What should I do if the yellow light of the ABS on the meter is on???

The instrument indicator light is yellow, first check the power supply fuse of the dashboard, if it blows, it needs to be replaced. Disassemble the dashboard, the lights are generally at the back of the dashboard, replace the lights that are not lit, and generally the individual lights are not lit to indicate that there is no problem with the fuse and wire, the main reasons are as follows

1. The lamp of the dashboard is damaged and needs to be replaced in time;

2. If the power supply line of the dashboard is broken, there is an open circuit or short circuit, which will also cause the car dashboard to not light up;

3. If the power supply fuse of the car dashboard is broken, there will naturally be no power supply, and the dashboard will not light up.

Precautions in the use of the car dashboard:

1. When the indicator light is on, the odometer should be observed immediately, if the cumulative mileage reaches or exceeds l00,000km, the timing toothed belt must be replaced, otherwise the timing toothed belt may break, so that the engine can not work normally.

2. After replacing the new timing toothed belt, it is necessary to open the rubber plug outside the reset switch on the mileage dial, and press the reset switch inside with a small round bar to extinguish the indicator light of the timing toothed belt.

3. After replacing the new timing toothed belt, remove the odometer and adjust all the readings on the odometer to the 0 position.

If the horn still does not sound, it means that the horn is faulty; If the horn sounds, it means that the horn relay or button is faulty.

1. Correctly distinguish between normal and abnormal sounds.

The vibration of each mechanism in the work of the car will emit a variety of sounds, but the sound does not mean that the car is faulty, in order to avoid unnecessary disassembly, we must first distinguish between normal sound and abnormal noise. The normal vibration sound of each system component (such as the noise on the surface of the engine), the impact sound of the gear when shifting, the air intake sound and exhaust sound of using gas as the working source, and the gear meshing noise are all normal sounds. Abnormal noise (abnormal noise) can be divided into slight noise, general noise and malignant noise according to the impact on the performance of the car.

Slight noise, such as the flashover sound of high-voltage electric leakage, the slight loose sound of rolling bearings, etc., the general volume is small, the degree of wear of the parts is not large, and there is no significant change for a long time, and this kind of fault can still maintain the normal operation of the car without repair.

2. When diagnosing abnormal noise of automobiles, attention should be paid to creating good auscultation conditions and trying to eliminate the interference of other noises, so as not to affect the accuracy of judgment. It is best to consciously amplify or reduce the sound, that is, use a screw or other metal rod as a stestological instrument to contact the sound part to amplify the sound, or use a single cylinder fire cut-off to reduce the sound to meet the diagnostic needs. The auscultation site should be kept quiet to minimize human interference.

The ABS yellow light on the instrument is on, indicating that the brake ABS anti-lock braking system is faulty, drive carefully to the auto repair shop, use the computer detector to read the fault code, and see if there is a problem.

The possible reasons for the ABS light to turn on are as follows:1Wheel speed sensor malfunction.

Line DU is faulty. Pump and pressure regulating solenoid DAO valve are faulty. computer malfunction.

ABS light on means that there is a fault in the ABS system, the ABS system may stop working, maybe your car will be the same as without the ABS system, the braking effect of the car will deteriorate, the braking distance will increase, the handling performance of braking will deteriorate, etc., so when the ABS light is on, the fault should be eliminated in time.

This is that there is a problem with the braking system, you need to check this thing, otherwise there is no way to continue to use the car, do you say?

The ABS fault light of the car instrument is lit, and this reason is the most common.

Summary. Dear, this question is up to me, it takes a little time to type, please be patient, thank you!

What should I do if the yellow light of ABS on the meter is on???

Dear, this question is up to me, it takes a little time to type, please be patient, thank you!

Hello, this light means that the brake system has a problem, the height is more common is the fault of the wheel speed sensor, you can read the brake system punch brigade system fault code to see if the speed sensor failure of which wheel is reported and then check the base of the town.

I went to read it, and it showed a problem with the line.

There is no wheel issue shown.

Is there any fault code ** or the like can be sent to see, the line fault may also be the wheel speed sensor, the corresponding check is OK.

At the beginning of the failure, the ABS turned on the yellow light when the cold car started, and after driving a few kilometers and turned off the ignition, it was restored, and it was always on after a few days.

Regardless of this phenomenon, the fault code will definitely be reported if the light is on, and the direction of the report will be checked.

Do you want to go to a 4S shop for repairs?

Thank you. Good.

Here's why the ABS yellow light on the dashboard is lit:

Reason 1: The sensing part of the ABS speed sensor is covered by pollution sources such as soil and mud, which affects the sensor to sense the corresponding speed signal, so that the ABS computer method cannot judge the vehicle speed, the wheel slip rate, and the corresponding action command cannot be issued to adjust the braking.

Solution: Clean the dirt on the speed sensor, adjust the gap between the speed sensor and the signal circle, and you can restore the normal sun.

Reason 2: The signal is poor due to the loose connection of the system line, and the system failure is caused by the poor contact of the ABS relay. The most common fault is that the speed sensor wire is loosely plugged in, which will show that the speed sensor signal is bad in the fault memory of the ABS computer.

Solution: Check the line connection spike and, there is loose reconnection.

How to deal with the yellow light of the dashboard ABS all the time? The ABS light turns yellow, indicating that the braking system of the car has failed, and the ABS system has failed during the driving process of the car. The solutions to cause the ABS light to turn on are:

1. If the battery voltage is too low, check whether the battery voltage is in the line fault, check the relay and ABS control line, and check whether there is a wire breakage, loose interface, and the relay is not installed firmly. 3. Check the liquid level height of the liquid reservoir of the brake master cylinder, if the liquid level is too low, you need to add brake fluid to make the liquid level height reach the normal value. 4. If the speed sensor is faulty, check whether there is any foreign object in the four speed sensors.

5. Check whether the fuse is blown or not. If the ABS light on the dashboard is always on, the ABS system of this generation of staring watches has failed, and the riders need to repair it immediately. The ABS system is an anti-lock braking system on automobiles, which prevents the wheels from locking up during emergency braking.

If the wheels lock up during emergency braking, the car will slip out of control, so that the driver can neither control the trajectory nor slow down, which is very dangerous. The ABS system can be used in the event of emergency braking @2019

This situation indicates that the anti-lock braking system and engine failure of the vehicle are recommended to be checked and repaired in time. When the vehicle is energized or ignited normally, the vehicle will enter the system self-test program, and the ABS light will be turned off after the test is completed. If the lights do not go out when the vehicle is energized or ignited, or if the lights do not turn on when the vehicle is moving, it indicates that the vehicle's ABS system is faulty.

When the car is driving, if only the ABS warning light is on, it means that there is a problem with the ABS system, and we can brake normally. At this time, we need to go to a professional car repair shop and ask a professional to repair it. If the vehicle's ABS system and braking system light up at the same time while driving, it means that there is a problem with the vehicle's ABS system and braking system, and the driver needs to check the brake fluid level.

If the brake fluid level is low, it means that the vehicle cannot continue to drive. If the brake fluid level is normal, it may be that the vehicle's ABS system is faulty, drive cautiously and send it for inspection and repair as soon as possible. The following items should be examined:

1。The line connection between the vehicle's wheel speed sensor and the control unit of the anti-lock braking system. 2.

Installation clearance and damage to wheel speed sensors and ring gears. 3.Whether the gap between the axles of the vehicle is too large.

4.Vehicle sensor failure.