Computer won t go into normal mode? What s going on with the computer going into setup mode all the

I hope I can help you solve your problems, and I hope you can also give me more points, thank you!

First confirm whether your machine has two memory, if you only plug in one memory to try, or if it doesn't work, kill it with a nod32 antivirus software, and make sure there is no virus first! Then determine if it's your system's problem, if so, follow my method, I guarantee that your computer is 100% stable:

1-First of all, format the system, use format c: format under DOS, do not add q fast grid parameters, slow grid, so that you can completely remove the C disk file!

2-Secondly, reinstall the system, don't use the original or gohost version of the system, it's best to change the version, I personally recommend using the commonly used on the Internet [Depth XP Lite only this version of XP is the best to use, if your machine is an old machine, it's better! This version does not support foreign input methods,Other functions are must-have!

3- After installing the system, put the cache of the C drive in another area, and install the software and games to be installed on the D drive, so that your machine will be fast!

4- Don't be happy yet, and there is more! It is recommended to use NOD32 antivirus software, in.

Search, put NOD32 and its registrar down to your computer to install, if nod32 often prompts registration problems in use, just re-register with the registrar, convenient, forever free!

5- Finally, re-optimize with the optimizer, just leave the icon at the bottom right of the computer with an icon of [volume], as if there is a word starting with [c] don't optimize it!

6- If the above work is completed, don't believe in any registry optimization on the Internet, those are all deceptive plays, just use what I taught you, you can use ghost to back up the system, after the system has problems, first format the C drive, and then restore the system! Well, that's all!

7- In this way, no matter what software you use or play games in the future, your computer will be guaranteed to run in the most stable and fastest state.

Press F8 to select the debugging mode during the boot process.

The computer has been entering the setup mode, generally because the system is faulty or the hard disk is faulty (including data cables) or the boot sequence is not set.

1. If the system fails, the system will be reinstalled to solve.

2. Hard disk failure (including data cable) can be solved by slag replacement.

3. Boot sequence fault solved, boot press the del key, enter the BIOS --- boot item, and find the "boot option properties" - boot options

Modify it to the hard disk model and press F10 to save and exit.

How should I enter the safe mode of my computer?

Is it possible that the system has not been installed and entered the safe mode, can you enter the normal mode, and the hardware is fine, and then disconnect the network cable and install the system? Try replacing all the hardware with a different computer? Did you use it normally before, and how did you install your system?

In this case, you can only install the system again, and it is best to format the hard disk according to NTFS.

In this case, the MBR of the main boot sector of the disk is corrupted, and it can be repaired with a boot USB flash drive, the specific method is as follows:

Step 1: Make a boot USB flash drive.

2. Select the USB flash drive mode, select HDD-FAT32 for the production mode, and press "One-click Production".

3. In the future, just wait, when making, remember not to move the U disk until the production is completed.

Step 2: Start the USB flash drive.

1. Plug in the USB flash drive and reboot it.

2. Generally, press F12 to enter the boot menu, select the U disk, and you can start.

3. If it is not F12 quick start, press the DEL or F2 key to enter the BIOS, set the U disk as the first boot in the Adanced BIOS Featuces or Boot startup item, please operate according to the instructions of the computer, and then press F10 to save and exit.

4. Restart the computer, it will automatically enter the USB flash drive.

Step 3: Modify the main boot sector of the disk.

1. After booting from the USB flash drive, select PE for installation.

2. After entering the PE desktop, launch the DiskGenius software, which will be available in this tool PE.

3. On the main interface of the program, open the "Hard Disk" menu.

4. Select the item "Rebuild Master Boot Record MBR" under it.

5. The repair can be completed in a few seconds, exit the PE, restart the computer, and you can enter the system normally.

6. If the above methods do not work, reinstall the system.

USB flash drive boot disk to reinstall the system.