relationship between the data you measured and the actual data should be 50 times.

  6. Anonymous users2024-01-31

    Summary. If the CAD cannot continuously offset different distances, the specific reason is that the dimensions are not the same, which is caused by an operation error. Here's how to solve it

    1.First of all, the offset is used to move a straight line or a figure by a certain distance. There is a square in the picture below!

    2.Dear, the next thing is to set the offset module in the menu on the right, you can click on it to adjust it! 3.

    Click the offset command, and you first need to specify the offset distance. According to the actual scale of the drawing and the requirements of the drawing, we can enter 150, and the unit is 4 mm by defaultKiss, and then you have to press enter to determine the offset distance.

    Next, we need to select the offset object! 5. Kiss, then specify the direction of the offset, use the mouse to determine, click any point on the right with the mouse, it is a special offset to the right, and vice versa! 6.

    In this way, in the end, we can complete the offset operation as long as we need the same offset distance, and then perform the continuous offset operation. In this way, we can complete the renderings!

    What should I do if CAD can't continuously offset different distances.

    If the CAD cannot continuously offset different distances, the specific reason is that the dimensions are not the same, which is caused by an operation error. Here's how to solve it:1

    First of all, the offset is used to move a straight line or a figure by a certain distance. There is a square in the picture below! 2.

    Dear, the next thing is to set the offset module in the menu on the right, you can click on it to adjust it! 3.Click the offset command, and you first need to specify the offset distance.

    According to the actual scale of the drawing and the requirements of the drawing, we can enter 150, and the unit is 4 mm by defaultKiss, and then you have to press enter to determine the offset distance. Next, we need to select the offset object!

    5. Kiss, then specify the direction of the offset, use the mouse to determine, click any point on the right with the mouse, it is a special offset to the right, and vice versa! 6.In this way, in the end, we can complete the offset operation as long as we need the same offset distance, and then perform the continuous offset operation.

    In this way, we can complete the renderings!

    Kiss, the specific diagram reference steps are as follows!

    Dear, in general, the problem of CAD continuous offset unequal distance is a long-term problem, you can ignore it, you don't need to exit the program. Yes, it can be operated directly. Because, CAD continuous offset is not a big problem, it may be a small problem in the middle of the program, it can be operated and used normally!

    Don't worry about it!

  7. Anonymous users2024-01-30

    o - Space - Enter data - Space - Click on the line - Click on any point in the direction of the offset - OK Is that how you offset? Be sure to measure vertically!!

  8. Anonymous users2024-01-29

    The distance of the offset is not accurate, there are two options when offset, one is to directly enter the value in the distance is how much you want to offset, and the other is to pass, generally used to use it with the capture function of F3. If it doesn't work, check whether the object you are offsetting is a line on the same plane, if it is a spatial 3D line offset, there will be a problem.

  9. Anonymous users2024-01-28

    Note the setting units in mm, cm, or ?

  10. Anonymous users2024-01-27

    What is the state of inaccuracy, that is to say, what state of deviation!

  11. Anonymous users2024-01-26

    Summary. Hello dear! Open CAD and locate the Offset command.

    That is, count the 4th from top to bottom. In CAD, the offset command is very common when we draw, which means that the line you draw (whether it is a straight line, arc line, or oblique line) can be offset by the same distance to the place you need to specify. For example, if I draw a line, I want to continue to draw a lot of lines, and the line I need to draw is a certain distance from the line I am drawing now, and it is also a straight line of the same size, then I use the offset command to draw, and I can quickly draw the next line.

    Hello dear! Open CAD and locate the Offset command. That is, count the 4th from top to bottom.

    In CAD, when we draw a drawing, the offset command is not common, it means that the line you draw (whether it is a straight line, an arc, an oblique line) can be offset by the same distance to the place you need to specify. For example, if I draw a line, I want to continue to draw a lot of lines, and the line I need to draw is a certain distance from the line that I am drawing now, and it is also a straight line of the same size, then I use the offset command to draw, and I can quickly draw the next line.

    How to use: Left-click on the "Offset" command, then enter the size of the offset, hit the pin spacebar, left-click on the line that needs to be offset, root the argument according to the direction you need, move the mouse up or down, click the left button, and the line has been offset. If you need to offset more than one line, just keep clicking on the line you want to offset.

    Related information: First open the AutoCAD drawing software and enter the main drawing page. If we want to use the offset function, it is to offset a line by a certain distance to meet our drawing requirements.

    I'm offsetting 344, and it's marked with yes.

    Pro-code search, hello! How to solve the problem of CAD offset size? In CAD drawing, in general, the actual offset size is proportional to the set size.

    When specifying the offset distance, try to enter a numeric value, and if you want to draw a line to indicate that the distance is missed, you should pay attention to the correct selection of the snapping object. 1.Start and run the Xunjie CAD software to enter the software drawing interface.

    Click on the "File" - "Open" option in the menu bar, and select the required CAD drawing in the opening pop-up window2Enter the command "d" command on the command line. Activate and enter the Dimension Styler dialog box.

    In the Style column on the left, select the style you want to modify. Here we take the "ISO-25" style name as an example, and then select the "Modify (M)" button on the right.

  12. Anonymous users2024-01-25

    Summary. Hello, after entering the distance value in CAD, the moving line is not perpendicular to the original line, and F8 should be opened.

    Hello, after entering the distance value in CAD, the moving line is not perpendicular to the original line, and F8 should be opened.

    1. Turn on the orthogonal function of CAD, family or press the shortcut key F8 to open, in this case, the straight line drawn must be straight; 2. If it just looks like a straight line is jagged, this is normal, but it must be straight when it is printed, and this situation can be ignored; 3. When drawing a straight line, it is not parallel or perpendicular, for example, a diagonal line may appear as shown in the figure above; Note that if the orthogonal function is turned on, it is still not straight, which may be caused by the following reasons: 1. The two ends of the straight line are not in a straight line, and there is a certain deviation grip difference that will lead to this situation; 2. The problem of computer monitors, sometimes the fineness of the display also directly affects the actual effect seen by the human eye, and this situation will not be jagged when printed, but it looks uncomfortable; 3. If the mesh snapping function is turned on, it may also cause the straight lines drawn to be not straight, and even if the orthogonal function is turned on at this time, there will still be a situation where it is not straight.

  13. Anonymous users2024-01-24

    1. Open the AutoCAD2007 version of the software on the computer.

    2. After opening the CAD, click Format in the toolbar, and then select the callout style in the format.

    3. Enter the Label Sample Sock Scale Manager, select the current style, and then click Modify.

    4. Enter the Modify Dimension Style page and click Count Modified Text.

    5. Enter the text page and modify the distance from the dimension line offset in the text position.

    6. After the modification, return to the annotation style manager, and click Set Royal Match as current to disassemble it.

Related questions
10 answers2024-02-09

The farthest distance in the world - Rabindranath Tagore. >>>More

6 answers2024-02-09

The Earth's orbit around the Sun is not circular, but elliptical, so it produces perihelion and aphelion, which are taken as the average distance of 150 million kilometers Astronomical means that the average distance of the Earth from the Sun is about 150 million kilometers, and if the eccentricity is equal to zero, it represents a circular orbit (e = 0). >>>More

11 answers2024-02-09

This involves basic limit thinking. The answer is just as much. >>>More

41 answers2024-02-09

The farthest distance in the world is not the distance between life and death, but I am standing in front of you, but you don't know that I love you, and the farthest distance in the world is not that I am standing in front of you, but you don't know that I love you, but I love to the point of obsession, but I can't say I love you.