How to use Xiaomi 1S as a computer camera head

This file needs to be installed for both ports.

1. Unzip the computer client file and run the file. It is recommended to install it on the default C drive without changing the path.

OK, the computer has been done, let's get the phone again.

The description is written casually, such as "Ximen's **", and the IP is filled in with the IP address of the local computer. (Get native ip: start - run -cmd - type ipconfig etc method).

Fourth, if you can already connect, turn off the "stop and disconnect" of droidcam on the mobile phone, turn off the "language**" on the computer, and click on the other party directly**. It's connected.,You're still the green robot here.,Then click on the description on the phone just "Ximen's **", and you're done!

Of course, the first, second and third steps only need to be installed and debugged for the first time, and every time you and others in the future, you can start directly from the fourth step. As long as the connection is successful, there must be a small green robot in the lower right corner of the computer, otherwise it will not be connected to the computer.

Hi! A more detailed description of the problem will help netizens understand the troubles you are encountering and help you solve the problem more accurately. Thank you for supporting Xiaomi phones!

This requires a computer to control the phone, can you try sunflowers?

Method steps.

1.First of all, install the PC side glow on the computer and turn it on.

2.Then install the glow phone on your phone and open it.

3.Now you can see it on your computer, and the camera on your phone captures the footage.

4.If you can't connect, you can enter the verification code on your phone on the computer interface.

The main cameras of the Mi 1S and Mi 2 are the same except for the different apertures, and the Mi 1S uses a back-illuminated second-generation image sensor, which greatly improves the shooting effect.

The front and rear cameras of the Xiaomi 1S use back-illuminated image sensors. Back-illuminated CMOS is a type of CMOS technology in which a conventional CMOS sensor is located behind a circuit transistor, and the amount of light entering is affected by occlusion. The so-called back-illuminated CMOS is to turn it in the opposite direction so that the light enters the photosensitive diode first, thereby increasing the amount of light sensitive, and significantly improving the shooting effect in low-light conditions.

FYI.

The camera parameters of the Mi 1S and Mi 2 are similar except for the aperture, and they are both back-illuminated CMOS

The Xiaomi Mi Phone 1S is equipped with the world's fastest dual-core processor, a new 2 million pixel front camera, an F large aperture and a 28mm ultra-wide angle 8 million pixel back-illuminated rear camera, which has the same photo performance as the Xiaomi Mi Phone 2. The 4-inch screen with transflectographic technology makes it possible to see the content of the screen even in strong sunlight. More than 10 hardware improvements, the classic model is perfectly rebuilt!

The M1S just adds a front camera on top of the M1.

The wider the aperture, the more you can photograph.

It should be different, and you need to read the instruction manual in detail.

It's not much worse, I don't need it anyway.

1.First of all, on the computer.

Install it on the PC.

Glow good and open.

2.Then install the glow phone on your phone and open it. Inside 3Now you can see it on your computer, and the camera on your phone has captured the picture.

4.If you can't connect, enter the mobile phone on the computer interface to verify.

Hi! 1.Please open the Settings All Settings app Camera to clear the data and try to restore it.

b.During this time, please back up your data first, enter recovery (shut down, press and hold the volume + power button to enter recovery) to clear the cache, clear user data, clear all data,. The computer is equipped with a driver,Let's talk about a miflash flash tool,This is the driver link:

m 1. m2 cWhen everything is ready, please follow the brushing tutorial on the official website to use the sixth line with the old grip brush, which is the official flashing tutorial: