How to break the hard disk of the notebook and can t detect it

This can be checked in the boot item in BIOS mode on the computer.

Let's take an ASUS laptop as an example, and the steps are as follows:

1. Click the power button of the ASUS notebook, and the computer motherboard icon appears on the screen, and immediately press the F2 button to enter the BIOS interface, as shown below.

2. Enter the BIOS interface and select the BIOS Version:30S option, as shown in the figure below.

3. Look at the bottom from left to right column 3 "boot menu(f8)", and click on it rudely, as shown in the following picture.

4. Check whether the computer hard disk is read by Yanyou shouting in this interface, if the hard disk is damaged, the computer will not be read, the red box in the following figure shows that the hard disk is read, that is, the hard disk is not damaged, as shown in the figure below.

The possible causes are as follows.

1. The system cannot recognize the hard disk. Most of these faults occur on the connection cable or IDE port, and the possibility of the failure of the hard disk itself is not very likely, so you can quickly find out where the fault is by reinserting the hard disk cable or replacing the IDE port and cable.

2. CMOS failure. When the hard drive type is wrong, sometimes the system simply fails to boot, and sometimes it does, but read and write errors occur. For example, if the disk type in CMOS is less than the actual disk capacity, the sectors behind the hard disk will not be able to read and write, and if it is multi-partitioned, individual partitions will be lost.

3. Startup failure caused by partition table error. Partition table error is a serious error of the hard disk, and different error degrees can cause different losses. If there is no active partition flag, then the computer fails to boot.

However, after booting the system from a floppy drive or optical drive, the hard disk can be read and written, and the active partition can be reset by fdisk for repair.

It is possible that there is a problem with the hard disk, and the system has an error when it self-checks the hard disk, and it is frozen.

You can not connect this hard disk first, use the original mechanical hard disk to boot the system to the desktop, and then connect to this solid state drive, see if it can be recognized normally, can partition and format, and you can also use hard disk detection software to detect whether there is a problem with the hard disk.

If it can be recognized normally in the Windows environment, can be used normally after formatting, and the problem cannot be detected, it should be fine. If it can't be passed, it means that it is bad, and the return should be hurried. Of course, it may also be a problem with the motherboard's interface and cables, although it is less likely, it should also be ruled out.

Summary. Hello dear! Here are some ways to check if your laptop hard drive is broken:

1.Error message on startup: If you encounter an error message when starting up your laptop, such as "Unable to read hard drive", or if the system cannot boot from the hard drive, this could be a sign that the hard drive is corrupted.

2.Hard drive hanging: When the hard drive is not functioning properly, there may be a "hard drive hanging" situation, which means that the hard drive cannot access the data.

If you hear a monotonous noise or "click", it may be a damaged hard drive. 3.Slow access to files or inability to access files:

If you notice that accessing files becomes slow, or if some files are inaccessible, there may be a problem with your hard drive. 4.Abnormal noise:

If the drive is working normally, there is a sudden and unusual noise, such as a harsh magnetic noise, this could be a sign of damage to the drive. 5.Bad sectors:

Bad sectors on your hard drive can lead to data loss and corruption and can be scanned in Windows Disk Utility.

Hello dear! Here are some ways to check if your laptop hard drive is broken:1

Error message on startup: If you encounter an error message when starting up your laptop, such as "Unable to read hard drive", or if the system cannot boot from the hard drive, this could be a sign that the hard drive is corrupted. 2.

Hard drive hanging: When the hard drive is not functioning properly, there may be a "hard drive hanging" situation, which means that the hard drive cannot access the data and secrets. If you hear a monotonous noise or "click" sound, it means that the hard drive of Laling may be damaged.

3.Slow or inaccessible files: If you notice that accessing files is slow, or if some files are inaccessible, there may be a problem with your hard drive.

4.Abnormal noise: If the hard drive is working normally, there is a sudden abnormal noise, such as a harsh magnetic noise, this could be a sign of damage to the hard drive.

5.Bad sectors: Bad sectors on the hard drive can lead to data loss and corruption which can be scanned in Windows Disk Utility.

Dear relatives, a hard disk is a type of device in a computer, also known as a hard drive or disk drive. The hard disk is one of the main devices for storing computer data, which reads and writes data on the platter through magnetic materials. A hard disk is usually composed of multiple platters, read/write arms, motors, controllers, and other components.

