How to deal with moisture in the printer? What to do if the printer paper is wet

First of all, the first thing to do before going to work every day is to turn on the photocopier to warm up, which can be used to dry the moisture and small water droplets inside the equipment;

The company can try to avoid the opening of doors and windows, a large amount of ventilation will cause the indoor humidity to rise, resulting in paper jams, paper moisture, unclear printing output and other situations. Secondly, you can turn off the copier switch after work every day, but do not unplug the power plug to ensure that the inside of the copier can be kept dry at night.

In addition, when placing office equipment, it should be kept away from relatively humid locations such as mineral pots, water sources, and water dispensers, which can prevent moisture failures caused by the indoor environment. After the refrigeration, a box of desiccant can be placed in the photocopier carton rented by Dongcheng color copier to keep the paper dry and reduce the phenomenon of paper jams. Do not expose paper to the air, and implement a system of using as much as you want.

1.If the printer gets water, you need to disconnect the power immediately, regardless of where the machine gets into the water.

2.If only the surface of the machine is flooded, find a clean cloth to wipe the area with water, wait for the machine to dry completely, and then turn on the machine.

3.If water gets into the machine, immediately contact the after-sales maintenance center, and the master of the maintenance station will disassemble and clean the machine.

Note: Do not turn on the machine in the case of water ingress, as it may cause damage to the internal hardware of the machine and short circuit.

You should do your hand from 2 aspects:

1. Dry the printer in a ventilated place.

2. Draw out the ink cartridge to avoid moisture.

The most important thing is to try your luck and see if you can get a new one.

It is better not to use a hair dryer, because his wind has the phenomenon of heat accumulation, so as not to burn some parts inside.

Moisture can not be dried, otherwise it can not be used, it will cause jams, once the moisture is uneven, it will curl, jammed paper, etc.! Is it A4 copy paper or printer paper with holes? A pack of more than a dozen yuan, you can use it for drafts, so as not to be annoying with paper jams.

1. External environment: The temperature of the photocopier is insisted on at 15 degrees Celsius.

Insist on humidity at 25 to 75%, place the machine in a dry place when placing the photocopier, and keep away from drinking oak water machines, mineral pots, and water sources. In this way, malfunctions due to moisture in the room can be avoided.

2. Ventilation: In the humid room, ventilation should be insisted on to reduce the humidity in the room, and prevent problems such as paper jams and unclear prints. Preheat and dry: Every morning after work, turn on the copy reed machine to preheat the moisture in the dryer.

3. Paper moisture-proof: insist on paper dryness, and place a box of drying agent in the photocopier carton to adhere to the dryness of paper. After using up the copy paper every day, wrap the copy paper and put it in a boring cabinet. Try to avoid leftovers every time you use copy paper.

4. Power supply: After getting off work every day, after turning off the switch of the copier, do not unplug the power plug, so that the photocopier will be boring at night. Rainy weather:

In rainy weather, pay attention to the moisture protection of the copier. During the day, it should be turned on and insisted on boring, and at night to avoid moisture entering the machine.

A photocopier is one of the essential pieces of equipment in a modern office space. However, if the copier is wet, it will affect its normal use, and even short circuit or damage. So, what to do if the copier gets wet?

As a first step, immediately cut off the power supply and unplug it. If there is a fire extinguishing switch between the electrical outlet and the wire, it should be turned on.

In the second step, the moisture inside the photocopier is removed. All removed parts can be cleaned, including flat glass, A4 trays, toner cartridges, driver cartridges, and more.

The third step is to dry all parts of the copier. Circuit boards and electrical components, in particular, must be thoroughly dried to ensure that there is no short circuit. It is best to use a soft cloth or cotton yarn with good water absorption and trembling smile.

Step 4: Place the photocopier in a ventilated and dry place. You can use a hair dryer or air conditioner to speed up drying. However, be careful not to blow the hair dryer or air conditioner outlet directly inside the copier, so as not to cause other problems.

Step 5: Wait for at least 24 hours to turn on the power again. Always make sure that the individual parts are completely dry before restarting. Otherwise, moisture may cause damage to the circuit board and electrical components.

