The plastic steel window glass is 2 05 meters long and 50 cm high

The window is high in meters, the left and right meters wide, and you want to make 2 pieces of glass in the place of meters * meters, and you can also make a good point (make a cross brace in the middle). There is no basis for saying that the glass is stressed at both ends, mainly because you have good glass above it and push the door must be cross-bracked (firm), and the insulating glass must be cross-braced. The glass in the middle is generally left and right (4mm when speaking) is normal.

If you don't feel tempered, you can look at the glass corner (there is one on each tempered glass), or if you don't have it, it's fake, and you can look at it yourself.

The rails are the slides above and below the doors and windows.

Making 1 piece is similar to 2 pieces, one is more beautiful in terms of aesthetics, you can make 5 + 5 double tempered laminated glass, so that if there is any accident, the glass will not fall off, which belongs to safety glass. 、

If you want to do a push-pull type, you can install a rail. It's not only safe, but also beautiful.

This is not difficult, isn't it, you do it directly, add a brace in the middle of the long direction, and divide it into two parts, isn't it safe and easy to care for, in fact, you can do it directly You use double-layer tempered glass is more durable One square meter is between 230 yuan and 260 yuan.

The plastic is not strong, but it is okay to add steel inside, and it is best to add a mullion in the middle, which is firm and beautiful.

I can change it. Here's how:

1. Remove the broken glass first.

Process: Use a greasy knife or a thin blade to remove the strip first (first remove the long strip, insert the greasy knife in the middle of the strip and the window frame, and select the position in the middle part, here it is good to pry, pry out the gap, and then carefully disassemble the two ends, be careful not to hurt the strip), remove the two long strips, and then disassemble the two short ones, and finally take down the double glazing, clean up the debris, pay attention not to hurt the contact surface of the sealing strip sandwiched in the middle, and insert it smoothly with a greasy knife to cut it.

2. Replace the glass.

Measure the size and thickness, and buy a piece of glass of the right size and a bucket of glass glue. Wipe the new glass clean. Clean the contact surface of the sealing strip, put the glass, confirm that there is no debris and dust inside, and seal it with glass glue (be sure to seal it to avoid air leakage.)

After installation, the bead can cover the glue, so you don't have to worry about the appearance).

3. Replace the glass.

After the glue is dry, the double-glazed glass is put back, contrary to the time of dismantling, first install a short strip, and then install a long strip. Polishing the glass and finishing.

There is a strip on the inside of the window, which is driven into it with a rubber hammer when installed, remove it, take down the broken glass, cut two pieces of glass according to the original size (referring to a double layer, cut one piece in a single layer) and clamp the rubber strip to form a cavity, and then install it.

Don't count the strip only measure the actual distance between the height and width of the window frame and the window frame, the height is removed by 2mm and the width is removed by 5mm to cut the actual size of the glass. Complete! For this problem, I removed my window and measured it for half an hour!! Hey--- no problem next time.

Hello! This is the standard calculation method: do not count the strip only measure the actual distance between the height and width of the window frame and the window frame, the height to remove 2mm and the width to remove 5mm is to cut the actual size of the glass.

...Is it a size or a ** or what?

The window sash itself has a "front and back", which refers to the cut on the window sash, while the glass has no front and back.

There is no positive and negative distinction between glass, and there is positive and negative distinction between plastic steel windows.

Nope.

It depends on whether you choose regular glass or tempered glass.

There is no positive or negative.

Listen to me: that's what I do.

The insulating glass is double-layer glass, which is filled with gas between the two layers of glass, generally air, and then the circumference is sealed with an aluminum frame containing desiccant (molecular sieve) and PU glue. The sound and heat insulation effect is super good! The windows of my office are insulating glass, and when they are closed, the sound outside is basically inaudible and quiet.

Don't be greedy and cheap to listen to the decoration company, simply add another layer of glass and you're done. Why do we make insulating glass with an aluminum frame of molecular sieve, the purpose is to get out the water in the middle layer. If you simply add a layer of glass and don't seal it to remove water, the weather changes, especially in winter, you will find that the glass is shrouded in water mist, you can't see anything, and the thermal insulation effect is not good.

Double-layer glass is divided into insulating glass and vacuum glass, vacuum glass is higher than insulating glass in terms of sound insulation and thermal insulation effect, but it is also high, if the noise is not extraordinarily large with insulating glass is enough, in addition, check the perimeter of the window and the sealing of the adhesive strip.

Yes, although it can't all be screened, but the effect is at least twice as much, my home is under the channel, and the plane is about to land below the flight altitude of 1000 meters, the sound is basically negligible, of course, the product is good.

It also costs a lot of money to replace it with a double layer, so it is better to add a layer of windows outside.

A little better, but not thoroughly.

If you want to solve the problem thoroughly, you may wish to use double-layer vacuum glass.

The Moon Celestial Stone is good, it is not a reference, but it has to be chosen if you want to do it. Only vacuum sound insulation is good, and the price difference with the double layer is not very far.

It's not the same thing!! Hollow refers to the one that is made at the time of production, with a layer of air in the middle; The double layer means that after the glass is made, the two pieces of glass are installed separately.

There is a pressing strip on the side of the plastic steel window frame, which is the black strip mentioned in the upper two places, you can use a screwdriver flat mouth to start from the window foot from the window foot, as long as you warp one other, it is easy to get.

The glass can be removed by warping the small plastic steel strip with black strips. Pry carefully with the glass slowly.

Upstairs said yes, but the general glass and the frame are glued with super glue, and I figured it out.

First disassemble the white strip around the plastic steel, use a screwdriver, first remove the order of up and down or left and right, or you can directly find the door and window manufacturer to let them help you change. I am a door and window manufacturer in Beijing, and you can contact me if you have one in Beijing.

You can't fix it, you have to find a place to process plastic steel doors and windows, and make hollow heat-sealing glass.

If it is a push-pull fan, you should first remove the fan, use a flathead screwdriver or a flat spatula to lift the plastic steel strip pressed with glass, measure the size of the inner mouth with a tape measure, and remember to leave the gap. Draw another piece of glass and put it in, then knock the strip on it, and reattach the fan to it.

If you fix the glass, you can directly take out the bead and change the glass.

By the way: stay safe.

Yikuang Street innovates doors and windows, and his home uses butyl rubber double-channel sealing process to make insulating glass, which has the advantages of long service life and impermeability.

You can change it with a small window length. About 100 yuan per square meter, the left dust bucket and the right double glass.

There is no vacuum, and the vacuum breaks the pin wheel and does not jump off.

It is the kind of hollow aluminum strip butyl glue that is very good.