How many kilometers is a good run in? Do you need to pull the high speed? Is cruising bad for runnin

In fact, the run-in period is 2000km.

You are an automatic car there is nothing to control As long as the throttle speed does not exceed 3000 rpm during this period, manual In fact, each gear needs to be run in for a period of time, not more than 3000 rpm, and 7500km after you can pull the high speed, driving the best cruise, so that the engine is more even, after running for a period of time, you can pull the fastest to let the engine stretch the maximum capacity and can also remove carbon deposits, so that when you are at low speed, it is more relaxed, and it is more fuel-efficient. Is my satisfaction not?

Ha ha!!

Cruise control is fine.

Don't pull it up. When I pull it, I affect the engine of the car later.

It usually seems to be 100,000 kilometers.

I remember watching the show 5 years ago.

I forgot how many tens of thousands.

Excuse me.

The fixed speed is better. Probably around 2000-3000.

Avoid driving at high speeds, and it is generally better to keep it below 90.

In addition, the speed of the manual vehicle running-in period is best within 2500.

Sega run-in 2000 km.

There is no need to pull the high speed.

Cruising will not have a bad effect on the run-in process, on the contrary, it is better.

After 2000km, it can be properly pulled at high speed to remove carbon deposits.

After 6000km, you can pull down the limit and it is good for the power of the car in the future.

1500 km.

After the run-in period, the high speed can be pulled.

No effect.

Our new car in the normal use of the process, will naturally on the car engine, calipers, brake discs, tires for the run-in, we usually take the first 1500 kilometers of the car as the new car run-in period, as long as we drive normally during this period, do not brake sharply to make the car overloaded to achieve the real sense of the run-in. Generally, the new car just mentioned, the 4S shop will notify us to carry out free first maintenance at about 3000 kilometers, and the performance and handling of the car after the first warranty will reach our ideal state.

Therefore, there is no need to deliberately go to high-speed running-in for the new car we just mentioned, even the constant wear and tear parts that need to be run-in will get the run-in we should get when we use the car in our daily life. We love cars, but we need to know cars!

It's up to you to decide.

Break-in period. The running-in period generally refers to the process of contact, friction and occlusion of mechanical parts in the initial operation. In modern times, it is often used to describe the period of mutual familiarity and adaptation of two things or the internal operation of an organization, and it is also used to describe the stage of relationship and marriage and mutual contact and familiarity.

Run-in is also called walk-in. The car run-in period refers to the initial driving stage after the new car or overhaul, generally 1000 1500 kilometers, which is the basic mileage to ensure that the parts are fully contacted, rubbed, adapted and finalized. During this period, the ability of each part of the car to adapt to the environment can be adjusted and the protrusions on the parts can be sharpened.

The quality of the car run-in will have an important impact on the life, safety and economy of the car. After leaving the factory, although the new car has been run-in, the surface of the parts is still rough. In addition, there are certain deviations and some hidden dangers that are difficult to find in processing and assembly.

In addition, there are many metal particles falling off between new parts and accessories, which not only aggravate the wear between parts, but also reduce the quality of the oil after falling into the oil, which affects the lubrication effect. Since the new parts have more frictional resistance during operation than in normal times, the fuel consumption will also be higher.

High speed, which refers to advanced speed, is compared to medium and low speed. In an environment where low speed is predominant, low speed is normal or normal, while in an environment where medium speed is predominant, medium speed is normal or normal.

The relationship between high speed and fast: the generalized fast in the dichotomy (fast and slow comparison) includes high speed relative to slow speed, but the word fast does not mean high-end, and in multi-object comparison, fast is higher than low speed and lower than high speed and quasi-high speed. In the rule of thirds, the fastest is the medium speed, which is higher than the normal speed and lower than the high speed.

In the rule of thirds, expressways are lower in specification than highways, rapid railways are lower in specification than high-speed railways, and rapid trains are lower in specification than high-speed trains.

Pulling the highway doesn't have to go to the highway to run fast. Just increase the speed accordingly during operation, which is conducive to reducing the carbon deposit of the engine.

