How to adjust the microcomputer time control switch, and how to set the microcomputer time control s

Press and hold the [Cancel Resume] button for about 3 seconds to turn on or remove the keypad lock. Adjust the clock: Press and hold the [Clock] button, and press the [Hour], [Minute], and [Day] keys at the same time to adjust the clock and day.

The steps to set the schedule are as follows:

Steps. Keystroke. Set up the project.

Press the [Time] button.

Enter the 1st set of timed on settings (1 on display).

Press the [Day], [Hour], and [Minute] keys respectively.

Set the opening time (day, hour, minute).

Reset the [Time] button.

Enter the setting of the 1st set of timer off (display 1 level).

Press the [Day], [Hour], and [Minute] keys respectively.

Set the time (week, hour, minute) to turn off

Repeat the steps.

The time of 2-10 sets of switches can be set.

Press the [Time] button continuously.

Check whether the switching time and day of the week for each group are the same as required, and if it is incorrect, you should also repeat the step Press the [Auto Manual] key.

Match the switch to (".)

Adjust to the state you are in at the current time ("On" or "Off") and then back to the "Auto" position.

Press the [Clock] key.

The end time is set to enter the clock display state.

Note: If you do not need to set 10 groups, use the [Cancel Recovery] key to eliminate the excess number of groups, and display "--that is, elimination, if you press the [Cancel Recovery] button again, you can restore the original time setting before elimination.

The KG316T microcomputer time control switch can set multiple groups of on/off control, can be grouped into groups, etc., according to your requirements only set two groups on the line.

Set the timer to Beijing time first, and then press the "Timing" button on the panel, and the screen will display "1 group on·—."

—Then press the "Calibration" key to adjust to 18 00, and press the "Timing" button on the panel twice, and the screen displays "1 group off·—

—After pressing the "calibration" key to adjust to 00 00, continue to press the "timing" button on the panel, and the screen displays "2 groups on·—

—Then press the "time" key to adjust to 5 00, and press the "timer" button on the panel twice, and the screen displays "2 groups off·—

- After pressing the "calibration" key to adjust to 8:30, press the panel "clock" key to exit, and finally press the panel "automatic manual" key to adjust to the automatic position to complete the setting, so that it will be repeated every day.

How to set the function of the microcomputer time control switch and its application, you will know at a glance.

1. Press the "Cancel Recovery" button first to unlock the screen.

2. Then press the "Calibration" button to calibrate the hour, the "Calibration" button to calibrate the minute, and the "Calibration" button to calibrate the week.

3. Press the "Timing" button again to set the power on and off time.

4. Then press "Timing" to continue to set the second on/off time, and so on, you can set more than a dozen, but generally only need to set one.

5. Press the "Auto Manual" button to "Auto", and you can turn on and off regularly.

6. After the settings are completed, press the "Cancel Recovery" button to lock the screen and you're done.

7. The finished effect is shown in the figure below.

Microcomputer time control switch time adjustment method:Tool Raw material: a time-controlled switch.

Method Steps:1. Press the timing button, first press the second timing button below the time control switch, and turn on the setting mode of the switch.

2. Use the upper button to adjust, press the two buttons on the right to adjust the specific number of hours and minutes, and then press the timing button after the opening setting is completed.

3. When you come to the off mode, you can also use the above two buttons to adjust the numbers of hours and minutes.

1. First of all, you need to enter the operation interface, different models, the operation method is inconsistent, but it is similar, the "Cancel Recovery" button is pressed 4 times in a row, and the screen is unlocked.

2. The method of adjusting the time crack: while holding down the "clock" button, check whether the time displayed on the display screen is the same as the current time, and press and hold the "school week", "school time" and "school time" keys respectively to adjust the clock to the current time.

3. Timing method: press the "automatic manual" button to adjust the symbol below the display to the "automatic" position, at this time, the time control switch can automatically open and close the circuit according to the time set by the mountain crack. Then press the "Timing" button, then press the "School Week" to select the five-day working system, the same every day, and the different working modes every day, and then press the "Calibration Time" and "Calibration" buttons, enter the required opening time, and then press the "Timing" button, and then press the "Calibration Week", "Calibration Time", "Calibration" key, enter the date and time that you need to close, and the timing is successful; Continue to press the "Timer" key and repeat the above operation to schedule multiple times.

4. The microcomputer time-controlled switch is a power switch control device with a single microprocessor as the core and electronic circuits, which can control the opening and closing of household appliances in a daily or weekly cycle and multiple periods. It is suitable for the automatic control of various industrial Weixiang electrical appliances and household appliances, which is safe and convenient and saves electricity and money.

The microcomputer time control switch, the method of adjusting the time is as follows:Tools Raw material: CHINT KG316T.

1. Press the first recovery button four times in a row to unlock the time switch.

2. Press the buttons for the next three hours and minutes and the day of the week to align with the current time.

3. Press the timer button again to enter the open timer setting interface.

4. Press the button when you press to adjust the hour time of starting, and press the button of minutes to adjust the minute time of opening.

5. Press the week button again to adjust the specific time of the lease to be opened, and then press the timing button after adjustment.

6. After entering the timing setting interface of the front type tan to the off, press the three buttons to adjust the specific time.

7. After all the adjustments are made, press the clock button and return to the start interface.

1. Check whether the clock display is consistent with the current time, if you need to re-align, press and hold the "clock" button at the same time, check whether the time displayed on the display screen is the same as the current time. Press and hold the "School Day", "School Time", and "School Score" keys respectively to adjust the clock to the current time. 2. Press the "Timing" button, and the word "1 on" appears at the bottom left of the display screen (indicating the first time it was turned on).

Then press "School Week" to select a five-day work system, the same work mode every day, and a different working mode for each day, and then press the "School Time" and "School Score" buttons to enter the desired opening time. 3. Press the "Timing" button again, the words "1 off" appear at the bottom left of the display screen (indicating the first closing time), and then press the "school week", "calibration time", "proofreading" button, enter the date and time required to close 4, continue to press the "Timing" button, the lower left of the display screen will display "2 on/off, 3 on/off on", refer to the steps to set the switch time in the future. 5. If you don't need to set 10 sets of switches every day, you must press the "Cancel Recovery" button to eliminate the excess time of each group and make it display on the display screen "--pattern" (not 00:

00)。6. After the timing is set, press the "Clock" button to make the display display display the current time. 7. Press the "Automatic Conversation Paragraph Manual" button to adjust the "" symbol below the display to the "Automatic" position, at this time, the time control switch can be set according to the setting.

Take KG316T as an example:

1. Press the cancel button first.

2. Press the calibration button to check the time.

3. After that, the proofreading button proofreads the minutes.

4. Then press the school week button to proofread the week.

5. Different calibration buttons, different proofreading time.

Different models have different setting methods, please follow the device instructions for setting.

Microcomputer time-controlled switch setting and wiring.

Easy steps: 1, "Clock" key (adjustment) - 2, "Manual" key (enter) - 3, "Set" key (set) - 4, "Clock" key (end) - 5, "Set" key (check) - 6, "Cancel" key (modify) - 7, "Clock" key (end check) - 8, "Manual" key (control switching).

Specific steps: 1. Use the "clock" key - open the keypad lock and adjust the Beijing time: press and hold the "clock" key + "cancel recovery" key for a few seconds at the same time, and switch between the lock display sign and "unlock"; At the same time, press and hold the "Clock" button + "Day" button, "Hour" key and "Minute" button to adjust Beijing time in turn, that is, the day of the week, what time of the week, and how many minutes.

2. Use the "manual" key to enter the setting state: press the "manual" key to move the inverted triangle of the display to the "automatic" position, and then you can enter the setting state.

