There is a problem with booting, how to solve the boot problem

Updated on number 2024-02-09
11 answers
  1. Anonymous users2024-02-05

    Memory instructions can not be read, this is a problem that often occurs in the use of the computer, the cause is very complex, it will be difficult to eliminate for a while and a half, but it doesn't matter, press OK, cancel, restart, you can. Interested netizens can try to solve the problem with the following methods:

    1.If the memory module is broken, replace the memory module.

    2.Dual memory is not compatible, using the same brand of memory or only one memory.

    3.If there is a memory quality problem, replace the memory module.

    4.Heat dissipation issues to enhance heat dissipation inside the case.

    5.If the memory and motherboard are not plugged in properly or the hardware is not compatible, reinsert the memory or change the socket.

    6.If there is a problem with the hard drive, replace the hard drive.

    7.If it is a new system, you should install the motherboard driver first.

    8.Software is corrupted, reinstall the software.

    9.Software bugs, patch or update to the latest version.

    10 If the software is not compatible with the system, patch the software or try the compatibility mode of the system.

    11 There is a conflict between the software and the software, if you have recently installed any new software, try uninstalling it.

    13 Virus Problems Antivirus .

    14 Antivirus software conflicts with the system or software Since the antivirus software enters the underlying monitoring system, it may conflict with some software, try uninstalling it.

    15 There is a problem with the system itself Sometimes the operating system itself will have bugs, so pay attention to installing the official release update, like the SP patch, it is best to put it on. If that doesn't work, reinstall the system, or replace it with a different version of the system.

    16. Try the command to solve the problem that the memory cannot be read-only, open the cmd window and enter the following command:

    for %i in (%windir%\system32\*.dll) do s %i carriage return;

    for %i in (%windir%\system32\*.ocx) do s %i carriage return. Restart your computer and you're good to go.

  2. Anonymous users2024-02-04

    It is recommended that you reinstall the system.

  3. Anonymous users2024-02-03

    I seem to be similar to you, except that the computer has been on standby for a long time, and some programs are like this, but it doesn't matter.

  4. Anonymous users2024-02-02

    Summary. Press the win+r key combination on the keyboard at the same time to bring up the running window;

    Enter msconfig and click the OK button.

    In the General tab, click Select Selective Startup, unload the startup items, and select Load System Services;

    Click on the Services tab;

    In the Services tab, check Hide all Microsoft;

    Then click Disable All;

    Then click on the Startup tab to open the Task Manager;

    Disable all startup items, and then restart your computer.

    How to solve the boot problem.

    Press the win+r key combination on the keyboard at the same time to bring up the running window; 2.Enter msconfig and click the OK button. 3.In the General tab, click Select Selective Startup, unload the startup items, and select Load System Services; 4.

    Click on the Services tab; 5.In the Services tab, check Hide all Microsoft; 6.Then click Disable All; 7.

    Then click on the Startup tab to open the Task Manager; 8.Disable all startup items, and then restart your computer.

    The first part is not open.

    You hurry up and go to the Science and Technology Plaza to find the place where you bought your computer.

  5. Anonymous users2024-02-01

    Hello:——1,One of the reasons: the data cable of the hard disk, or the power cable is not in good contact or falls off, and the operating system cannot be recognized.

    The operating system is corrupted and the computer cannot enter the operating system. So the main interface of the BIOS will appear.

    Practical arguments: In a normal computer, unplug the data cable or power cable of the hard disk, and this screen will appear.

    CheckIs the hard drive's data cable or power cable well connected? Is the system damaged? Countermeasures should be taken according to the situation.

  6. Anonymous users2024-01-31

    To turn on the machine, press del or F1, F2 (the setting is different for each manufacturer).

    will enter this BIOS mode.

    Reboot, or press F10, press Enter. Can.

  7. Anonymous users2024-01-30

    How do you press the starter? Leave it alone when you turn it on, he'll start it himself!

  8. Anonymous users2024-01-29

    This is the BIOS setup interface, just press ESC to exit normal boot.

  9. Anonymous users2024-01-28

    Enter this interface when you turn it on, maybe the F2 button or the del button is broken.

  10. Anonymous users2024-01-27

    Try to run"c/windows/system32/,nvstartup"Accidents happen.

    This is the startup item of the nvidia graphics driver, which can be uninstalled and reinstalled. Or remove the items found in the startup items. To do this, start, run, type msconfig, find startup, and then remove the tick in front of the bumper item and press Apply.

    2) Close the startup item of the faulty graphics card.

    Startups can be turned off (autostartups can be found in several of the following ways).

    2. Click"Get started"Run Enter after entering msconfig and click Enter"Launch"Look for the option of the boot prompt inside, remove the previous tick after finding it, and press OK to apply. After restarting the computer, a dialog box will appear when you boot up to the desktop, add a checkmark to the dialog box, and you can confirm it.

    3. Remove the auto-start item.

    Start running the input regedit back to open the registry and be sleepy in the morning.

    hkey local machine software microsoft windows currentversion run] on the right, hkey current user software microsoft windows currentversion run] on the right, see if there is an option you are looking for, if there is a deletion, restart the computer.

  11. Anonymous users2024-01-26

    DLL files can be searched on the Internet, and a lot of them can be searched.

Related questions
5 answers2024-02-09

After all, Vista is not very stable, and it is very demanding, and I think the following two are good. >>>More

6 answers2024-02-09

Enter safe mode and open the hkey in the registry

Local Machine Software\Microsoft\Windows\CurrentVersion\Run\Restart after deleting the HBKRNL entries in it. >>>More

22 answers2024-02-09

Set up x yuan. For every price increase, 10 pieces are sold less. >>>More

6 answers2024-02-09

Specifics??

The fan doesn't turn because your power supply is not plugged in. >>>More

16 answers2024-02-09

I can only say that you are not very firm about your current boyfriend! >>>More