Can mosaic tiles be directly attached to the wall that has been renovated?

I want to install a mirror for my own room, a long dressing mirror, because the frame is not good, so I want to glue the mirror directly to the wall, and then paste the glass mosaic on the side as a frame, I don't know if this is feasible, my home has been renovated, can it be processed directly like this? The mirror is so glued, can it be glued? The last time I looked at the swap space, I saw that I could directly coat the mosaic with something like latex or what kind of glue, and then it could be glued directly to the wall, how did I get it?

Everyone, don't want that kind of sticky answer, the kind of answer that is very standard, explaining what is mosaic, what scraping putty or something, I've searched and seen it all, no, the exchange space you said, I think, either it's the need of the show, it's a temporary disposal method, the tiles are directly pasted on the latex paint, how do you want it? Even if you use the best glue, the wall will fall off. Or what you see is just a mosaic effect of wallpaper, not tiles.

You can buy wallpaper to achieve this effect, or other special decorative materials (such as craft glass, etc.) is a pity, people, but you are not willing to give a point, in the future to ask for others to be sincere, first of all, at least a little sincerity, even if it is to give a point...

The exchange space you are talking about, I think, is either the need of the show, it is a temporary method of disposal, the tiles are directly attached to the latex paint, how do you think it is possible? Even if you use the best glue, the wall will fall off. Or what you see is just a mosaic effect of wallpaper, not tiles.

You can buy wallpaper to achieve this effect, or other special decorative materials (such as craft glass, etc.).

Summary. Dear, I am a mentor know-it-all, I have been serving for many years to answer your questions, I am very happy to have your questions, and the mosaic can not be directly tiled on it.

Dear, I am a mentor know-it-all, I have been serving for many years and I am very happy to prepare for your questions, and you can't directly paste tiles on the mosaic.

The mosaic cannot be directly attached to the tile, and the firmness of the mosaic cannot be guaranteed after paving, so it is still necessary to pave the cement wall. Generally, it is possible to use cement for paving tiles, but it is recommended to use grouts for paving mosaics. Because the density of mosaic is relatively high, the water absorption rate is low, and the adhesive effect of Shuibi mud is not as good as that of grout, and the firmness of Marseille can not be guaranteed after paving.

Before paving the extended materials, use tile adhesive or white cement to plaster a thin layer again, and ensure that the surface of the substrate is flat, and then paste the mesh mosaic on the wall, ground or bright surface. When paving, pay attention to the open space between the mosaic distance and the mosaic particles, and each mosaic according to the direction of the arrow marked on the backing paper to read the file Tong rules neatly paved, and with caulking to wipe firmly. Because mosaic focuses on the use of color, so collage work is necessary to reach a certain plea.

First, there shall be no skewed, warped, hollow drum and other phenomena.

Summary. Dear, hello, I have inquired for you, how to paste tiles on the original mosaic answer; 1. The special glue for ceramic tiles is evenly smeared on the wall, pay attention to the control of the amount, if you use too little, it will often make the mosaic tile paste not firm, too much will often bring inconvenience to the construction, and the tile glue on the wall will be evenly smeared, and the glue thickness will be about two millimeters. 2. After the special glue for the tile is used up, it can be pasted according to the mosaic pattern.

Pay attention to the alignment of tiles, each time a tile is pasted on the wall, you need to pad a thick wooden board on its surface and beat it with a rubber hammer, so as to ensure that it is firmly pasted and avoid falling off later. 3. After completing a part of the mosaic tile, it is necessary to carefully check the pasting situation to ensure that the gap between each tile is consistent and the paste is tight. If the gaps are inconsistent, they can be adjusted with a plastering spatula.

4. After inspection, and when the tile adhesive is dried to a certain extent, you can carry out the joint work. Wipe the caulk in the gap of the mosaic tile, and about 25 minutes after caulking, you need to clean the tile with a damp rag, otherwise it will be difficult to remove the tile adhesive later.

