Premiere exported only a portion of the movie, which was supposed to be 6 and a half minutes but onl

Your work area only contains the previous 2 minutes and 14 seconds, and the range of output settings selected is the work area, so only this part is output, the solution is: file-output-video, after the dialog box appears, select the settings in the lower right corner, in the general tab, select the range as "entire timeline".

You can try to render it piece by piece and find out what's wrong, and if it can be rendered green, that's fine, otherwise check the special effects or stuff like that.

Solve 500 points? Then I'll help you think about it. First of all, do you use a lot of special effects?

Transition-like or special effects. You're in the software** to see if every special effect can appear? If some effects don't display properly, try a different effect until it can be displayed.

And then render the settings, are you sure you're setting the entire timeline and not the work area? If you can't export in sections, you can effectively check for paragraphs that can't be exported. And then it's relatively simple to solve.

requirements. I'm afraid there is no good solution. You can use "PowerDirector", CyberLink launched the world's fastest and most advanced ** software, I have used it, to make a wedding video for my friends, it is indeed very good.

1. The disk memory is full.

2. There is a problem with the final clip or another clip is selected to export.

1 First, open the PR software on your computer.

<>3 Then click "Info" on the left.

<>5 Finally, press the shortcut key "Ctrl M" to open the export interface, in this interface, change the width and height values to be the same as the original **, and click Export below.

Summary. Only half of the reasons for exporting may be due to incorrect export settings or incorrect scaling. Here are the possible causes and workarounds for the issue:

1.Incorrect export settings: When exporting, you need to set the output parameters (such as resolution, frame rate, bitrate, etc.) correctly, otherwise the output may be incomplete or distorted.

It is recommended that you check that the export settings are correct and adjust them accordingly as needed. 2.Incorrect scaling:

If you set the scale when exporting, but the scale is incorrect, it may result in only half of the output. In this case, you can check if the zoom setting is correct and adjust it as needed. 3.

Unsupported encoding formats: Some encoding formats may not be supported by some devices or devices, resulting in only half or no output at all. It is recommended that you select a commonly used encoding format (such as etc.) and use a device that supports that format.

4.Software problems: Sometimes there will be some abnormal conditions in the PR software, such as sudden crashes or lagging, which may cause only half of the output.

You can try restarting the software or updating the software version to see if that resolves the issue. In short, if you encounter the problem that the export is only half of the problem, you can first check whether the export settings and scaling are correct, and choose the commonly used encoding format for output. If the problem persists, it is recommended that you seek professional technical support to help solve it.

There are four possibilities, and you need to find out the cause according to your own situation.

Can you add, I don't quite understand it.

Only half of the reasons for exporting may be due to incorrect export settings or incorrect scaling. The following are the reasons and solutions that may lead to this question:1

Incorrect export settings: When exporting, you need to set the output parameters (such as resolution, frame rate, bitrate, etc.) correctly, otherwise the output may be incomplete or distorted. It is recommended that you check that the export settings are correct and adjust them accordingly as needed.

In this case, you can check if the zoom setting is correct and adjust it as needed. 3.The encoding format is not supported:

Some encoding formats may not be supported by some devices or devices, resulting in only half or no output at all. It is recommended that you select a commonly used encoding format (such as etc.) and use a device that supports that format. 4.

Software problems: Sometimes there will be some abnormal conditions in the PR software, such as sudden crashes or lagging, which may cause only half of the output. You can try restarting the software or updating the software version to see if that resolves the issue.

In short, if you encounter the problem that only half of the export is exported, you can first check whether the export settings and scaling are correct, and choose the commonly used encoding format for output. If the problem persists, it is recommended that you seek professional technical support to help solve it.