Use the "set" button - set the day of the week and switch time: after pressing the "set" button for the first time, enter the timer opening setting (at this time, the screen displays 1 on), press the "day" button, "hour" key, and "minute" key to set "each" for the week.

Depending on the day, different days, different days, same Monday to Friday, or same Saturday to Sunday, you can set the specific time of "on", i.e., what time it is. Press the "Set" button again and enter.

Enter the timer off setting (the screen shows 1 off at this time), press the "hour" button and "minute" button to set the time of off. Finally, repeat the switching time from the 2nd to the 12th time. Because the program has 12 programs, it is generally only set for program 1.

It will definitely meet the requirements of most people.

4. Use the "clock" button - end the setting of the switch time: after the setting, press the (clock) button and return to the actual time to end the setting of the switch time.

If the setting is wrong or the setting is canceled, press the "Cancel" button and press again to restore the original setting.

Displayed when there is no setting (

5. Use the "Set" button to check whether all set times are correct.

6. Use the "Cancel" button to modify the set time: press the "Cancel" button at the setting to reset the timing switch time and week.

7. Use the "clock" button - end check: press the (clock) button to end the check and setting, and display the clock.

8. Use the "manual" key - enter the manual automatic control switching: press the "manual" key to realize random opening and closing or automatic operation.

The method and steps of setting the time of the microcomputer time control switch:

Tool Raw material: microcomputer time-controlled switch.

1. The first step, firstly, press the "Cancel Recovery" button to unlock the screen;

2. In the second step, now we need to press the "Calibration Time", "Calibration" and "Calibration" buttons in turn to check the hours, minutes and weeks respectively;

3. In the third step, press the "Timing" button to set the on/off time, and so on, you can set more than a dozen;

4. In the fourth step, we need to press the "Auto Manual" button, and adjust it to "Auto", and then turn on and off the machine regularly;

6. Next, we have completed the time setting of the microcomputer time control switch, and then we need to press the "Cancel Recovery" button to lock the screen.

Hello, glad to answer for you! 1. Press the "Clock" button once, then press the "Calibration" button, "Calibration" button and "Calibration" button respectively to adjust the clock to the current time, and then press the "Clock" button to confirm after setting, the LCD screen will display the current time. Turn left|Turn right to turn left|Turn right 2

Press the "Timing" button, the word "i on" appears at the bottom left of the LCD screen (indicating the first turning time), then press the "Calibration Week" button, "Calibration" button and "Calibration" button, and enter the desired opening time. Turn left|Turn right to turn left|Turn right 3Press the "Timing" button again, the word "I off" will appear at the bottom left of the LCD screen (indicating the first closing time), and then press the "Calibration" button, "Calibration" button and "Calibration" button to enter the desired closing time.

Turn left|Turn right to turn left|Turn right 4Continue to press the "Timer" button, and the lower left side of the display will be displayed in turn (2 on, 2off, 8 on, 8off).

Questions. It is only set until Monday to Thursday.

I hope I can help you and I wish you a happy life!

Can't you set it on Friday and Saturday.

Questions. Closed on Fridays and Saturdays.

Required to be closed on Fridays, Saturdays and Sundays.

Can you set it? Yours is key-based or Bluetooth-based.

The push-button time-to-switch week setting is fixed: one.

Two. Three, four, five.

Six, one three. Five, two, four, six, etc., can not be arbitrarily chosen.

The Bluetooth time control switch can be set according to the needs of the click to select (random combination selection).

Questions. Delixi pressed the key.

Just press and hold the "Clock" button without letting go, then press "Week" to set the day, "Hour" to set the hour, and "Minute" to set the minute.

Set the opening time of the first period: press the "Timer" button, the LCD display displays, the word "1 on" appears, and then press "hour" and "minute" to set the time to turn on.

Press the "Timer" button and then the "Week" button to set which day of the week to turn on and off at the set time.

This way you can set Monday to Thursday open.