Hurry!! My solar pipe is cracked and is a small opening, resulting in water seepage, what should I d

Is it now past the deadline for after-sales?

Then drain the water in the water tank, fill the caulk with waterproof glue and then apply glass glue. It works well.

I think it's more convenient to change it, if you use caulk, you will have to do it again after a while, how troublesome it is, not to mention that it's been a year, it's almost the same to change it, anyway, solar energy is not so expensive.

What hoses do you use? There are many pipes that cannot be used outdoors, can not withstand the ultraviolet radiation of the sun, your water pipe performance indicates that it has been aged, don't do useless work, replace it quickly.

Glue for pipe water seepage is not good, isn't it more troublesome for you to cut off the copper parts every time, the copper parts are not cheap, quickly replace the pipes, there is no worry, more than 30 meters of pipes are enough, the cost is not high.

Or is it recommended that you replace all the tubes! If it is not a long-term solution, think about it, you will have to live in the house for decades, if it is broken, it will take time and effort to make up!

Dear, hello, I am happy to serve you, the answer to the following solar overflow non-stop leakage is caused by the water is not closed in time, according to the different control methods, the main reasons are: 1. Automatic control type of solar energy: water level sensor damage (common), water solenoid valve damage (possible), controller failure (rare), etc.

2. Ordinary mechanically controlled solar energy: damage to the float ball valve (common), damage to the manual water valve (possibly). If the meter is not displayed when the water leaks is not faulty, the probe is not faulty, and the probe is replaced; If the power supply of the instrument is unplugged and the water leaks, it may be a solenoid valve failure, replace the solenoid valve; If there is a parallel backup valve installed next to the solenoid valve when Nai Mingling is installed, this backup valve is generally closed, if it is opened, the water tank must be closed manually, otherwise the overflow port will always leak.

You can also find after-sales, if it is inconvenient to go up and unscrew the screw of the overflow port (put the hot water first), the leather cushion inside should be loose, just press the screws on the line, if it leaks again, the silicone rubber ring connected to the solar overflow pipe and Neidan is broken.

The methods for repairing the rupture and leakage of solar water pipes are: 1. Replace the pipe, 2. Direct connection, 3. Hot welding.

1. Replace the tube.

Replacing the tube is a straightforward way to replace the entire tube. Or cut off the broken section and replace it with a new section of pipe, which is connected with a joint.

2. Direct connection.

Trim and cut the fracture together, do some processing, and connect it with a pipe tool. But Ye Li can use nuts, open sleeves, and rubber sleeves, and the specific operation is flexible, and pay attention to the direction of each part.

3. Hot welding.

Another way is to hot welding, through hot welding, the fracture is connected again.

Precautions for the use of solar water heaters:

1. When the solar water heater is in use, if there is sewage in the water tank, it cannot be replenished immediately. Because when the vacuum tube is air-dried, it will cause the temperature of the surface to rise to about 2500 degrees, and once water is added, it is easy for Shansong to blow up the tube. The best time is half an hour after sunset to add water.

2. If the water heater is installed with an auxiliary heat source, it is necessary to carry out regular inspection work to see if it can be used normally. And to ensure that the leakage protection device can be used normally, it can be plugged in and turned on. In addition, when heating the auxiliary power supply, it is necessary to pay attention to the water in the water tank not to tease the spine Zheng Zheng less than 50%.

3. Solar water heaters are generally installed outside, and in order to ensure their use, they need to be fixed firmly, so as to ensure normal use in the later stage and reduce potential safety hazards. Moreover, in a windy environment, the water heater's tank needs to be filled with water to increase its weight.

Leakage from the water outlet of the solar water heater tank is caused by the following 2 points:

1. Water leakage at the junction between the outlet of the water tank and the pipe fittings.

2. The junction between the outlet pipe of the water tank and the box body.

Maintenance method: Please close the water heater inlet valve, and then check the leaking part. If there is a leakage at the junction between the outlet pipe mouth of the water tank and the pipe fittings, use a wrench to re-tighten the original outlet pipe joint to solve the problem; If there is a leak at the junction between the outlet pipe of the water tank and the box, it means that the silicone ring built into the outlet of the water tank is broken and the soft hose needs to be replaced. First buy a silicone ring of the same specification (available in solar accessories stores), then pull out the outlet pipe, then take out the old silicone ring, then put the new silicone ring in the water heater tank out of the water hole, and finally wipe the outlet pipe clean, wipe a little meal wash as a lubricant, and rotate to insert the steel pipe.

What should I do if the water is blocked at the lower mouth of the water heater? If the solar water heater eliminates the water, then it is a very troublesome thing, so if the water is blocked, then it may be that there is more water in it, so the perfume is blocked, this phenomenon is very difficult to deal with.

Close the water pipe valve in the room to stop the water ingress. Remove the connector where the water is leaking and replace it if it is broken. Check that the head of the sewer pipe is flat, you need to level it out.