Dear, hello, I have inquired for you, how to paste tiles on the original mosaic answer; 1. The special glue for ceramic tiles is evenly smeared on the wall, pay attention to the control of the amount, if you use too little, it will often make the mosaic tile paste not firm, too much will often bring inconvenience to the construction, and the tile glue on the wall will be evenly smeared, and the glue thickness will be about two millimeters. 2. After the special glue for the tile is used up, it can be pasted according to the mosaic pattern. Pay attention to the alignment of tiles, each time a tile is pasted on the wall, you need to pad a thick wooden board on its surface and beat it with a rubber hammer, so as to ensure that it is firmly pasted and avoid falling off later.

3. After completing a part of the mosaic tile, it is necessary to carefully check the pasting situation to ensure that the gap between each tile is consistent and the paste is tight. If the gaps are inconsistent, they can be adjusted with a plastering spatula. 4. After inspection, and when the tile adhesive is dried to a certain extent, you can carry out the joint work.

Wipe the caulk in the gap of the mosaic tile, and about 25 minutes after caulking, you need to clean the tile with a damp rag, otherwise it will be difficult to remove the tile adhesive later. a4a

Brush the walls with mixed tile glue or white cement. Use a special tool to apply evenly and evenly. The thickness of the cement is preferably about pasting mosaic bricks

According to the design drawings, lay the Masanko tiles on the floor with a good glue on the wall. Every time a tile is laid, it must be firmly bonded with glue. It can be slapped firmly with rivets or evenly with a rubber mace to ensure that each inlay tile is firmly held together.

3. Gap filling work: After the mosaic tile is dry and has a certain strength, the joint filling work can begin. At this point, it is best to use a professional caulking rag or putty shovel to evenly fill the adjusted caulk into the gaps of the mosaic tiles.

Pay attention to the fullness of the caulk when filling. The area of each operation should not be more than 2 square meters to ensure the quality of construction and reduce the difficulty of cleaning. 4. Clean and perfect:

After filling the mosaic tiles for 20-25 minutes, use a damp cloth or damp sponge to wipe off any excess caulk from the surface of the tiles. Take care to control the intensity of the erase type so as not to wipe off the caulk in the gaps. Wipe with a dry cloth to complete the paving process.

Mosaic tiles can be judged trapped in the following 4 steps.

1. First of all, apply the well-proportioned tile adhesive to the wall to ensure uniformity.

2. Secondly, the tiles are laid according to the drawings and then gently beaten with a rubber hammer to ensure the firmness of the bonding.

3. Then use a small ash shovel to mix the ash joints and fill in the fallen tiles.

4. Finally, after the water is drained, pour the grout agent into the brick joint until it is full and does not overflow.

What to pay attention to in tile paving:

1. Soaking. First of all, before the tile is paved, it should be soaked in water, so that it can absorb enough water to congratulate the end, so that when laying in the later stage, the viscosity of the cement can be increased, so that the tile is laid more firmly.

2. Cement. Secondly, when laying ceramic tiles, we should pay attention to the quality of cement, good cement, viscosity and strength are very high, and it is not easy to paste poorly. Therefore, when people choose cement, they must choose the cement in the shelf life.

In addition, the choice of sand is also important, it is better to choose river sand, which has a high moisture content to ensure that the tile is pasted more firmly.

3. Tile cutting and laying. Then, when laying tiles, use tiles of different sizes according to the space used. Some even need to cut tiles, but be careful to cut them flat and of a consistent size.

Otherwise, it will affect the aesthetics of the home. In addition, when laying tiles, the position of the first brick is particularly important, it is the baseline of all the tiles in the later stage, if the position is skewed, the later tiles will also be skewed.

4. The wall is pressed to the ground. Finally, when laying tiles, you can choose the laying method of wall pressing the floor, so that the water droplets can flow down to the floor tiles, avoid water storage on the wall, and facilitate cleaning.