In short, when the photocopier is damp, it is necessary to stop using the source immediately and take a series of necessary measures to deal with it. If you can't handle it yourself, it's best to ask a professional technician to overhaul it. This ensures the proper use of the copier and avoids bigger problems.

When the photocopier gets wet, the impact on the machine is very large. The humid environment can easily lead to problems such as short circuits on the circuit board, damage to the printer motor, and clogged ink cartridges. If it cannot be dealt with in time, it will affect the normal use of the machine. Here are a few ways to repair a photocopier after it gets wet.

Method 1: Dry with an electric fan.

When you find that the photocopier is wet, you first need to turn off the power of the machine. Then, use an electric fan to blow dry the machine, especially the printer motor and circuit board. During the blow-drying process, it is necessary to carry socks to avoid blowing into the ink cartridge and other vulnerable parts.

In addition, if the photocopier has been damp for a long time, it is recommended to disassemble the machine and dry the internal parts separately.

Method 2: Place desiccant to absorb moisture.

After the machine is blow dry, some desiccant needs to be placed inside the copier. For example, you can put a packet of desiccant in the cartridge compartment or in the light box of a projection device. The desiccant has a good effect of absorbing moisture, and the machine can be completely dried in one day.

Method 3: Replace the parts.

Sometimes, moisture on the copier, which may cause damage to certain parts of the machine, such as circuit boards, printer motors, etc. At this point, these parts need to be replaced. In general, the accessories of the popular models of photocopiers can be purchased on the market.

It should be noted that when replacing parts, you need to ensure that you are skilled in operation, otherwise it is recommended to seek the assistance of professional after-sales first to avoid damage to the machine hidden grip or greater loss.

Method 4: Repair.

If the photocopier still does not work properly after being wet, it is recommended to take the machine to a professional repair facility for repair. The repair shop will conduct a thorough inspection of the copier, determine the root cause of the problem, and repair or replace the relevant parts. Before making a repair, it is advisable to ask the repair shop's professional for repair options and estimated costs.

To sum up, when the photocopier is wet, it needs to be cleaned and repaired in time. Be careful to turn off the power of the machine before handling to avoid electrical shock. For copiers with minor conditions, using an electric fan to blow dry and place desiccant will do the trick.

For more serious copies, replacement parts or professional repair are required.

The photocopier is damp and does not lack seepage to use, put it in a ventilated and cool place, leave it for a period of time, and then turn on the power for a period of time to try to make the volcanic ridge use, if there is a specific problem, in the specific solution.

The printer cannot be turned on when it is exposed to moisture because moisture seeps into the inside of the printer, causing a short circuit or corrosion of the circuit components, making the printer unable to function properly. If this happens to any brigade, there are a few steps you can take to deal with it:

1.Disassemble the printer.

If the printer is already wet, you can try disassembling the printer. Unplug the power cord first, then disassemble the case to see if there are any visible signs of moisture inside. If high humidity is found, a moisture absorber can be used to absorb moisture.

2.Dry the printer.

After disassembling the printer, dry the internal components separately. You can dry the inside of the printer with a fan or natural breeze. Do not use hot air for drying to avoid aggravating the damage.

3.Cleaning. If you find sewage or stains inside the printer, you can wipe it with a clean cloth or clean it with alcohol, but be sure to pay attention to safety and pay attention to fire prevention.

4.Replacement of components or repairs.

If the printer is badly damaged, it is recommended to replace the components or repair them, which requires you to seek professional help.

5.Moistureproof. During daily use, care should be taken to keep the environment dry to prevent moisture from entering the inside of the printer. Tools such as dehumidifiers can be used to keep the environment dry.

In short, after the printer gets wet, don't be too anxious, don't use force right away, you should think about how to drain the moisture out of the printer. Prompt treatment is key so that damage can be prevented. If it really doesn't work, you can contact a professional maintenance personnel for repair.

If the printer doesn't get wet for a long time and won't turn it on, you can move it outside, let it dry for a while at noon, and then turn it on.