I just changed the motherboard, the blue screen can t enter 0000007B, unplug the power of the main h

There is a system from the disk on it! If you don't, you can't!

1. The computer blue screen is caused by poor contact of the memory module or memory damage.

In actual work, the most common computer blue screen phenomenon is the poor contact of the memory module (mainly caused by too much dust inside the computer, which often occurs in old computers) and the computer blue screen caused by hard disk failure. Of course, when the computer memory module fails, the computer blue screen phenomenon will also occur.

Solution: Since most of the blue screen failures caused by memory are caused by too much internal dust or poor contact, the solution is also very simple, you only need to open the computer case, pull out the memory module, clean the lower slot and clean the gold finger of the memory module and then install it back, and the general problem can be solved. If the problem is not resolved, it is determined that it is a memory failure, and replacing the memory module can resolve the issue.

2. If the computer system has just been installed, it is best to use the driver in the free disc of the installation hardware when the driver is installed, because the driver is incompatible with the hardware may lead to the blue screen phenomenon. If your computer has been used for a while and you haven't seen a blue screen, but one day it suddenly has a blue screen, it may be that there is too much dust in your computer and it's time to clean it up. It may also be caused by the incompatibility of the software and the computer system.

3. The high temperature of the internal hardware of the computer is also a common reason for the occurrence of the blue screen phenomenon of the computer, and the internal temperature of the computer is very high, at this time, the temperature of the hardware can be detected, if it is found that the temperature of the CPU, graphics card or hard disk is particularly high, then it is likely that the computer blue screen is caused by poor heat dissipation.

Solution: If it is caused by the temperature of the CPU or graphics card, then turn on the computer to see if the CPU fan and graphics card fan rotate normally, if it is normal, it is recommended to strengthen the heat dissipation of the host, such as adding the chassis for heat dissipation, etc., if the temperature of the hard disk is too high, there may be a hard disk failure and need to be replaced.

Blue Screen** 0x0000007b solution.

You disassemble the parts and put them back on, I also tried, and as soon as I got to the splash screen, it was a blue screen. Just take him apart, polish it and put it back on.

7b**Blue screen, the hard disk mode is not set correctly, you can change it in the BIOS.

But if you change the motherboard, the relevant drivers have changed, so in order to run stably in the future, it is better to reinstall the system.

win7 computer system blue screen 0*0000007b** how to solve?

1. When you encounter a problem, you should think more and eliminate it slowly. Unless it's a hardware problem.,Hard disk bad sector or a problem like a fall,Otherwise,There will always be a solution,Reinstalling the system is the best policy,If it's this problem,Reinstall the system may still not be solved,Because win7 may not come with a RAID driver。

2. If you google earlier, this problem can be solved in a minute, and a lot of time is wasted.

0x0000007b This ** has something to do with the hard disk, but don't be afraid, it's not a bad sector, it's a hard disk boot partition error caused by a setting problem or a virus.

Press the DEL button or F2 button on the motherboard interface to enter BIOS1, select Boot, and enter the boot interface.

2. Find the boot item and enter the boot item.

3. Use the keyboard to move the party key, select boot option 1 and press enter to pop up the dialog box.

4. Press enter to confirm that (Kingston USB flash drive) has been set to the first finger to start.

5. Hard Drive BBS Priorities Option: Select the first boot option 1 and press Enter to pop up the dialog box. Go to the setting arrow key and move it to item 2 (Golden Bridge Stone Disk U Disk) and press Enter to confirm that different USB flash drives may have different displays, but be sure to set the U disk as the first start.

Follow the prompts to complete the installation, but the system installation disk will be emptied.

Based on your description, the following scenario is recommended:

1. The CPU is overloaded, or it is not working properly. Check CPU and graphics card cooling, dust removal, oiling, or replace fans.

Second, the power supply voltage is unstable and the power supply is insufficient. Replace high-quality, high-power power supplies.

3. Clean and defragment disks frequently.

1. In the "My Computer" window, right-click the drive letter you want to clean up - "Properties" - "Clean Disk" - check the files you want to delete - OK - Yes.

2. Clear the temporary file, start-run-enter "%temp%"-OK.

3. Clean up the registry and junk files with Optimizer or Super Bunny.

4. Close some startup programs, start-run-msconfig---start, in addition to anti-virus software, input method, general state programs can be turned off.

5. Delete unused program software.

7. Reduce the burden of memory, do not open too many programs. If you have too many documents open or too many programs running at the same time, you will not have enough memory to run other programs, so you should close the programs and windows you don't use at any time.

4. Upgrade the graphics card and network card driver, and change to a higher-grade graphics card.

5. Increase physical memory.

6. Immediately check for viruses, under normal circumstances, you can use antivirus or 360 fast detection and killing. Rapid scanning, which can remove running viruses, Trojans, and rogue software at one time.

You can change the U disk on other computers to start the beam Wang buried disk,** system put in,On this computer, restart the PE system,If the PE system can't get in,Shut down and unplug the hard disk cable and try again,If you can get in this way,There may be a problem with the hard disk,If you can enter PE normally,You can reinstall the system。

1. Came to the BIOS, the default is in the main menu, now select the "Devices" menu.

2. Select "ATA Drive Setup" below.

3. Select Configure SATA AS Enter.

4. Press Enter to pop up the "Configure SATA AS" dialog box, select "IDE" here.

5. Now set Configure SATA AS to "IDE".

6. Now press F10, save the settings, and click "Yes". Now that the setup is complete, the computer restarts, and the computer can be started normally. Hope.

Computer Blue Screen Reasons.

The situation you mentioned is generally caused by system software, memory, and hard disk.

1. If the computer is not installed with malware, or malicious programs are generated when surfing the Internet, it is recommended to use 360 Guard, Kingsoft Guardian and other software to clean up the garbage and kill the malware, which may be solved. It really doesn't work, reinstall and restore the system, you can solve the problems caused by the software.

2 If you can't enter the system, you can turn on the computer and go to the system selection there and press F8 to select the last correct configuration and security mode that works, and you may be able to enter the system.

Start Menu Run at 3 points Enter cmd and enter for %1 in (%windir% system32 *.) at the command promptdll) do s %1 and then enter. Then let him run it and it should be solved.

4 Recently, the computer has been poisoned, unstable software has been installed, etc., it is recommended to take a full antivirus, uninstall the software that caused the problem, and reinstall another version, which may be solved. No more, it's OK to reinstall the system

5 If the memory module in the computer case is dusty, disassemble the case, remove the memory module, clean the memory gold finger, and reinstall it.

6. If the memory of the computer is bad for a long time, the parallel memory is bought, and the multiple memories are incompatible when used together, etc., it is recommended to replace the memory to solve the problem.

7 The computer has been used for a long time, the hard disk is broken, and the logical bad sectors can be repaired by repartitioning and installing the system, but it still doesn't work, then it's time to change the hard disk, and it can be solved by changing the hard disk.

Note: If it is a software problem: the simplest, direct, thorough, effective and fast way is to reinstall the system. (Of course, some people may think that it is the most irresponsible statement, and the machine that has actually been used for a long time should have redone the system).

If there is a problem with the hardware, if you are not professional, it is recommended to take it to a computer store to test, and then change it after the test is good.

Hope it helps!!

You can format the hard drive to reinstall the system to try it out.

The computer appears, the blue screen 0x0000007b**, and the reason is simple.