Sony LT26i has been using it normally after flashing the new bee rom, and suddenly one day the wifi

Some of the third-party ones are a bit buggy. It's not the original factory's good. Stable.

Brush back to the official once first. After flashing a third-party rom. This kind of problem can be solved in this way.

System Problem: You try to enter recovery mode with double w try.

This is the problem you brushed out.,You can save it if you need it.,It's good in a few minutes.,If you want to help, you can directly + account consultation.,You can definitely save it!!

Look for the ROM home on the Internet, and look for the ROM package in zip format. Swipe with a card. It's safe. There are a lot of online card search and swiping tutorials.

Router problem.

I've met it too.

Your router may be just as it says on the internet. To crack that kind.

That's what I use. I was looking for a telecom worker to help me get it done.

I found on the know that you asked the wifi has been in the WLAN state all the time, did you finally solve it? I'm having this issue too.

Later, it turned out that the mobile phone motherboard or wifi module was broken, and yours must have been too.

What is your current system version? If you have been following the official system updates, it is not recommended to flash your computer.

And when you mention the WLAN key, you are referring to **. I think I've only seen it on PSP.

Well, a lot of people have this situation in this machine.,Brush down the system and solve it.,Hurry up and do it for a few minutes.。

If you have flashed the machine, it may be a problem with the ROM or a problem with the kernel, reflash a ROM or try the kernel.

Reboot and then try to connect

You can install a 91 desktop on your phone with the 91 assistant and use it first! lt26 is not unlocked before there is no card swiping this statement!

If it is useless to install the 91 desktop, it is necessary to flash the machine and restore it 1, if the machine is not unlocked, you can use the official upgrade program to restore the specific method is the computer**Sony update service, and then update, the phone is connected to the computer, select the correct model, wait for the phone to update, and the restart is completed.

2、If you have unlocked the BL lock, you can only use flashtool to recover it,LT26 flashtool tutorials are a lot on the Internet,You can search for it!!

At present, you can only find a suitable brush machine package brush machine,Just like the people upstairs said line brush,The premise is to drive the mobile phone first,Don't drive the machine is not flashed,Go to the forum to find it,It's very simple,

Well, in this case, you can only rewrite the system, and it's pretty simple, depending on whether you can do it.

Can I enter the flash mode??? If you can go in, I recommend you use a line brush!! No, just use the card.

This one is very simple, just brush the machine. Where are you ??

My LT26II is too... May I ask the landlord that your problem has been solved??? Seek help!!!

If there is a problem with the network settings, it is recommended to restore the default settings of the phone according to the manual (make a **backup before)

My phone is also this problem, the model is the same, the system is the same·· My problem has been solved...

1. Turn on the wifi, 2. Click the name of the wifi access point you need to connect to.

3. After entering the password, hide the input method and you will find "Show password" and "Show advanced options".

4. Check - Show advanced options.

5. Pull down and "IP Settings" will appear.

6. Change the DHCP in the option to --static.

7. After changing to static, there will continue to be several items below, and the way to fill in is as follows:

IP address: The IP address of your mobile phone can generally be between 1-255, and cannot be set to the same IP address as any device under the route). It is important to emphasize here that the default IP address is displayed, but it is grayed out, even if it is the same as the one you want to set, you need to re-enter it yourself.

Network prefix length: Modify the network prefix length to be the same as the default.

Domain name 2: The same as domain name 1 is fine.

Note: In fact, you have to enter each item yourself, otherwise, the connect button will be grayed out and cannot be clicked.

Hope it helps...