You can run a new car when you buy it, this run-in refers to how many kilometers of stable driving benign wear and tear, as long as you develop good driving habits, don't step on the accelerator and brake and don't run to tell it, my car has not pulled the high speed, and now the run-in is very good, and the fuel consumption is also very average.

It depends on whether you pay attention to this thing. It's okay if you don't pay attention to it.

No more than 80 within 2000 kmSmooth acceleration, braking. Don't jerk the oil. Reduce sudden braking... After 2000, I got off the highway.

Normally, it is after 2000 km, but according to personal use, even if you are on the highway, you just need to control the speed of the car not to exceed 80km/h.

It's best to go up after 3000.

Each car may be slightly different (e.g. speed), but the principle of speed is the same, let's take a look.

500 kilometers for the initial run-in, at this time the speed should not be too fast, generally 70-80 kilometers below, the speed should not exceed 2200 rpm as well.

1000 kilometers is the mid-term run-in, the maximum speed can be appropriately increased, generally can reach 90-100 kilometers, and the speed is still below 2500 rpm. Increasing the speed appropriately will not only not affect the engine, but can promote the running-in, and you can see if there is any abnormality when the speed is increased again.

1500 kilometers is the later run-in, and the speed can be increased to less than 120 kilometers. Because running-in is a gradual process, it must be gradually increased. The speed should not exceed 3000 rpm.

4. When all cars are driving at low speed, the actual burden is greater than that of medium speed, so the run-in period should not be run in below 60 kilometers per hour for a long time. The speed must be increased gradually. At the same time, if you have been running at a speed of 80 kilometers per hour after the run-in period, a sharp increase in speed will make the new car unadaptable, so it is necessary to gradually increase the maximum speed during the run-in period.

5. Do not drive at a fixed speed for a long time during the run-in period, and there should be a speed change.

6. Avoid sudden braking and rapid acceleration during the running-in period.

In the case of automatic transmission, the run-in specified gear cannot be determined by manual gear shifting, so it can only be achieved by driving speed. In short, the run-in should be driven at a constant speed, and the levels of 30km h, 60km h, 80km h, and 100km h must be stable. It is recommended to get it on the flat road around 10 p.m.

The general car series is about 5,000 or less, and the good ones can be more, but it mainly depends on the road conditions you usually drive, the run-in period should not exceed 80, and the run-in can be 3000 kilometers.

You need to pay attention to the following points during the run-in period of a new car:1The engine speed should not be too high, preferably not more than 3000 rpm.

2.There should be a process of warming up the car during the cold start, and driving on the road after the water temperature changes, generally about 5 minutes. 3.

The number of loads must be reduced according to the load regulations of the model, and it is advisable not to exceed 70% of the specified load capacity. 4.The impact damage of the sudden braking on the engine, braking system and chassis of the new car is very large, and the situation should be dealt with in advance and the gear should be reduced in the middle of the car.

5.Avoid refueling and braking the Yinshi car urgently, and try to maintain a constant speed. The maximum speed within 2000 kilometers should not exceed 90 kilometers per hour, but it is not possible to drive at low speed for a long time.

6.According to the time and mileage specified by the manufacturer, go to the 4S store for the first oil change; After driving to 2000 kilometers, you can go to pull the high-speed, when pulling the high-speed, you should pay attention to the use of each gear to pull the gear to 3000-3500 rpm on the gear can be pulled to 4000-4500 rpm, 5 gears to reach 4000 rpm when the speed will be too high, you can pull it appropriately, in each gear respectively 3 5 minutes, the new car should go to the 4S shop to replace the oil filter in time after the high-speed.

Hello, it is recommended to be able to first ensure that you can go to pull the high-speed, why do you say that, the oil during the run-in period of the new car will more or less run out of some iron filings and the like, the first insurance to change the oil when it is released, and then go to pull the high-speed better, I hope to help you!

Generally 60-80, drive to more than 3000 kilometers, you can pull the high point.

Hello, according to your situation and our maintenance experience, now the vehicle does not need to deliberately run-in, you can refer to the user manual to drive, do not need to pull the high speed, it is not recommended to drive intensely or violently, you can usually drive, I hope my answer makes you satisfied, I wish you a happy car.