If there is a water leak between the pipe fittings, it is necessary to disassemble the pipe fittings and wrap the raw material belt around the threaded position. If you use a PVC pipe, you need to cut out the leaking part and install the new PVC pipe with glue.

You can do it in the way you want first, and then if you don't understand, you can learn it at the time.

The accessories store buys a cold water valve that matches the inlet pipe joint of the electric water heater. Turn off the main valve of the tap water, unscrew the hose fitting, replace the valve you just bought and check that the joint is not leaking.

The box of the water heater is made of metal and steel, and the wall of the water heater is thinned due to the corrosion of water pressure, hot and cold water and scale for a long time, resulting in water leakage. On the contrary, in a short period of time, if the water pressure is reduced and the impurities in the water are reduced, the leakage point can be plugged without water leakage. It could be the cause of the clogged exhaust hole, it could be the reason why the tank was suctioned, probably.

It may be that there is still water in the pipe, the dynamic temperature is too low, the water is easy to freeze, and the water pipe is swollen and cracked. In winter, solar water heaters are not used.

It is best to drain the water inside, because in freezing weather, if the temperature is lower in winter, the flat plate system should drain the water from the collector; If the forced circulation system with the function of antifreeze control system is installed, it is only necessary to start the antifreeze system, and there is no need to drain the water of the system.

Expansion of the stove exhibition information: how to clean and maintain the water heater:

Gas water heaters.

For external cleaning, you can often wipe it with a wet towel, and pay attention to not using a series of cleaning agents such as acidic and alkaline to wipe the water heater;

The burner part of a gas water heater needs to be removed on a regular basis.

Put the parts with carbon deposits into the cleaning solution with carbon remover, soak them until the carbon deposits soften, then wipe them clean with a brush or old cloth, and finally rinse them with hot water and dry them.

The decarbonizer cannot be used to clean the carbon deposits on the heat exchanger, so as not to damage the heat absorption and heat reflection coating layer on the heat exchanger, and the heat exchanger can be wiped with a rag;

It is necessary to frequently check whether the gas supply pipeline (rubber hose) is in good condition, whether there is aging, cracks, leakage and other phenomena, and deal with it in time when it is found that there is any bad phenomenon.

Hello dear, I am glad to answer for you what the root leakage of the solar outlet is.

First, the water tank leakage in fact, the water tank leakage is relatively rare, if the inspection is found to be the tank leakage, then quietly need to replace the new solar water tank. It is also possible that the water tank is not installed properly, resulting in the solar water heater leaking and starting the car, which only needs to be reinstalled. Second, the solar valve leakage valve leakage is mainly due to the failure of the valve, which needs to be replaced with a new solar valve or solenoid valve.

3. If the water pipe leaks if the upper or lower water pipe is leaking, it is generally due to the aging of the long use time, and it is necessary to replace the new solar water heating pipe. Fourth, the leakage of the solar exhaust port is usually due to the damage of the sensor or the damage of the meter, so it is necessary to replace the water temperature level meter or solar meter. 5. If the solar heating tube leaks water and the heating position leaks, then the electric heating is rusty and damaged, and a new sealing ring or electric heating rod needs to be replaced.

6. Leakage at the solar vacuum tube The leakage at the vacuum tube is basically because the solar silicone ring is aging, and the old vacuum tube needs to be replaced with a new silicone ring. 7. Water leakage at the solar interface This interface mainly refers to the interface between the upper and lower water pipes and the water tank, if the interface pipeline is not tightly connected, the pipe fittings are damaged and the faucet is loose, which will also lead to water leakage in the water heater. 8. Cracking and leakage of the inner tank weld If the inner tank weld of the solar water heater is cracked, it will also lead to water leakage.

Just replace the water tank or solder the open soldering area.

There are two reasons for a burst pipe:

During the day, the sun is good, the temperature of the collector tube is high, and the water is suddenly on, the cooling is too fast, and the thermal stress generated is higher than the strength of the collector tube glass, and the pipe bursts occur.

When the sun is good, the heat collection effect is significant, it is easy to boil the water, and the steam produced is hindered by the scale accumulation, and can not be discharged smoothly, and the temperature rise continues, which will cause local high pressure and burst pipe.

Water heaters should be cleaned and descaled regularly.

If you don't want to go to the roof, you can buy a set of solar water heater without removing the scaler, you can use it to inject descaling agent into the water heater indoors, the operation is simple and convenient, and it can be cleaned regularly after using it, when this problem can be avoided again.

Because the temperature difference is too large, the glass has its own expansion coefficient, when the outside temperature exceeds his bearing capacity, it will break, in the solar energy industry called the fry, a more common problem, you ask the seller of solar energy, they all know, generally will give you free replacement, even if it is not free, it will be cheaper than usual to buy, in the final analysis, it is a product quality problem.

Replace the new pipe, and add thermal insulation film to the outdoor pipe in winter to prevent freezing and cracking.