The data is stored on the surface of the platter, and the read/write arm is responsible for moving and reading and writing on the platter. Hard drives can be divided into two categories: mechanical hard drives and solid state drives. HDDs use mechanical motion to read and write data, while SSDs use flash memory to read and write data, so they are faster and more stable than HDDs.

Hello, I found that the hard disk of the notebook is broken, and there are several ways to answer the hidden:1Error message at startup:

If your laptop starts up with a hard drive-related error message, such as "Hard drive not found", "Hard drive cannot be read", etc., then it is likely that the hard drive is broken. 2.An error occurred while accessing the file:

If you make an error when accessing a file on your hard drive, such as "file corrupted", "inaccessible", etc., then it is also possible that the hard drive is broken. 3.Slow access:

If your laptop hard drive has become very slow to access, such as longer boot times, slower file opening times, etc., then it is also possible that the hard drive is broken. 4.Abnormal sound:

If your laptop hard drive is making unusual noises, such as "clicking", "hissing", etc., then it is also possible that the hard drive is broken. If you find any of the above problems, it is recommended to back up your data immediately and contact a professional maintenance personnel for repair or replacement of the hard drive. In addition to this, there are some other situations that can also cause similar problems in the notebook, such as operating system failure, virus infection, etc., so it is recommended to take troubleshooting steps before determining that the hard drive is broken to ensure the accuracy of the problem.

In short, if you find that your laptop has a problem with the hard drive, you must deal with it in time to avoid data loss or affect your use.

Laptops will inevitably have various situations under our long-term use, for example, some netizens recently reported that they have encountered a situation where the laptop cannot detect the hard disk, and they don't know what is going on, and they don't know how to deal with it, so what we will share for you today is the solution to the computer suddenly not detecting the hard disk.

Here's how to fix it:

a) Hard disk connection problems.

If the computer does not recognize the hard disk, the first thing to consider is whether the hard disk cable has been connected.

In order to avoid loosening of the data cable and power cable, replug the power cable and data cable.

b) BOIS settings.

1. Open the BIOS, check the StandardCMOSFEAURES page, check whether the hard disk is set to none, and set this to Auto.

2. Next, find the ATA (SATA) option and select Enter.

4. If the computer is using SATA hard disk, and the SATA interface is turned off, the computer will not be able to find the hard disk.

5. If there is an AHCI option in the computer, generally select it.

c) Use Disk Management.

1. Open the computer management window and click the Disk Management option.

2. Sometimes the computer can't recognize the hard disk, but you can still see the hard disk in the management interface.

3. In the disk management window, you can change the number and path of the drive and format the hard disk.

4. You can also set the main partition as the active partition.

c) Use disk partitioning software.

1. I take partitionmanager software as an example, in the partition menu, there are various functions such as formatting partitions, deleting partitions, adjusting partitions, assigning drive letters, setting active partitions, etc.

2. Click the change menu to reload the disk information.

3. Click the disk menu to reload the master boot record.

4. You can also use software to repair the damaged hard disk, so that the computer can re-recognize the hard disk.

The solution to the sudden failure of the computer to detect the hard disk is shared here, and if you encounter the same situation, you can follow the above methods to deal with it.

When the notebook can't detect the hard drive, you can try the following methods to solve it:

1.Check the hard drive connection: First, make sure that the hard drive is properly connected to the laptop.

A poor hard drive connection can cause the computer to not detect the hard drive. You can turn on your computer and check if the hard drive cable is loose or damaged. If needed, replace it with a new hard drive cable.

2.Check the hard drive jumper: Incorrect hard drive jumper settings may cause the computer to not recognize the hard drive. You can refer to the manual of the hard disk or the tutorial on the Internet to set the hard disk jumper to the correct master-slave jumper.

3.Enter the BIOS settings: After moving the computer slowly, press the DEL, F2, F10, etc. (the specific keys vary depending on the brand and model of the computer) to enter the BIOS settings.

In the BIOS, check if the drive is correctly recognized. If the drive is not recognized, you can try changing the drive mode to IDE or AHCI. Save the BIOS settings and restart your computer.

4.Use the MHDD tool to detect the hard drive: If you suspect a hardware issue with the hard drive, you can use the MHDD tool to detect it.

5.Replace the hard drive: If none of the above methods can solve the problem, you can try replacing the hard drive. Replace the original hard drive with a new one, and then reinstall the operating system.

6.Seek professional help: If you can't solve the problem, you can contact your computer manufacturer or professional repairer for testing and repair.