Hello, it is recommended that you do not exceed 1000 before the first insurance, and the speed should not exceed 3,000! It is better for you to use the engine in the future!

5000 5000 after going to the highway to pull a pull.

Do not exceed 100. After the first insurance, it can pull the high speed.

After 10,000 kilometers, you can pull the high speed.

Pull high speed instead of running high speed! The real meaning of pulling high speed is to pull the high speed of the engine. Pull the speed of each gear to more than 5000 rpm, so that the piston and gear can try to work at high speed and achieve the meaning of pulling high speed.

Pulling the high-speed generally means that the new car has passed the run-in period to get on the high-speed to pull the car. The idea was to get the new pistons and camshafts inside the engine to try to work fast for the first time, so that they had better intimacy with each other. In addition, the gears in the gearbox can be rotated at high speeds, so that the joint between the new gears and the gears is smoother.

By pulling the high speed, the car can have good power in the future driving and smooth gear changes. If the road conditions allow, I drove to 140km h or even higher with the top gear on. This can't be called pulling high-speed, at best it can be called driving high-speed.

This not only fails to achieve the significance of pulling the highway, but also wastes gasoline in vain.

During the run-in period, the general run-in period is about 3000 kilometers, a lot of metal chips and other impurities have entered the oil, the absorption capacity of the oil for impurities tends to be saturated, so the first step of pulling the speed is to change the oil, after the change, drive dozens of kilometers, so that the new oil and the engine are fully contacted. The second step is to find a road section with good road conditions, starting from 1st gear to 5th gear, and maintain each gear at about 4000 rpm (full rev gauge 4 5 or so rpm), and insist on 5 to 10 minutes respectively. Finally, go for the oil change.

The oil is more capable of cleaning when circulating at high speed, and the oil is the dirtiest after pulling at high speed, so it is replaced at the time of the first maintenance. After these steps, your car's engine block, pistons, crankshaft, propeller shaft, transmission gears, and moving parts are more deeply connected.

Hello owner, there is no need to pull the high-speed car now, and the high-speed only needs to pull 4000 rpm, 140 on the line.

100% wrong, during the run-in period of the new car, the speed does not exceed 3,000, and it doesn't matter how fast the speed can run, the correct way.

The instructions will generally indicate whether it needs to be run-in, if it is not indicated, there is no need to deliberately run in, as for the high-speed do not do it deliberately, let it be, of course, the city's stop-and-go congested roads must be more than the highway sediment

It is not necessarily on the high speed, the new car is 80 to 100 to be conducive to the meshing between the gears, but the speed should not be too high, try not to exceed 110 during the run-in period, and it is OK at 75 to 95.

No, it's good to drive normally, and it's good to warm up for two more minutes after the new car gets on fire.

Wrong, the new car should be driven slowly, and it will not be pulled until after 5000.

If it's a van, it's not necessary.

More than 300,000 is OK.

The new car should not be pulled at high speed and hurt the car. Smoothness.

After the run-in period (7500 kilometers after the complete run-in), of course, we have to pull the high speed like our car mileage of more than 6000 kilometers when we go to the appropriate walk, when the engine speed is maintained at 4000 rpm, the speed of the car does not exceed 160km h. When the run-in period is completely out of the run-in period, before the maintenance and oil change, it will be completely pulled at high speed, and the speed will basically be maintained at 5000 rpm for a period of time. Cleaning up the engine carbon deposit is such a thing, often driving in the urban area, stop-and-go, the engine speed usually does not exceed 2500, that is easy to produce carbon deposit.

It will affect the performance and fuel economy of the car. And to clean up the charcoal, it is also very simple, just run at a slightly high speed, go to the national highway for a walk, hang a low gear, and keep the speed at 3000 for a while.

Yes The car runs at high speed to remove carbon deposits and it can be done at any time without any run-in period.

There is no requirement for this, and it is generally necessary to clear the carbon deposit at the time of the first insurance! But running at high speed before the first insurance is to find out what problems the car has at high speed, so that it can be dealt with in time during the first insurance!